SIST EN ISO 15750-2:2008

SLOVENSKI STANDARD
SIST EN ISO 15750-2:2008
01-oktober-2008
Embalaža - Jekleni sodi - 2. del: Sodi z nesnemljivim pokrovom (ozka odprtina) z
najmanjšo prostornino 212 l, 216,5 l in 230 l (ISO 15750-2:2002)
Packaging - Steel drums - Part 2: Non-removable head (tight head) drums with a
minimum total capacity of 212 l, 216,5 l and 230 l (ISO 15750-2:2002)
Verpackung - Stahlfässer - Teil 2: Spundfässer mit einem Gesamtvolumen von
mindestens 212 l, 216,5 l und 230 l (ISO 15750-2:2002)
Emballages - Futs en acier - Partie 2: Futs a ouverture partielle d'une capacité totale
minimale de 212 l, 216,5 l et 230 l (ISO 15750-2:2002)
Ta slovenski standard je istoveten z: EN ISO 15750-2:2008
ICS:
55.140 6RGL.RYLQVNLVRGL5RþNH Barrels. Drums. Canisters
SIST EN ISO 15750-2:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15750-2:2008

---------------------- Page: 2 ----------------------

SIST EN ISO 15750-2:2008
EUROPEAN STANDARD
EN ISO 15750-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 55.140

English Version
Packaging - Steel drums - Part 2: Non-removable head (tight
head) drums with a minimum total capacity of 212 l, 216,5 l and
230 l (ISO 15750-2:2002)
Emballages - Fûts en acier - Partie 2: Fûts à ouverture Verpackung - Stahlfässer - Teil 2: Spundfässer mit einem
partielle d'une capacité totale minimale de 212 l, 216,5 l et Gesamtvolumen von mindestens 212 l, 216,5 l und 230 l
230 l (ISO 15750-2:2002) (ISO 15750-2:2002)
This European Standard was approved by CEN on 16 May 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15750-2:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15750-2:2008
EN ISO 15750-2:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15750-2:2008
EN ISO 15750-2:2008 (E)
Foreword
The text of ISO 15750-2:2002 has been prepared by Technical Committee ISO/TC 122 “Packaging” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 15750-2:2008 by
Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn
at the latest by December 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15750-2:2002 has been approved by CEN as a EN ISO 15750-2:2008 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 15750-2:2008

---------------------- Page: 6 ----------------------

SIST EN ISO 15750-2:2008
INTERNATIONAL ISO
STANDARD 15750-2
First edition
2002-04-15
Packaging — Steel drums —
Part 2:
Non-removable head (tight head) drums
with a minimum total capacity of 212 l,
216,5 l and 230 l
Emballages — Fûts en acier —
Partie 2: Fûts à ouverture partielle d'une capacité totale minimale de 212 l,
216,5 l et 230 l
Reference number
ISO 15750-2:2002(E)
©
ISO 2002

---------------------- Page: 7 ----------------------

SIST EN ISO 15750-2:2008
ISO 15750-2:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15750-2:2008
ISO 15750-2:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 15750 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15750-2 was prepared by Technical Committee ISO/TC 122, Packaging.
ISO 15750 consists of the following parts, under the general title Packaging — Steel drums:
— Part 1: Removable head (open head) drums with a minimum total capacity of 208 l, 210 l and 216,5 l
— Part 2: Non-removable head (tight head) drums with a minimum total capacity of 212 l, 216,5 l and 230 l
— Part 3: Inserted flange-type closure systems
Annexes A and B form a normative part of this part of ISO 15750.
© ISO 2002 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 15750-2:2008
ISO 15750-2:2002(E)
Introduction
Throughout the world a large number of steel drum types with different dimensions and characteristics are being
used. The differences in location of the filling opening and outer dimensions result in differences in filling, handling
and transportation.
This part of ISO 15750 gives uniform specifications for three main types of drums for use in international trade and
the preferred target option is drum type A (see Table 1).
It specifies the characteristics and dimensions of steel drums which are of importance for the exchangeability and
does not give detailed performance requirements and related test methods. The performance requirements depend
on the specific application.
Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory
requirements which govern the transport of those goods in the countries concerned, including capseals/overseals
fitted in accordance with the certificate. Depending upon the mode of transport, this means meeting the
requirements of:
 UN (United Nations): Recommendations on the transport of dangerous goods. Model regulations;
 ICAO (International Civil Aviation Organization): Technical instructions for safe transport of dangerous goods
by air ;
 IMO (International Maritime Organization): International Maritime Dangerous Goods (IMDG) Code.
This involves the certification and marking of the drums according to the regulations.
iv © ISO 2002 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 15750-2:2008
INTERNATIONAL STANDARD ISO 15750-2:2002(E)
Packaging — Steel drums —
Part 2:
Non-removable head (tight head) drums with a minimum total
capacity of 212 l, 216,5 l and 230 l
1 Scope
This part of ISO 15750 specifies the characteristics and dimensions of non-removable head (tight head) drums,
manufactured from steel sheet, having a total capacity of 212 l, 216,5 l and 230 l.
It also specifies a method for measuring the total capacity and brimful capacity, and a draining test method.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 15750. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 15750 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 228-1:2000 Pipe threads where pressure-tight joints ar
...