oSIST prEN 1501-1:2025
(Main)Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
This document applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2, regardless of the power drive.
This document deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its intended function and can be operated, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.
This document describes and defines the safety requirements of rear loaded RCVs excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) itself and excluding loader cranes, which could be mounted on the RCV.
Lifting device(s) and the interface with the tailgate/discharge door are covered in EN 1501-5:202X.
Loader cranes are covered in EN 12999:2020+A1:2025 and those installed on RCVs are covered in EN 1501-5:202X.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
- operation in severe conditions, e.g. extreme environmental conditions such as:
- below −20 °C and above +40 °C temperatures;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.
Abfallsammelfahrzeuge - Allgemeine Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader
Dieses Dokument ist für Hecklader-Abfallsammelfahrzeuge (ASF) nach 3.2 ungeachtet des Antriebs anzuwenden.
Dieses Dokument behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Ereignisse im Hinblick auf Hecklader ASF bei bestimmungsgemäßer Verwendung und bei Zuständen von Missbrauch, welche während der voraussichtlichen Lebensdauer vernünftigerweise vorhersehbar sind, wie in Abschnitt 4 festgelegt.
Dieses Dokument ist anzuwenden für die Gestaltung und Konstruktion des Hecklader-ASF, um sicherzustellen, dass es für seine bestimmungsgemäße Funktion geeignet ist und dass es während seiner gesamten Lebensdauer betrieben, gereinigt (einschließlich der Beseitigung einer Blockierung), eingestellt und instand gehalten werden kann. Es ist nicht anzuwenden für das Ende der Lebensdauer des Hecklader ASF.
Dieses Dokument beschreibt und legt die Sicherheitsanforderungen an Hecklader ASF unter Ausschluss der Schnittstelle Heckteil/Entladetür mit der/den Schüttung(en) und der/den Schüttung(en) selbst und unter Ausschluss von Ladekranen, die auf das ASF montiert werden könnten fest.
Schüttung(en) und die Schnittstelle mit dem Heckteil/der Entladetür werden in EN 1501 5:202X behandelt.
Ladekrane werden in EN 12999:2020+A1:2025 und an ASF installierte Ladekrane werden in EN 1501 5:202X behandelt.
Dieses Dokument ist auch anzuwenden für Verdichter, die auf einem LKW zu Sammelzwecken betrieben werden.
Dieses Dokument ist nicht anzuwenden für:
Betrieb unter Extrembedingungen, z. B. extreme Umgebungsbedingungen, wie:
Temperaturen unter −20 °C und über +40 °C;
tropische Umgebung;
Windgeschwindigkeiten von mehr als 75 km/h;
verunreinigende Umgebung;
korrosive Atmosphäre;
Betrieb in explosionsfähigen Atmosphären;
Handhabung von Ladungen, die Gefährdungssituationen auslösen könnten (z. B. heiße Abfälle, Säuren und Basen, radioaktive Stoffe, verunreinigter Abfall, besonders zerbrechliche Ladungen, Explosivstoffe);
Einsatz auf Schiffen.
Dieses Dokument ist nicht anzuwenden für Maschinen, die vor dem Datum der Veröffentlichung dieses Dokumentes durch CEN hergestellt wurden.
Véhicules de collecte de déchets - Exigences générales et exigences de sécurité - Partie 1 : Véhicules de collecte de déchets à chargement arrière
Le présent document s’applique aux véhicules de collecte de déchets (V.C.D.) à chargement arrière, tels que définis en 3.2, quelle que soit leur motorisation.
Le présent document traite de tous les dangers, situations et phénomènes dangereux importants relatifs aux V.C.D. à chargement arrière, tels que définis à l’Article 4, lorsqu’ils sont utilisés conformément aux attentes et dans des conditions de mauvaise utilisation raisonnablement prévisibles, durant toute leur durée de vie prévue.
Le présent document est applicable à la conception et à la fabrication des V.C.D. à chargement arrière, en vue de garantir que les véhicules puissent accomplir leur fonction prévue et être utilisés, nettoyés (déblocage compris), réglés et entretenus durant leur durée de vie entière. Il ne s’applique pas à la fin de vie des V.C.D. à chargement arrière.
Le présent document décrit et définit les exigences de sécurité des V.C.D. à chargement arrière, à l’exclusion de l’interface de la porte arrière/porte de déchargement avec le ou les lève conteneurs et du ou des lève conteneurs eux mêmes, et à l’exclusion des grues de chargement pouvant être montées sur les V.C.D.
Le ou les lève conteneurs et l’interface avec la porte arrière/porte de déchargement sont couvertes dans l’EN 1501-5:202X.
Les grues de chargement sont couvertes dans l’EN 12999:2020+A1:2025 et celles installées sur des V.C.D. sont couvertes par l’EN 1501-5:202X.
