SIST EN IEC 61189-5-504:2020

SLOVENSKI STANDARD
01-oktober-2020
Preskusne metode za električne materiale, tiskane plošče ter druge povezovalne
strukture in sestave - 5-504. del: Splošne preskusne metode za materiale in
sestave – Preskušanje procesa ionskega onesnaženja (PICT)
Test methods for electrical materials, printed boards and other interconnection structures
and assemblies - Part 5-504: General test methods for materials and assemblies -
Process ionic contamination testing (PICT)
Ta slovenski standard je istoveten z: EN IEC 61189-5-504:2020
ICS:
31.180 Tiskana vezja (TIV) in tiskane Printed circuits and boards
plošče
31.190 Sestavljeni elektronski Electronic component
elementi assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61189-5-504

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2020
ICS 31.180
English Version
Test methods for electrical materials, printed board and other
interconnection structures and assemblies - Part 5-504: General
test methods for materials and assemblies - Process ionic
contamination testing (PICT)
(IEC 61189-5-504:2020)
Méthodes d'essai pour les matériaux électriques, les cartes Prüfverfahren für Elektromaterialien, Leiterplatten und
imprimées et autres structures d'interconnexion et andere Verbindungsstrukturen und Baugruppen - Teil 5-
ensembles - Partie 5-504: Méthodes d'essai générales pour 504: Allgemeine Prüfverfahren für Materialien und
les matériaux et les ensembles - Essai de contamination Baugruppen - Prüfung der ionischen Verunreinigung bei
ionique des procédés (PICT) Prozessen (PICT)
(IEC 61189-5-504:2020) (IEC 61189-5-504:2020)
This European Standard was approved by CENELEC on 2020-05-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61189-5-504:2020 E

European foreword
The text of document 91/1639/FDIS, future edition 1 of IEC 61189-5-504, prepared by IEC/TC 91
"Electronics assembly technology" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61189-5-504:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-02-26
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-26
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61189-5-504:2020 was approved by CENELEC as a
European Standard without any modification.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General and EN 60068-1 -
guidance
IEC 60068-2-20 - Environmental testing - Part 2-20: Tests - EN 60068-2-20 -
Test T: Test methods for solderability and
resistance to soldering heat of devices with
leads
IEC 60068-2-58 - Environmental testing - Part 2-58: Tests - EN 60068-2-58 -
Test Td: Test methods for solderability,
resistance to dissolution of metallization
and to soldering heat of surface mounting
devices (SMD)
IEC 60079-7 - Explosive atmospheres - Part 7: Equipment EN 60079-7 -
protection by increased safety "e"
IEC 60194 - Printed board design, manufacture and - -
assembly - Terms and definitions
IEC 61189-5-502 - Test methods for electrical materials, - -
printed boards and other interconnection
structures and assemblies - Part 5-502:
General test methods for materials and
assemblies - Surface insulation resistance
(SIR) testing of assemblies
IEC 61190-1-3 - Attachment materials for electronic EN IEC 61190-1-3 -
assembly - Part 1-3: Requirements for
electronic grade solder alloys and fluxed
and non-fluxed solid solder for electronic
soldering applications
IPC-TM-650 - Surface Insulation Resistance - -
method 2.6.3.7
IPC 9202 - Material and Process Characterisation / - -
Qualification Test Protocol for Assessing
Electrochemical Performance
IPC 9203 - Users Guide to IPC 9202 and the IPC-B-52 - -
Standard Test Vehicle
IEC 61189-5-504 ®
Edition 1.0 2020-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Test methods for electrical materials, printed board and other interconnection

structures and assemblies –
Part 5-504: General test methods for materials and assemblies – Process ionic

contamination testing (PICT)
Méthodes d'essai pour les matériaux électriques, les cartes imprimées et autres

structures d'interconnexion et ensembles –

Partie 5-504: Méthodes d'essai générales pour les matériaux et les ensembles –

Essai de contamination ionique des procédés (PICT)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.180 ISBN 978-2-8322-8111-6

