SIST EN 16474:2015
(Main)Plastics and rubber machines - Tyre curing presses - Safety requirements
Plastics and rubber machines - Tyre curing presses - Safety requirements
This European Standard applies to tyre curing machines having the following configuration.
- crossing flow tyre curing machines, with two cavities with:
- common curing cycle and common safeguarding; or
- independent curing cycles and common safeguarding; or
- independent curing cycles and independent safeguarding.
- tyre curing machines with one cavity.
- tyre curing machines with automatic rear feeding and discharge.
The safety requirements and/or protective measures specified in this European Standard apply to tyre curing machines for passenger vehicle tyres and truck tyres.
This European Standard does not deal with:
- feeding system and discharge system;
- tyre curing machines with manual loading of the green tyre into the mould and manual unloading of the cured tyre from the mould;
- ancillary equipment which is not an integral part of the tyre curing machine, e.g. conveying equipment;
- exhaust systems.
This European Standard deals with all significant hazards, hazardous situations and events relevant to tyre curing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
It does not deal with hazards associated with falling of parts of the container or mould.
Some tyre curing machines include pressure vessels, which fall under Directive 97/23/EC [1]; this European standard is not intended to support the Directive 97/23/EC.
This European Standard is not applicable to tyre curing machines which are manufactured before the date of its publication as an EN.
Hazard associated with falling of parts of the container or mould are not covered by this European Standard.
Safety requirements relating to the design of ancillary equipment which is not an integral part of the tyre curing press, e.g. conveying equipment are not covered in this European Standard.
Safety requirements relating the design of exhaust systems are not covered in this European Standard.
This European Standard covers the significant hazards listed in Clause 4.
NOTE This European Standard is not intended to support the PED [1]. For pressure hazards, see informative Annex A.
This document is not applicable to tyre curing presses which are manufactured before the date of its publication as EN.
Kunststoff- und Gummimaschinen - Reifenheizpressen - Sicherheitsanforderungen
Diese Europäische Norm gilt für Reifenheizpressen1), wie in 3.36 definiert, mit der folgenden Konfiguration:
- Kreuzstrom-Reifenheizpressen mit zwei Kavitäten mit:
- gemeinsamem Heizzyklus und gemeinsamer Absicherung; oder
- voneinander unabhängigen Heizzyklen und gemeinsamer Absicherung; oder
- voneinander unabhängigen Heizzyklen und unabhängiger Absicherung;
- Reifenheizpressen mit einer Kavität;
- Reifenheizpressen mit automatischer rückseitiger Beschickung und Entnahme.
Die in dieser Norm festgelegten Sicherheitsanforderungen und/oder Schutzmaßnahmen gelten für Reifenheizpressen für Reifen für Personenkraftwagen und Lastkraftwagen.
In dieser Norm sind nur das automatische Reifenbeschicken in die Form und die automatische Reifenentnahme aus der Form behandelt.
Beschickungssysteme und Entnahmesysteme sind in dieser Europäischen Norm nicht behandelt.
Gefährdungen in Verbindungen mit dem Herabfallen von Teilen des Containers oder der Form sind in dieser Europäischen Norm nicht behandelt.
Sicherheitsanforderungen, die sich auf die Konzipierung von Zusatzeinrichtungen beziehen, die nicht Bestandteil der Reifenheizpresse sind, z. B. Fördereinrichtungen, sind in dieser Europäischen Norm nicht behandelt.
Sicherheitsanforderungen an die Konzipierung von Absaugsystemen sind in dieser Europäischen Norm nicht behandelt.
Diese Europäische Norm behandelt die in Abschnitt 4 gelisteten signifikanten Gefährdungen.
ANMERKUNG Diese Europäische Norm ist nicht dafür vorgesehen, die Druckgeräterichtlinie zu erfüllen. Für die Gefährdungen durch Druck, siehe informativer Anhang A.
Dieses Dokument gilt nicht für Reifenheizpressen, die vor dem Datum der Veröffentlichung als EN hergestellt worden sind.
