SIST EN ISO 4254-7:2018/A1:2026

SLOVENSKI STANDARD
01-julij-2026
Kmetijski stroji - Varnost - 7. del: Splošni kombajni, kombajni za pripravo krme,
obiranje bombaža in žetev sladkornega trsa - Dopolnilo A1 (ISO 4254-7:2017/Amd
1:2025)
Agricultural machinery - Safety - Part 7: Combine harvesters, forage harvesters, cotton
harvesters and sugar cane harvesters - Amendment 1 (ISO 4254-7:2017/Amd 1:2025)
Landmaschinen - Sicherheit - Teil 7: Mähdrescher, Feldhäcksler,
Baumwollerntemaschinen und Zuckerrohrerntemaschinen - Änderung 1 (ISO 4254-
7:2017/Amd 1:2025)
Matériel agricole - Sécurité - Partie 7: Moissonneuses-batteuses, récolteuses-
hacheuses-chargeuses de fourrage, récolteuses de coton et récolteuses de cannes à
sucre - Amendement 1 (ISO 4254-7:2017/Amd 1:2025)
Ta slovenski standard je istoveten z: EN ISO 4254-7:2017/A1:2026
ICS:
65.060.50 Oprema za spravilo pridelkov Harvesting equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 4254-7:2017/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2026
EUROPÄISCHE NORM
ICS 65.060.50
English Version
Agricultural machinery - Safety - Part 7: Combine
harvesters, forage harvesters, cotton harvesters and sugar
cane harvesters - Amendment 1 (ISO 4254-7:2017/Amd
1:2025)
Matériel agricole - Sécurité - Partie 7: Moissonneuses- Landmaschinen - Sicherheit - Teil 7: Mähdrescher,
batteuses, récolteuses-hacheuses-chargeuses de Feldhäcksler, Baumwollerntemaschinen und
fourrage, récolteuses de coton et récolteuses de cannes Zuckerrohrerntemaschinen - Änderung 1 (ISO 4254-
à sucre - Amendement 1 (ISO 4254-7:2017/Amd 7:2017/Amd 1:2025)
1:2025)
This amendment A1 modifies the European Standard EN ISO 4254-7:2017; it was approved by CEN on 1 March 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4254-7:2017/A1:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4
European foreword
This document (EN ISO 4254-7:2017/A1:2026) has been prepared by Technical Committee ISO/TC 23
"Tractors and machinery for agriculture and forestry" in collaboration with Technical Committee
CEN/TC 144 “Tractors and machinery for agriculture and forestry” the secretariat of which is held by
AFNOR.
This Amendment to the European Standard EN ISO 4254-7:2017 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by November 2026,
and conflicting national standards shall be withdrawn at the latest by November 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 4254-7:2017/Amd 1:2025 has been approved by CEN as EN ISO 4254-7:2017/A1:2026
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
EU Directive 2006/42/EC of this EN
1.1.2.a) Principles of safety integration 4; 5; 6; 7; 8; 9;10
1.1.2.c) Principles of safety integration 4; 5; 6; 7; 8; 9;10
1.1.2.d) Principles of safety integration 4; 5; 6; 7; 8; 9;10
1.1.2.e) Principles of safety integration 4; 5; 6; 7; 8; 9;10
1.1.3.e) Materials and products 4.10.3; 4.16; 4.17.1
1.1.4 Lighting 4.3.11.7
1.1.5 Design of machinery to facilitate its 4.1; 4.2; 4.3; 4.4; 4.5; 4.8;
handling 4.9.1; 4.9.3; 4.9.4; 4.9.5; 4.12;
4.13.3; 4.17; 5.1; 5.2; 5.4.5.2;
6.1; 6.2.5; 7.1.2.1; 7.2.2.1;
7.3; 8.3; 8.5; 10
1.1.6 Ergonomics 4.1; 4.2; 4.3; 4.4; 4.5; 4.9.1;
4.9.3; 4.9.6.2, 4.12; 4.13.3;
5.2; 5.4.5.2; 6.1; 6.2.5;
7.1.2.1; 7.2.2.1; 7.3; 8.5
1.1.7 Operating positions 4.1.3; 4.3; 4.4; 6.1
1.1.8 Seating 4.3.1; 4.3.2
1.2.1 Safety and reliability of control 4.2; 4.3.9; 4.7; 4.16; 4.17; 8.2
systems
1.2.2 Control devices 4.2; 4.3; 4.12; 4.13.3; 4.14;
5.4.5.2; 6.2.5; 6.4; 7.1.2.1;
