SIST EN ISO 16000-9:2024

SLOVENSKI STANDARD
oSIST prEN ISO 16000-9:2023
01-marec-2023
Notranji zrak - 9. del: Določevanje emisije hlapnih organskih spojin iz gradbenih
proizvodov in opreme - Metoda s preskusno komoro (ISO/DIS 16000-9:2023)
Indoor air - Part 9: Determination of the emission of volatile organic compounds from
building products and furnishing - Emission test chamber method (ISO/DIS 16000-
9:2023)
Innenraumluftverunreinigungen - Teil 9: Bestimmung der Emission von flüchtigen
organischen Verbindungen aus Bauprodukten und Einrichtungsgegenständen -
Emissionsprüfkammer-Verfahren (ISO/DIS 16000-9:2023)
Air intérieur - Partie 9: Dosage de l'émission de composés organiques volatils de
produits de construction et d'objets d'équipement - Méthode de la chambre d'essai
d'émission (ISO/DIS 16000-9:2023)
Ta slovenski standard je istoveten z: prEN ISO 16000-9 rev
ICS:
13.040.20 Kakovost okoljskega zraka Ambient atmospheres
oSIST prEN ISO 16000-9:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN ISO 16000-9:2023
oSIST prEN ISO 16000-9:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 16000-9
ISO/TC 146/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-01-25 2023-04-19
Indoor air —
Part 9:
Determination of the emission of volatile organic
compounds from building products and furnishing -
Emission test chamber method
Air intérieur —
Partie 9: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets
d'équipement — Méthode de la chambre d'essai d'émission
ICS: 13.040.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 16000-9:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

oSIST prEN ISO 16000-9:2023
ISO/DIS 16000-9:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 16000-9
ISO/TC 146/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:

Indoor air —
Part 9:
Determination of the emission of volatile organic
compounds from building products and furnishing -
Emission test chamber method
Air intérieur —
Partie 9: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets
d'équipement — Méthode de la chambre d'essai d'émission
ICS: 13.040.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 16000-9:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

oSIST prEN ISO 16000-9:2023
ISO/DIS 16000-9:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms.3
5 Principle . 4
6 Emission test chamber system. 4
6.1 General . 4
6.2 Emission test chamber materials . 4
6.3 Air supply and mixing facilities . 4
6.4 Air tightness . 5
6.5 Air sampling devices . 5
6.6 Recovery and sink effects . 5
7 Apparatus . 6
8 Test conditions .6
8.1 Temperature and relative air humidity . 6
8.2 Supply air quality and background concentration . 6
8.3 Air velocity . 6
8.4 Area specific air flow rate and air change rate. 7
9 Verification of the test conditions .7
9.1 General . 7
9.2 Temperature and relative air humidity control systems. 7
9.3 Air change rate in the emission test chamber . 7
9.4 Emission test chamber air tightness . 7
9.5 Air velocity in the emission test chamber . 7
9.6 Efficiency of the internal emission test chamber air mixing . 8
10 Test specimens . 8
11 Emission test chamber preparation . 8
12 Test method . 8
12.1 Background concentrations . 8
12.2 Test specimen location in the emission test chamber . 8
12.3 Time for measurements of test chamber air concentration . 8
13 Calculation of area specific emission rates and expression of results .9
14 Performance characteristics . 9
15 Test report . 9
Annex A (normative) System for quality assurance and quality control .11
Annex B (informative) Examples of loading factors for a model room .13
Annex C (informative) General description of an emission test chamber .14
Annex D (informative) Determination of the emission rates of cut edges .15
Bibliography .18
iii
oSIST prEN ISO 16000-9:2023
ISO/DIS 16000-9:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 6,
Indoor air.
This second edition cancels and replaces the first edition (ISO 16000-9:2011), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— detailed information about cut edge and temperature effects has been added.
A list of all parts in the ISO 16000 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
com
...