Machines pour les matières plastiques et le caoutchouc - Presses à vulcaniser - Prescriptions de sécurité
La présente Norme européenne s’applique aux machines à vulcaniser les pneumatiques dont la configuration
est la suivante :
Machines à vulcaniser les pneumatiques à flux traversant, à deux cavités avec :
un cycle de vulcanisation commun et des mesures de protection communes ; ou
des cycles de vulcanisation indépendants et des mesures de protection communes ; ou
des cycles de vulcanisation indépendants et des mesures de protection indépendantes.
Machines à vulcaniser les pneumatiques à une cavité.
Machines à vulcaniser les pneumatiques à alimentation et évacuation automatiques par l’arrière.
Les prescriptions de sécurité et/ou mesures de prévention spécifiées dans la présente Norme européenne
s’appliquent aux machines à vulcaniser les pneumatiques des véhicules de tourisme et des véhicules poids
lourds.
La présente Norme européenne ne traite pas :
du système d’alimentation ni du système d’évacuation de la machine ;
des machines à vulcaniser les pneumatiques avec chargement manuel du bandage dans la moule et
déchargement de l'enveloppe du moule
des équipements auxiliaires qui ne font pas partie intégrante de la machine à vulcaniser, tels que les
équipements de convoyage.
des systèmes d'assainissement de l’air par aspiration.
Le présent document traite de tous les phénomènes dangereux, situations et événements dangereux
significatifs associés aux machines à vulcaniser les pneumatiques en cas d’utilisation normale ou de mauvais
usage raisonnablement prévisible par le constructeur (voir l’Article 4).
La présente Norme européenne ne traite pas des phénomènes dangereux associés à la chute de pièces du
container ou du moule.
Certaines machines à vulcaniser les pneumatiques relèvent de la directive 97/23/CE [1] ; Il n’est pas prévu
que la présente Norme européenne vienne à l’appui de la directive 97/23/CE.
La présente Norme européenne n’est pas applicable aux machines à vulcaniser les pneumatiques fabriquées
avant sa date de publication comme EN.
Stroji za predelavo gume in plastike - Stiskalnice za vulkaniziranje - Varnostne zahteve
General Information
Relations
Overview
SIST EN 16474:2015 - Plastics and rubber machines: Tyre curing presses - Safety requirements defines safety requirements for tyre curing machines (tyre curing presses) used for vulcanisation of passenger‑vehicle and truck tyres. It applies to common configurations including:
- crossing‑flow machines with two cavities (common or independent curing cycles and safeguarding),
- single‑cavity machines, and
- machines with automatic rear feeding and discharge.
This European (type C) standard addresses significant hazards when machines are used as intended or under reasonably foreseeable misuse. It supports the essential requirements of EU Directive 2006/42/EC but is not intended to support the Pressure Equipment Directive (PED, Directive 97/23/EC). SIST EN 16474:2015 is not applicable to machines manufactured before its EN publication date.
Key topics and technical requirements
The standard sets out safety measures and verification for tyre curing presses, covering:
- List of significant hazards (Clause 4) relevant to curing presses.
- General and specific safety requirements (Clause 5) for production mode and other operations, including guarding, interlocks and control functions.
- Emergency stop function principles and requirements.
- Noise reduction and declaration: identification of main noise sources, design measures to reduce noise, and Annex A noise test code for measurement and reporting.
- Verification procedures to confirm safety measures are implemented (Clause 6).
- Information for use (Clause 7): instruction handbook content, marking, warnings, maintenance, and operator information (hot surfaces, curing media leakage, nitrogen, etc.).
- Interaction with safety‑related control systems, electro‑sensitive protective devices, hydraulics/pneumatics and electrical equipment through referenced standards.
What is explicitly excluded:
- feeding and discharge systems, manual loading/unloading machines, ancillary equipment not integral to the press (e.g., conveyors), exhaust systems, and hazards from falling parts of containers/moulds.
Practical applications - who uses this standard
SIST EN 16474:2015 is essential for:
- Machine manufacturers and designers for safe design, guarding, and control strategies of tyre curing presses.
- Safety engineers and compliance officers preparing risk assessments and conformity documentation for CE marking under the Machinery Directive.
- Plant managers, maintenance teams and operators to understand required warnings, maintenance procedures and emergency functions.
- Test laboratories and certification bodies verifying noise emissions and safety features.
- Purchasers and integrators specifying safe tyre curing equipment.
