iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1293:2000

(Main)

General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers

General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers

This standard specifies general requirements for components for use in pneumatically pressurized discharge pipes, drains and sewers. This European Standard provides the general basis for the preparation or revision of product standards. Some of the provisions may need modifications when drafting harmonized European Standards. It is not applicable for the evaluation of products.

Allgemeine Anforderungen an Bauteile von pneumatisch betriebenen Abwasserdruckleitungen

Diese Europäische Norm legt allgemeine Anforderungen an Bauteile für pneumatisch betriebenen Abwasserdruckleitungen fest. Diese Europäische Norm dient als allgemeine Grundlage für die Ausarbeitung oder Überarbeitung von Produktnormen. Einige Festlegungen können möglicherweise bei der Ausarbeitung harmonisierter Europäischer Normen modifiziert werden. Sie gilt nicht für die Bewertung von Produkten.

Prescriptions générales pour les composants utilisés dans les réseaux d'évacuation, de branchement et d'assainissement sous pression pneumatique

La présente norme européenne établit les prescriptions générales applicables aux composants utilisés dans les réseaux d'évacuation, de branchement et d'assainissement sous pression pneumatique. La présente norme européenne constitue la base générale pour la préparation ou la révision des normes de produits. Certaines de ces dispositions peuvent nécessiter des modifications lors de la préparation des normes européennes harmonisées. Elle ne s'applique pas a l'évaluation des produits.

Splošne zahteve za sestavne dele, ki se uporabljajo za tlačne kanalizacijske sisteme in drenaže

General Information

Status
Withdrawn
Publication Date
31-Oct-2000
Withdrawal Date
21-Sep-2011
ICS
93.030 - External sewage systems
Technical Committee
IOVO - Water supply and waste water engineering
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
21-Sep-2011
Due Date
14-Oct-2011
Completion Date
22-Sep-2011
Directive
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
EN 1293:1999 - General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers

Relations

Replaced By
SIST EN 476:2011 - General requirements for components used in drains and sewers
Effective Date
01-Nov-2011

Buy Standard

EN 1293:2000EN 1293:2000
PreviousNext
Standard
EN 1293:2000
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.DOL]DFLMVNHAllgemeine Anforderungen an Bauteile von pneumatisch betriebenen AbwasserdruckleitungenPrescriptions générales pour les composants utilisés dans les réseaux d'évacuation, de branchement et d'assainissement sous pression pneumatiqueGeneral requirements for components used in pneumatically pressurized discharge pipes, drains and sewers93.030Zunanji sistemi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12889:2023(Main)
Trenchless construction and testing of drains and sewers
EN 12889:2022

This document is applicable to the trenchless construction, trenchless replacement techniques and testing of new drains and new sewers in the ground usually operating as gravity or pressure pipelines, formed using prefabricated pipes and their joints.
Renovation techniques for existing pressure and non-pressure systems are not covered by this document.
Methods of trenchless construction include:
-   manned and unmanned techniques;
-   steerable and non-steerable techniques.
Mining or tunnelling (e.g. in situ construction or the use of prefabricated segments) are not covered by this document although some parts may apply to these methods.
Requirements for associated pipeline installation work other than trenchless construction, e.g. for manholes and inspection chambers, are not covered by this document and are specified in EN 1610. This also applies to pipes that are subsequently installed within entry and exit shafts/pits.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11296-9:2023(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
EN ISO 11296-9:2022

This document, in conjunction with EN ISO 11296-1, specifies requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement.
It does not apply to the structural design of the lining system.
NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this Standard.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 476:2022(Main)
General requirements for components used in drains and sewers
EN 476:2022

