iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1948-3:1999

(Main)

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 3: Identification and quantification

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 3: Identification and quantification

The present Part of the Standard specifies the identification and quantificationprocedures of the sampled PCDDs/PCDFs. It is an integral part of the complete measurement procedure. The use of the other two parts of this Standard, EN 1948-1:1996 and EN 1948-2:1996, describing sampling and extraction and clean-up, respectively, is necessary for the determination of the PCDDs/PCDFs. This Stan- dard has been designed to measure PCDD/PCDF concentrations at about 0,1 ng I-TEQ/m cube in stationary source emissions.

Emissionen aus stationären Quellen - Bestimmung der Massenkonzentration von PCDDs/PCDFs - Teil 3: Identifizierung und Quantifizierung

Der vorliegende Teil der Norm das Identifizierungs- und Quantifizierungs- verfahren für die gesammelten PCDD/PCDF fest. Er ist integraler Bestandteil des vollständigen Messverfahrens. Die Anwendung der anderen beiden Teile dieserNorm EN 1948-1:1996 und EN 1948-2:1996, die die Probenahme bzw. die Extraktion und Reinigung beschreiben, ist notwendig für die Bestimmung der PCDD und PCDF. Diese Norm ist für die Messung von PCDD/PCDF-Emissionskonzentrationen von stationären Quellen im Bereich von 0,1 ng I-TEQ/m3 konzipiert.

Emissions de sources fixes - Détermination de la concentration massique en PCDDs/PCDFs - Partie 3: Identification et quantification

La présente partie de la N.E. spécifie des procédures d'identification et quan- tification pour les échantillons de PCDD/PCDF prélevés. Elle est partie intég- rante de la procédure complète de mesure. L'utilisation des deux autres parties de l'EN 1948-1:1996 et EN 1948-2:1996 décrivant d'une part le prélèvement, d'autre part l'extraction et la purification est nécessaure pour la détermi- nation des PCDD et PCDF. Cette norme a été préparée pour mesurer des concentra- tions au niveau 0,1 ng I-TEQ/m cube dans les émissions de sources fixes

Emisije nepremičnih virov – Določevanje masne koncentracije PCDD/PCDF – 3. del: Identifikacija in kvantifikacija

General Information

Status
Withdrawn
Publication Date
31-Aug-1999
Withdrawal Date
30-Apr-2006
ICS
13.040.40 - Stationary source emissions
Technical Committee
KAZ - Air quality
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-May-2006
Due Date
01-May-2006
Completion Date
01-May-2006
Directive
89/369/EEC - Prevention of air pollution from new municipal waste incineration plants
89/429/EEC - Reduction of air pollution from existing municipal waste incineration plants
94/67/EC - Incineration of hazardous waste
Mandate
M/BC/CEN/91/12 - Standardization mandate for CEN concerning a standardized measurement method for dioxins and furans emissions in exhausted gas
Ref Project
EN 1948-3:1996 - Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 3: Identification and quantification

Relations

Replaced By
SIST EN 1948-3:2006 - Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 3: Identification and quantification of PCDDs/PCDFs
Effective Date
01-May-2006

Buy Standard

EN 1948-3:1999EN 1948-3:1999
PreviousNext
Standard
EN 1948-3:1999
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-1999
(PLVLMHQHSUHPLþQLKYLURY±'RORþHYDQMHPDVQHNRQFHQWUDFLMH3&''3&')±
GHO,GHQWLILNDFLMDLQNYDQWLILNDFLMD
Stationary source emissions - Determination of the mass concentration of
PCDDs/PCDFs - Part 3: Identification and quantification
Emissionen aus stationären Quellen - Bestimmung der Massenkonzentration von
PCDDs/PCDFs - Teil 3: Identifizierung und Quantifizierung
Emissions de sources fixes - Détermination de la concentration massique en
PCDDs/PCDFs - Partie 3: Identification et quantification
Ta slovenski standard je istoveten z: EN 1948-3:1996
ICS:
13.040.40 (PLVLMHQHSUHPLþQLKYLURY Stationary source emissions
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 14385:2025(Main)
Stationary source emissions - Determination of the total emission of As, Cd, Cr, Co, Cu, Mn, Ni, Pb, Sb, Tl and V
EN 14385:2024