Keywords: tyre curing presses, tyre curing machines, safety requirements, SIST EN 16474:2015, vulcanisation, machine safety, noise emission, Machinery Directive.
Related standards
SIST EN 16474:2015 references many normative standards such as EN ISO 12100 (risk assessment), EN ISO 13849‑1 (safety‑related control systems), EN 60204‑1 (electrical safety), EN ISO standards for acoustics and for hydraulics/pneumatics among others. These provide detailed technical methods aligned with the safety requirements in EN 16474.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stroji za predelavo gume in plastike - Stiskalnice za vulkaniziranje - Varnostne zahteveKunststoff- und Gummimaschinen - Reifenheizpressen - SicherheitsanforderungenMachines pour les matières plastiques et le caoutchouc - Presses à vulcaniser - Prescriptions de sécuritéPlastics and rubber machines - Tyre curing presses - Safety requirements83.200Oprema za gumarsko industrijo in industrijo polimernih materialovEquipment for the rubber and plastics industries25.120.10Kovaški stroji. Stiskalnice. ŠkarjeForging equipment. Presses. ShearsICS:Ta slovenski standard je istoveten z:EN 16474:2015SIST EN 16474:2015en,fr,de01-julij-2015SIST EN 16474:2015SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16474
April 2015 ICS 83.200 English Version
Plastics and rubber machines - Tyre curing machines - Safety requirements
Machines pour les matières plastiques et le caoutchouc - Machines à vulcaniser les pneumatiques - Prescriptions de sécurité
Kunststoff- und Gummimaschinen - Reifenvulkanisiermaschinen - Sicherheitsanforderungen This European Standard was approved by CEN on 10 October 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16474:2015 ESIST EN 16474:2015
Noise test code . 65 A.1 Introduction . 65 A.2 Measurement of the A-weighted emission sound pressure level at the operator’s or other specified positions . 65 A.2.1 Basic standards . 65 SIST EN 16474:2015
Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC . 70 Bibliography . 71
See Figure 1 and Figure 2. 3.2 crossing flow machine type in which green tyres are fed and loaded from the front and cured tyres are unloaded and discharged from the rear 3.3 cavity part of the machine in which the container and/or the mould and the bladder are installed 3.4 green tyre assembly of rubber parts intended to be cured 3.5 cured tyre tyre in its final form after vulcanisation SIST EN 16474:2015
Key 1 container 2 top ring 3 bottom ring 4 bladder 5 heating platen Figure 1 — Main parts of tyre curing machines (front view) SIST EN 16474:2015
Key 1 unloading device 2 take-away conveyor 3 green tyre stand 4 top ring 5 green tyre 6 loading device 7 chuck 8 movable upper part 9 cured tyre Figure 2 — Main parts of tyre curing machines (side view) 4 List of significant hazards 4.1 General This clause contains all the significant hazards, hazardous situations and events identified by risk assessment as significant for this type of machinery and which require action to eliminate or reduce the risk. For the location of hazards on crossing flow tyre curing machines, see Figure 3, Figure 4 and Figure 5. SIST EN 16474:2015
Figure 3 — Location of hazards on crossing flow tyre curing machines (front view) SIST EN 16474:2015
Figure 4 — Location of hazards on crossing flow tyre curing machines (side view) SIST EN 16474:2015
Figure 5 — Location of hazards on crossing flow tyre curing machines (top view) SIST EN 16474:2015
Figure 6 — Location of hazards on tyre curing machines with automatic rear feeding and discharge (front view) SIST EN 16474:2015
Figure 7 — Location of hazards on tyre curing machines with automatic rear feeding and discharge (side view) SIST EN 16474:2015
Figure 8 — Location of hazards on tyre curing machines with automatic rear feeding and discharge (top view) 4.2 General hazards Electric shock or burns due to direct or indirect contact with live conductive parts (see 5.1). Hazards due to malfunction of the hydraulic or pneumatic systems (see 5.1). Hazards from high noise levels resulting for example in hearing impairment, tiredness, stress, loss of balance or awareness, interference with speech communications or with the perception of acoustic signals (see 5.4). Hazards due to neglecting ergonomic principles, e.g. musculoskeletal disorders due to posture, efforts and/or repetitive activity related to manual feeding of green tyres (see 5.1). 4.3 Hazards associated with specific machine parts or areas The significant hazards associated with specific parts or areas of tyre curing machines are the following: SIST EN 16474:2015
Key 1 front position 2 rear position 3 side position Key 1 front position 2 rear position 3 side position Figure 9 — Positions on crossing flow tyre curing machines Figure 10 — Position on tyre curing machine with automatic rear feeding and discharge .