This document specifies general requirements to be respected in product standards for components such as pipes, fittings, inspection chambers and manholes with their respective joints intended for use in drains and sewers inside and outside buildings which operate as gravity systems allowing for a maximum pressure of 40 kPa.
It also specifies general requirements for components used in hydraulically and pneumatically pressurized discharge pipes, drains and sewers.
NOTE 1   Where the term "inside buildings" is used in the context of components fixed inside buildings, it also includes discharge pipes and fittings fixed on external surfaces of buildings
NOTE 2   This document is not a product standard and therefore not intended for the direct evaluation of products.
This document covers components to be used in conveying in a satisfactory manner:
-   domestic wastewater;
-   rainwater and surface water; and
-   other waste waters acceptable for discharge into the system (e.g. industrial wastewater).
This document applies to components of circular and other cross sections.
This document applies equally to components which are factory-made and to those constructed on site, where applicable.
NOTE 3   This document does not apply to components used for trenchless construction according to EN 14457 and for components used for renovation of drains and sewers according to EN 13380.
This document does not supersede the functional requirements of a complete system as defined in EN 752.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16933-1:2022(Main)
Drain and sewer systems outside buildings - Design - Part 1: Layout principles
EN 16933-1:2022

This document specifies requirements for the design of drain and sewer systems outside buildings.
It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where the wastewater leaves a building, roof drainage system, or paved area, to a point where it is discharged into a wastewater treatment plant or receiving water body.
This part specifies requirements for the layout of drain and sewer systems.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14654-2:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 2: Rehabilitation
EN 14654-2:2021

This European Standard establishes requirements for the management and control of operational activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This part covers the management and control of rehabilitation activities.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14654-4:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 4: Control of inputs from users
EN 14654-4:2021

This European Standard establishes the general principles for the management and control of operational activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document together with EN 14654-1 covers the management and control of inputs from users.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14654-3:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 3: Drain and sewer cleaning
EN 14654-3:2021

This European Standard establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document covers the management and control of sewer cleaning.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14654-1:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 1: General requirements
EN 14654-1:2021

This European Standard establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document covers general requirements for the management and control of activities.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1295-1:2019(Main)
Structural design of buried pipelines under various conditions of loading - Part 1: General requirements
EN 1295-1:2019

This document specifies the requirements for the structural design of water supply pipelines, drains
and sewers, and other water industry pipelines, whether operating at atmospheric, greater or lesser
pressure.
In addition, this document gives guidance on the application of the nationally established methods of
design declared by and used in CEN member countries at the time of preparation of this document.
This guidance is an important source of design expertise, but it cannot include all possible special cases,
in which extensions or restrictions to the basic design methods may apply.
Since in practice precise details of types of soil and installation conditions are not always available at
the design stage, the choice of design assumptions is left to the judgement of the engineer. In this
connection the guide can only provide general indications and advice.
This document specifies the requirements for structural design and indicates the references and the
basic principles of the nationally established methods of design (see Annexes A and B).

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15885:2019(Main)
Classification and characteristics of techniques for renovation, repair and replacement of drains and sewers
EN 15885:2018

This European Standard specifies a system for the classification of trenchless techniques for renovation, repair and replacement on the same line of drains and sewers outside buildings, operated under gravity or pressure, including pipes, connections and manholes. It defines and describes families of techniques and their different generic methods and materials used.
This European Standard does not apply for replacement by open trenching according to EN 1610 and trenchless construction and testing of drains and sewers as new construction off-the-line of the existing drain or sewer according to EN 12889.
This European Standard does not apply for the specification of requirements for specific products.
For each technique family it lists relevant existing standards, materials and applications and outlines characteristics including installation aspects, structural and hydraulic capabilities and site impact.
This standard does not apply to any work required on the existing pipe prior to renovation, repair or replacement.
This European Standard provides information needed to determine viable options for identification of the optimal technique with regard to a given set of renovation, repair or replacement objectives.
NOTE   It is the responsibility of the designer to choose and design the renovation and repair systems.
It does not specify the calculation methods to determine, for each viable technique, the required amount of material needed to secure the desired performance of the pipeline to be rehabilitated.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day