SIST EN 60286-1:2018

SLOVENSKI STANDARD
SIST EN 60286-1:2018
01-januar-2018
1DGRPHãþD
SIST EN 60286-1:2002
3DNLUDQMHNRPSRQHQW]DDYWRPDWVNRUDYQDQMHGHO7UDNDQMHNRPSRQHQW]
RVQLPLL]YRGLSULNOMXþNLQDQHSUHNLQMHQLKWUDNRYLK,(&
Packaging of components for automatic handling - Part 1: Tape packaging of
components with axial leads on continuous tapes (IEC 60286-1:2017)
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung - Teil 1:
Gurtung von Bauelementen mit axialen Anschlüssen (IEC 60286-1:2017)
Emballage des composants pour opérations automatisées - Partie 1: Emballage des
composants à sorties axiales en bandes continues (IEC 60286-1:2017)
Ta slovenski standard je istoveten z: EN 60286-1:2017
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.060 Tulci. Vretena Spools. Bobbins
SIST EN 60286-1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60286-1:2018

---------------------- Page: 2 ----------------------

SIST EN 60286-1:2018


EUROPEAN STANDARD EN 60286-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2017
ICS 31.020; 31.240 Supersedes EN 60286-1:1998
English Version
Packaging of components for automatic handling -
Part 1: Tape packaging of components with axial leads
on continuous tapes
(IEC 60286-1:2017)
Emballage des composants pour opérations automatisées - Gurtung und Magazinierung von Bauelementen für
Partie 1: Emballage des composants à sorties axiales automatische Verarbeitung - Teil 1: Gurtung von
en bandes continues Bauelementen mit axialen Anschlüssen
(IEC 60286-1:2017) (IEC 60286-1:2017)
This European Standard was approved by CENELEC on 2017-08-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60286-1:2017 E

---------------------- Page: 3 ----------------------

SIST EN 60286-1:2018
EN 60286-1:2017
European foreword
The text of document 40/2538/FDIS, future edition 3 of IEC 60286-1, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60286-1:2017.

The following dates are fixed:
(dop) 2018-05-30
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-08-30
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60286-1:1998.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60286-1:2017 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60286-2 NOTE Harmonized as EN 60286-2.
IEC 60286-3 NOTE Harmonized as EN 60286-3.
IEC 60301 NOTE Harmonized as EN 60301.
2

---------------------- Page: 4 ----------------------

SIST EN 60286-1:2018
EN 60286-1:2017
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.

NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year

IEC 60294 -  Measurement of the dimensions of a EN 60294 -
cylindrical component with axial
terminations
ISO 11469 -  Plastics - Generic identification and EN ISO 11469 -
marking of plastics products

3

---------------------- Page: 5 ----------------------

SIST EN 60286-1:2018

---------------------- Page: 6 ----------------------

SIST EN 60286-1:2018



IEC 60286-1

®


Edition 3.0 2017-07




INTERNATIONAL



STANDARD



















Packaging of components for automatic handling –

Part 1: Tape packaging of components with axial leads on continuous tapes



























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 31.020; 31.240 ISBN 978-2-8322-4645-0



  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 60286-1:2018
– 2 – IEC 60286-1:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensions. 5
4.1 Dimensions common to tapes and taped components with axial leads . 5
4.1.1 General . 5
4.1.2 Body location (permissible lateral deviation) . 7
4.1.3 Tape spacing . 7
4.2 Taping . 7
4.2.1 General . 7
4.2.2 Orientation of polarized components . 8
4.2.3 Position, kinks and bends of the leads . 8
4.2.4 The ends of the leads . 8
4.2.5 Holding in the tape . 8
4.2.6 Requirements of tape material, storage, and handling . 8
4.2.7 Splices of tape . 8
4.2.8 Leader tape . 8
5 Packing . 8
5.1 General . 8
5.2 Dimensions of the reel . 9
5.3 Distances W and W . 9
1 2
5.4 Recycling . 9
5.5 Protection of components . 9
5.6 Reel filling . 9
5.7 Dimensions of the fan-fold container . 10
5.8 Missing components . 10
6 Marking . 10
Annex A (informative) Cross-reference for references to the previous edition of this
document . 11
Bibliography . 12

Figure 1 – Dimensions for tape packaging of components with axial leads . 6
Figure 2 – Reel dimensions . 9
Figure 3 – Outer dimensions of the fan-fold arrangement . 10


Table 1 – Tape widths and permissible variation . 6
Table 2 – Component spacing and permissible deviation . 7
Table 3 – Tape spacing. 7
Table A.1 – Cross-reference to clauses . 11

---------------------- Page: 8 ----------------------

SIST EN 60286-1:2018
IEC 60286-1:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING –

Part 1: Tape packaging of components
with axial leads on continuous tapes

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees
...