– 2 – IEC 61189-5-504:2020  IEC 2020
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General description of the test . 7
5 Test apparatus . 7
6 Materials . 8
6.1 Test solution . 8
6.1.1 General . 8
6.1.2 Deionised water (DI) . 8
6.1.3 Propan-2-ol . 9
6.2 Calibration solution . 9
6.3 Test chamber . 9
6.4 Regeneration filter column . 9
6.5 Recirculating pump . 9
6.6 Measurement system capability . 9
7 Test procedure . 9
7.1 Test apparatus . 9
7.2 Closed loop . 10
7.3 Open loop . 11
7.4 System verification . 12
7.4.1 General . 12
7.4.2 Polishing the test solution . 12
7.4.3 Recording test solution temperature and specific gravity. 12
7.4.4 Checking conductivity accuracy . 13
7.5 Procedure . 14
7.5.1 Specimen handling . 14
7.5.2 General . 14
7.5.3 Closed loop . 14
7.5.4 Open loop . 15
7.5.5 Influence of CO . 15
8 Measurement Methods . 16
8.1 Method 1. 16
8.2 Method 2. 17
Annex A (normative) Test technique . 18
A.1 Conductivity signal . 18
A.2 DI water correction . 18
A.3 Conductivity of the ionic solution . 19
A.3.1 General . 19
A.3.2 Conductivity differences. 20
A.4 Test solution temperature . 20
A.4.1 General . 20
A.4.2 Linear temperature . 20
A.4.3 Leaching effects . 20
A.5 Conversion of conductivity to contamination . 21
A.6 Calibration . 21

IEC 61189-5-504:2020  IEC 2020 – 3 –
Annex B (informative) Measurement methods . 22
B.1 Method 1. 22
B.2 Method 2. 24
Bibliography . 25

Figure 1 – Typical test instrument . 8
Figure 2 – Closed-loop method in regeneration mode . 10
Figure 3 – Closed loop in test mode . 11
Figure 4 – Open loop method . 12
Figure 5 – 50 % specific gravity chart . 13
Figure 6 – 75 % specific gravity chart . 13
Figure 7 – Example of result measuring the influence of CO . 16
Figure A.1 – Conductivity against voltage curve . 18
Figure A.2 – Deionised water correction. 19
Figure B.1 – Test pass . 23
Figure B.2 – Test fail . 23

Table B.1 – Pass/Fail value method 1 worked example . 22

– 4 – IEC 61189-5-504:2020  IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARDS
AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES –

Part 5-504: General test methods for materials and assemblies –
Process ionic contamination testing (PICT)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61189-5-504 has been prepared by IEC technical committee 91:
Electronics assembly technology.
The text of this International Standard is based on the following documents:
FDIS Report on voting
91/1639/FDIS 91/1644/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

IEC 61189-5-504:2020  IEC 2020 – 5 –
A list of all parts in the IEC 61189 series, published under the general title Test methods for
electrical materials, printed boards and other interconnection structures and assemblies, can
be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
– 6 – IEC 61189-5-504:2020  IEC 2020
TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARDS
AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES –

Part 5-504: General test methods for materials and assemblies –
Process ionic contamination testing (PICT)

1 Scope
This part of IEC 61189 is a test method designed to determine the proportion of soluble ionic
residues present upon a circuit board, electronic component or assembly. The conductivity of
the solution used to dissolve the ionic residues is measured to evaluate the level of ionic
residues.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60068-1, Environmental testing – General and guidance
IEC 60068-2-20, Environmental testing – Part 2-20: Tests – Test T: Test methods for
solderability and resistance to soldering heat of devices with leads
IEC 60068-2-58, Environmental testing – Part 2-58: Tests – Test Td: Test methods for
solderability, resistance to dissolution of metallization and to soldering heat of surface
mounting devices (SMD)
IEC 60079-7, Explosive atmospheres – Part 7: Equipment protection by increased safety "e"
IEC 60194, Printed board design, manufacture and assembly – Terms and definitions
IEC 61189-5-502, Test methods for electrical materials, printed boards and other
interconnection structures and assemblies – Part 5-502: General test methods for materials
and assemblies – Surface insulation resistance (SIR) testing of assemblies
IEC 61190-1-3, Attachment materials for electronic assembly – Part 1-3: Requirements for
electronic grade solder alloys and fluxed and non-fluxed solid solder for electronic soldering
applications
IPC-TM-650 method 2.6.3.7, Surface Insulation Resistance
IPC 9202, Material and Process Characterisation / Qualification Test Protocol for Assessing
Electrochemical Performance
IPC 9203, Users Guide to IPC 9202 and the IPC-B-52 Standard Test Vehicle

IEC 61189-5-504:2020  IEC 2020 – 7 –
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60068-1,
IEC 60068-2-20:2008, IEC 60068-2-58, IEC 60194, and IEC 61190-1-3 apply.
4 General description of the test
The test measures the conductivity of a test solution that comprises a mixture of de-ionised
water and alcohol (propan-2-ol). The test equipment shall measure the total current flow and
the result shall be expressed as an equivalence of sodium chloride (NaCl) mass per unit area
(μg/cm ≡ NaCl).
The test is used
...