SIST EN 13246:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Embalaža - Podrobni opis jeklenih povezovalnih trakovVerpackung - Spezifikation für Umreifungsbänder aus StahlEmballage - Spécifications relatives aux cerclages d'acierPackaging - Specification for tensional steel strapping77.140.50SROL]GHONLFlat steel products and semi-products55.040SDNLUDQMHPackaging materials and accessoriesICS:Ta slovenski standard je istoveten z:EN 13246:2001SIST EN 13246:2002en01-januar-2002SIST EN 13246:2002SLOVENSKI
STANDARD



SIST EN 13246:2002



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13246April 2001ICS 55.040English versionPackaging - Specification for tensional steel strappingEmballage - Spécifications relatives aux cerclages d'acierVerpackung - Spezifikation für Umreifungsbänder aus StahlThis European Standard was approved by CEN on 18 January 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13246:2001 ESIST EN 13246:2002



Page 2EN 13246:2001Contents PageForeword.31Scope.42Normative references.43Requirements.44Coil sizes and weights.8Annex A (informative)
Finishing.10Annex B (informative)
Bend test.11Bibliography.13SIST EN 13246:2002



Page 3EN 13246:2001ForewordThis European Standard has been prepared by Technical Committee CEN/TC 261 "Packaging", the secretariat ofwhich is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latestby October 2001.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,Switzerland and the United Kingdom.SIST EN 13246:2002



Page 4EN 13246:20011 ScopeThis European Standard specifies the dimensions and physical properties of a range of tensional steel strappingused to secure, close or strengthen packages and to band unit loads.The types of tensional steel strapping covered by this European Standard and their characteristics are listed inTable 1.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test (at ambient temperature)3 Requirements3.1 Mechanical propertiesThe minimum tensile strength and percentage elongation at break of tensional steel strapping in the specifiedrange shall be as shown in Table
...