This document specifies a manual reference method for the determination of the mass concentration of specific elements in stationary source emissions. The method is applicable to each of the specific elements in the concentration range of 0,005 mg/m3 to 5 mg/m3.
This document has been validated for the determination of the mass concentration of metals in incineration exhaust gases - applying the performance criteria stated in Clause 9 - for the following elements:
-   arsenic (As), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), manganese (Mn), nickel (Ni), lead (Pb), antimony (Sb), thallium (Tl), and vanadium (V) and their compounds.
The document can be used to determine metals other than those listed above (for example, selenium (Se) (ISO 17211), tellurium (Te), beryllium (Be), tin (Sn) and zinc (Zn)).
NOTE 1   These other metals mentioned above are commonly required by National Regulations, but this document currently has not yet been validated for these metals.
The document was validated for waste incinerators, but it is also applicable to other industrial processes, the practical experience shows that it can be applied over wide concentration ranges and various emission sources.
If mercury is intended to be determined as well, this can be sampled in a side stream arrangement of the sampling train (EN 13211) [5].
NOTE 2   This document has been validated with the described materials, equipment, sampling, and digestion performances etc., followed by analyses with atomic absorption spectroscopy (AAS) and inductively coupled plasma optical emission spectroscopy (ICP-OES,) or inductively coupled mass spectrometry (ICP-MS). This does not exclude the use of other types of equipment or analyses that meet the requirements and have been proven to be equivalent to the described European Standard.

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 7935:2025(Main)
Stationary source emissions - Determination of the mass concentration of sulfur dioxide in flue gases - Performance characteristics of automated measuring systems
ISO 7935:2024

This document specifies a method for the determination of sulfur dioxide (SO2) in flue gases of stationary
sources and describes the fundamental structure and the key performance characteristics of automated
measuring systems.
The method allows continuous monitoring with permanently installed measuring systems of SO2 emissions.
This document describes extractive systems and in situ (non-extractive) systems in connection with a range
of analysers that operate using, for example, the following principles:
— non-dispersive infrared absorption (NDIR);
— Fourier transform infrared (FTIR) spectroscopy;
— laser spectroscopic technique or tunable laser spectroscopy (TLS);
— non-dispersive ultraviolet absorption (NDUV);
— differential optical absorption spectroscopy (DOAS).
Other equivalent instrumental methods can be used provided they meet the minimum performance
requirements specified in this document. The measuring system can be validated with reference materials,
according to this document, or comparable methods.
Automated measuring system (AMS) based on the principles listed above has been used successfully in this
application for the measuring ranges as shown in Annex E.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    43 pages
    English language
    sale 15% off
SIST
SIST ISO 12141:2025(Main)
Stationary source emissions - Determination of low range mass concentration of dust - Manual gravimetric method
ISO 12141:2024

This document specifies the standard reference method (SRM) for the measurement of low dust
concentration in ducted gaseous streams in the concentrations below 50 mg/m3 at standard conditions.
This document is primarily developed and validated for gaseous streams emitted by waste incinerators. More
generally, it can be applied to gases emitted from other stationary sources, and to higher concentrations.
If the gases contain unstable, reactive or semi-volatile substances, the measurement depends on the
sampling and filter treatment conditions.
This method has been validated in field tests with special emphasis to dust concentrations around 5 mg/m3.
The results of the field tests are presented in Annex A.

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    53 pages
    English language
    sale 15% off
  • Standard
    59 pages
    French language
    sale 15% off
  • Standard
    59 pages
    French language
    sale 15% off
SIST
SIST-TS CEN/TS 18040:2024(Main)
Stationary source emissions - Determination of the mass concentration of formaldehyde - Automatic method
CEN/TS 18040:2024

This document specifies a measurement method based on an automatic method for determination of the mass concentration of formaldehyde in ducts and stacks emitting to the atmosphere. It specifies the sampling and gas conditioning system. Furthermore, it specifies the characteristics to be determined and the performance criteria to be fulfilled by portable automated measuring systems (P-AMS) using appropriate techniques to measure formaldehyde.
This method is intended for intermittent monitoring of formaldehyde emissions as well as for the calibration and validation of automated formaldehyde measuring systems.
The analyser is calibrated using test gases produced by a test gas generator.