7.2.2.1; 8.5
1.2.3 Starting 4.3.9; 4.12; 4.13.3; 5.4.5.2;
6.2.5; 6.3; 7.1.2.1; 7.2.2.1
1.2.4 Stopping 4.1.3; 4.2; 4.3.9
1.2.6 Failure of the power supply 4.1.3; 4.2.3; 4.3.9; 4.7; 4.9.4;
4.12.2; 4.13; 4.16; 4.17.1;
5.4.5.2; 6.2.5; 7.2.2.1; 8.5
1.3.1 Risk of loss of stability 4.1.3; 4.9.4; 4.9.5; 7.2.3; 10.1,
10.2
1.3.2 Risk of break-up during operation 4.9.4; 4.16
1.3.3 Risks due to falling or ejected objects 4.1.3; 4.5; 4.9.4; 4.16; 5.5.2;
5.6.1.2; 5.6.5; 5.7; 6.5.1
1.3.4 Risks due to surfaces, edges or angles 4.1; 4.8
4.1.3; 4.2.2; 4.2.3; 4.3.3, 4.3.5;
4.3.7; 4.17.1; 5.3; 5.4.1; 5.4.2;
5.4.3; 5.4.4; 5.4.5.1; 5.5;
5.6.2; 5.6.3; 5.6.4; 5.8; 6.2;
6.5.1; 6.5.2; 7.1.2.1.2; 7.2.1;
7.2.2
1.3.7 Risks related to moving parts 4.2.1; 4.2.3; 4.3.4; 4.3.5; 4.5;
4.9.4; 5.3; 5.4; 5.5; 6.2; 6.3;
6.4; 6.5; 7.1; 7.2; 8.5; 8.6;
10.1; 10.2.3
1.3.8.1 Moving power transmission parts 4.6.2
1.3.8.2 Moving parts involved in the process 5.3; 5.4; 5.5; 5.6; 6.2; 6.3; 6.4;
6.5; 7.1; 7.2; 8.5; 8.6
1.3.9 Risks of uncontrolled movement 4.2.3; 4.5; 4.9.4
1.4.1 General requirements 5.6.2
1.4.2.1 Fixed guards 5.5.2.2
1.5.1 Electricity supply 4.9.2; 4.13.2; 4.17
1.5.3 Energy supply other than electricity 4.6.2; 4.16
1.5.4 Errors of fitting 4.1.3; 4.6.2; 10.1
1.5.5 Extreme temperatures 4.8
1.5.6 Fire 4.9.3; 4.10; 10.1.2
1.5.8 Noise 4.15
1.5.9 Vibrations  Not covered
1.5.10 Radiation  Not covered
1.5.11 External radiation  Not covered
1.5.12 Laser radiation  Not covered
1.5.13 Emissions of hazardous materials 4.3.12.5; 4.9.2.1; 4.9.3;
and substances 4.10.3; 4.16
1.5.14 Risk of being trapped in a machine 4.3.12.4
1.5.15 Risk of slipping, tripping or falling 4.3; 4.4; 5.2; 5.4.2; 7.2.4; 8.3;
10.1.3
1.6.1 Machinery maintenance 4.4; 4.9.3; 4.9.4; 5.4.2; 7.2.1;
7.2.2; 7.2.4; 8.4; 10.1
1.6.2 Access to operating positions and 4.2.1.3; 4.3.5; 4.3.8; 4.3.9.2;
service points 4.4; 4.9.2; 4.9.3; 4.9.4; 5.4.2;
5.4.3; 7.2.1; 7.2.2; 7.2.4; 8.4;
10.1
1.6.3 Isolation of energy sources 4.9.2; 4.13.2
1.6.4 Operator intervention 4.1; 4.2; 4.3.3; 4.3.8; 4.3.9;
4.4; 4.9.3; 4.9.4; 4.12; 4.13.3;
5.4.5.2; 6.2.5; 6.3; 6.4; 6.5;
7.1.2.1; 7.2.2.1; 8.5
1.7.1 Information and warnings on the 10
machinery
1.7.1.1 Information and information devices 10
1.7.1.2 Warning devices 5.1.2
1.7.2 Warning of residual risks 5.5.1.2; 5.6.1.2; 10.1; 10.2.3.2
1.7.3 Marking of machinery 10.2.1
1.7.4.1 General principles for the drafting of 10.1
instructions
1.7.4.2 Contents of the instructions 10.1
3.2.1 Driving position 4.3.4; 4.3.11
3.2.2 Seating 4.3.1; 5.1.1; 8.1
3.2.3 Positions for other persons 4.3.2
3.3 Control systems 4.2.3
3.3.1 Control devices 4.2.1; 4.2.2; 4.2.3; 4.3.1.1;
4.3.3; 4.3.8; 4.3.9; 4.7; 4.12;
4.13.3; 4.14; 5.4.5.2; 6.2.5;
7.1.2.1; 7.2.2.1; 8.5; 10.1.2
3.3.2 Starting/moving 4.2.1.5; 4.2.3; 4.5
3.3.3 Traveling function Not covered
3.3.5 Control circuit failure Not covered
3.4.1 Uncontrolled movements 4.1.3
3.4.2. Moving transmission parts  Not covered
3.4.3 Roll-over and tip-over Not covered
3.4.5 Means of access 4.2.1; 4.3; 4.4; 4.12.2; 4.13.3;
4.14; 5.2; 5.4.5.2; 6.2.5;
7.1.2.1; 8.3
3.4.6 Towing devices Not covered
3.4.7 Transmission of power between self- 4.1.3; 4.6.2
propelled machinery (or tractor) and
recipient machinery
3.5.1 Batteries 4.9.2
3.5.2 Fire 4.9.3; 4.10
3.6.1 Signs, signals and warnings 4.3.11.5; 4.8; 5.1.2; 5.6.5;
7.2.3; 10.1.2; 10.2.2; 10.2.3
3.6.2 Marking 10.2
3.6.3.1 Vibrations 10.1.1.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the
...