Le présent document s’applique également aux compacteurs utilisés sur un camion pour la collecte.
Le présent document ne s’applique pas :
- au fonctionnement dans des conditions difficiles, par exemple, des conditions environnementales extrêmes, telles que :
- des températures inférieures à −20 °C et supérieures à +40 °C ;
- un environnement tropical ;
- une vitesse de vent dépassant 75 km/h ;
- aux milieux polluants ;
- aux environnements corrosifs ;
- au fonctionnement dans des atmosphères potentiellement explosives ;
- à la manutention de chargements dont la nature pourrait donner lieu à des situations dangereuses (par exemple, déchets chauds, acides et bases, matériaux radioactifs, déchets contaminés, chargements particulièrement fragiles, explosifs) ;
- au fonctionnement sur les navires.
Le présent document ne s’applique pas aux machines fabriquées avant la date de publication de ce document par le CEN.
Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za zbiranje odpadkov z nakladanjem zadaj
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2025
Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za
zbiranje odpadkov z nakladanjem zadaj
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear
loaded refuse collection vehicles
Abfallsammelfahrzeuge - Allgemeine Anforderungen und Sicherheitsanforderungen -
Teil 1: Hecklader
Véhicules de collecte de déchets - Exigences générales et exigences de sécurité - Partie
1 : Véhicules de collecte de déchets à chargement arrière
Ta slovenski standard je istoveten z: prEN 1501-1
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
43.160 Vozila za posebne namene Special purpose vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2025
ICS 43.160 Will supersede EN 1501-1:2021
English Version
Refuse collection vehicles - General requirements and
safety requirements - Part 1: Rear loaded refuse collection
vehicles
Véhicules de collecte de déchets - Exigences générales Abfallsammelfahrzeuge - Allgemeine Anforderungen
et exigences de sécurité - Partie 1 : Véhicules de und Sicherheitsanforderungen - Teil 1: Hecklader
collecte de déchets à chargement arrière
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 183.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1501-1:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 5
Introduction . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 12
4 List of significant hazards . 19
5 Safety requirements and protective measures . 22
5.1 General. 22
5.2 Danger zones . 23
5.2.1 General. 23
5.2.2 Verification . 25
5.3 Compaction mechanism . 26
5.3.1 General. 26
5.3.2 Interaction between bodywork and compaction mechanism . 26
5.3.3 Hopper . 26
5.3.4 Relationship between the compaction mechanism and the load opening edge . 26
5.3.5 Guide flap . 27
5.3.6 Additional equipment(s) . 27
5.3.7 Guards . 27
5.3.8 Electro-sensitive protective equipment (ESPE) . 27
5.3.9 Controls for the compaction mechanism . 27
5.4 Discharge system . 28
5.4.1 Controls for discharge system . 28
5.4.2 Operation conditions for the tailgate or discharge door . 29
5.4.3 Operation conditions for emptying the body and the tailgate . 29
5.4.4 Hinged adaptation frame . 29
5.5 Requirements for the refuse container lifting device(s) . 29
5.6 Position of the refuse container lifting device in relation to the compaction
mechanism . 30
5.7 Satellite vehicle . 30
5.8 Hydraulic, pneumatic and electric systems. 30
5.8.1 Hydraulic system . 30
5.8.2 Pneumatic system . 30
5.8.3 Electric system . 30
5.9 Operating symbols . 30
5.10 Riding on rear loaded RCV by operator(s) . 33
5.10.1 General. 33
5.10.2 Cab . 33
5.10.3 Footboard(s) and handles . 33
5.11 Control systems . 38
5.11.1 General requirements for safety circuits . 38
5.11.2 Emergency stop devices . 38
5.11.3 Control devices . 39
5.12 Monitoring and warning. 40
5.12.1 Closed circuit television system . 40
5.12.2 Communication . 41
5.12.3 Warnings . 41
5.13 Electrical components. 43
5.13.1 General . 43
5.13.2 Protective interlocks . 43
5.13.3 Two-hand operating controls. 43
5.13.4 Overload protection. 43
5.13.5 Energy interruption . 43
5.13.6 Position sensors . 43
5.13.7 Terminals and wire connections . 43
5.13.8 Electric cables and wiring harness . 44
5.13.9 Working lights . 44
5.14 Requirements for maintenance . 44
5.14.1 Unexpected start-up . 44
5.14.2 Raised tailgate or discharge door or tilting body . 44
5.14.3 Access and inspection door(s) . 44
5.14.4 Cleaning . 44
5.15 Stability and driving security . 45
5.15.1 General . 45
5.15.2 Stability in refuse container lifting mode . 45
5.15.3 Stability in discharging mode . 45
5.15.4 Lateral stability . 45
5.15.5 Minimum front axle mass . 45
5.16 Exhaust pipe . 45
5.17 Measures regarding explosions . 45
5.18 Vibration . 46
5.19 Noise control .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.