  • Technical specification
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS 4207-2:2023
Emission measurements at small firing installations - Part 2: Measurements at installations for solid fuel (VDI 4207-2:2016, modified)

Ta tehnična specifikacija določa zahteve za prve, občasne in izredne meritve emisije iz malih kurilnih
naprav na trdna goriva v skladu s predpisom, ki ureja emisijo snovi v zrak iz malih kurilnih naprav, ter s
predpisom, ki ureja preglede, čiščenje in meritve pri malih kurilnih napravah. Tehnična specifikacija se
uporablja za ugotavljanje emisije, vključno z meritvami prahu, iz navedenih naprav. Poleg tega so
opisane tudi kontrolne aktivnosti, povezane z napravo in obratovanjem, ki morajo biti predhodno
izvedene, da se zagotovi ustrezen postopek merjenja emisije.
Dodatek A obravnava posebnosti pri kurilnih napravah na trdna goriva za ogrevanje posameznega
prostora, imenovanih enosobne male kurilne naprave.
Dodatek B vsebuje vzorec zapisnika o meritvah emisije na enosobnih malih kurilnih napravah.
Merila za razvrščanje enosobnih malih kurilnih naprav na trdna goriva so navedena v dodatku C.

  • Technical specification
    69 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 10849:2023(Main)
Stationary source emissions - Determination of the mass concentration of nitrogen oxides in flue gas - Performance characteristics of automated measuring systems
ISO 10849:2022

This document specifies a method for the determination of nitrogen oxides (NOx) in flue gas of stationary sources and describes the fundamental structure and the key performance characteristics of automated measuring systems.
The method allows continuous monitoring with permanently installed measuring systems of NOx emissions.
This document describes extractive systems and in situ (non-extractive) systems in connection with a range of analysers that operate using, for example, the following principles:
— chemiluminescence (CL);
— infrared absorption (NDIR);
— Fourier transform infrared (FTIR) spectroscopy;
— ultraviolet absorption (NDUV);
— differential optical absorption spectroscopy (DOAS);
Other equivalent instrumental methods such as laser spectroscopic techniques can be used provided they meet the minimum performance requirements specified in this document. The measuring system can be validated with reference materials, in accordance with this document, or comparable methods.
Automated measuring system (AMS) based on the principles listed above has been used successfully in this application for the measuring ranges as shown in Annex F.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 15% off
SIST
SIST ISO 20181:2023(Main)
Stationary source emissions - Quality assurance of automated measuring systems
ISO 20181:2023

This document was prepared by the European Committee for Standardization (CEN) as EN 14181:2014 and was adopted, without modification.
This document specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This document specifies:
— a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation;
— a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS, by checking that the zero and span characteristics are consistent with those determined during QAL1;
— a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined.
This document is designed to be used after the AMS has been certified in accordance with the series of documents EN 15267.

  • Standard
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    74 pages
    English language
    sale 15% off
SIST
SIST EN 17255-4:2023(Main)
Stationary source emissions - Data acquisition and handling systems - Part 4: Specification of requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems
EN 17255-4:2023

This document specifies the requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems (DAHS). This includes requirements on:
-   installation (Clause 5);
-   quality assurance and quality control during QAL2 (Clause 6);
-   quality assurance and quality control during on-going operation (Clause 7);
-   annual functional test (Clause 8);
-   documentation (Clause 9).
This document supports the requirements of EN 14181 and legislation such as the IED [1], MCPD [2] and E-PRTR [3]. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17911:2023(Main)
Stationary source emissions - Guideline for the elaboration of standardized measurement methods - Recommendations for the structure and content
CEN/TR 17911:2023

This document supports the elaboration of standardized measurement methods for the determination of stationary source emissions by manual or automated measurement methods.
This document describes the basic elements of standardized measurement methods for the determination of stationary source emissions.
This document is supplemented by an electronic template providing a uniform structure and common elements and texts.
NOTE   Detailed information on the electronic template is given in Annex A.
This document is addressed to working groups of CEN/TC 264 dealing with stationary source emissions. It aims at facilitating in the working groups the elaboration and the harmonization of documents produced by CEN/TC 264. Such documents can be European standards (EN), European Technical Specifications (CEN/TS) or European Technical Reports (CEN/TR).

  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14884:2023(Main)
Stationary source emissions - Determination of total mercury - Automated measuring systems
EN 14884:2022

This document specifies requirements for the calibration and validation (QAL2), the ongoing quality assurance during operation (QAL3) and the annual surveillance test (AST) of AMS used for monitoring total mercury emissions from stationary sources to demonstrate compliance with an emission limit value (ELV). This document is derived from EN 14181 and is only applicable in conjunction with EN 14181.
This document is applicable by direct correlation with the standard reference method (SRM) described in EN 13211.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day