Where these safeguards cannot be practically implemented, e.g. due to lack of space, pressure sensitive bumpers in accordance with EN ISO 13856-3:2013 may be installed under the following conditions: — the pressure sensitive bumper shall be dimensioned and positioned so that the dangerous moving part has stopped before any injury can occur and that nobody can stand between the pressure sensitive bumper and crushing/shearing points; — if the pressure sensitive bumper is adjustable, its safe position with respect to the size of the container and mould shall be detected by the safety related parts of the control system of the machine before the movement can be started. d Interlocking guard with or without guard locking. d for the safeguar-ding function c only for the stopping function of the downward movement in case of use of the interlocking guard with guard locking Position 2: rear Fixed distance guard and/or Take-away conveyor, acting as a fixed distance guard. Interlocking guard with guard locking for the feeding/discharge system and/or Interlocking guard without guard locking associated with light curtains. Position 3: side Fixed distance guard and interlocking guard with or without guard locking or Combination of fixed distance guards and machine parts acting as fixed guards preventing access. Fixed distance guard. SIST EN 16474:2015
Where these safeguards cannot be practically implemented, e.g. due to lack of space, pressure sensitive bumpers in accordance with EN ISO 13856-3:2013 may be installed under the following conditions : — the pressure sensitive bumper shall be dimensioned and positioned so that the dangerous moving part has stopped before any injury can occur and that nobody can stand between the pressure sensitive bumper and crushing/shearing points; — if the pressure sensitive bumper is adjustable, its safe position with respect to the size of the loading device and/or green tyre stand shall be detected by the safety related parts of the control system of the machine before the movement can be started. d Interlocking guard with or without guard locking. d Position 2: rear Fixed distance guard and/or Take-away conveyor, acting as a fixed distance guard. Interlocking guard with guard locking for the feeding/discharge system. Position 3: side Fixed distance guard and interlocking guard with or without guard locking or Combination of fixed distance guards and machine parts acting as fixed guards preventing access. Fixed distance guard. SIST EN 16474:2015
...
Frequently Asked Questions
SIST EN 16474:2015 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Plastics and rubber machines - Tyre curing presses - Safety requirements". This standard covers: This European Standard applies to tyre curing machines having the following configuration. - crossing flow tyre curing machines, with two cavities with: - common curing cycle and common safeguarding; or - independent curing cycles and common safeguarding; or - independent curing cycles and independent safeguarding. - tyre curing machines with one cavity. - tyre curing machines with automatic rear feeding and discharge. The safety requirements and/or protective measures specified in this European Standard apply to tyre curing machines for passenger vehicle tyres and truck tyres. This European Standard does not deal with: - feeding system and discharge system; - tyre curing machines with manual loading of the green tyre into the mould and manual unloading of the cured tyre from the mould; - ancillary equipment which is not an integral part of the tyre curing machine, e.g. conveying equipment; - exhaust systems. This European Standard deals with all significant hazards, hazardous situations and events relevant to tyre curing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). It does not deal with hazards associated with falling of parts of the container or mould. Some tyre curing machines include pressure vessels, which fall under Directive 97/23/EC [1]; this European standard is not intended to support the Directive 97/23/EC. This European Standard is not applicable to tyre curing machines which are manufactured before the date of its publication as an EN. Hazard associated with falling of parts of the container or mould are not covered by this European Standard. Safety requirements relating to the design of ancillary equipment which is not an integral part of the tyre curing press, e.g. conveying equipment are not covered in this European Standard. Safety requirements relating the design of exhaust systems are not covered in this European Standard. This European Standard covers the significant hazards listed in Clause 4. NOTE This European Standard is not intended to support the PED [1]. For pressure hazards, see informative Annex A. This document is not applicable to tyre curing presses which are manufactured before the date of its publication as EN.
This European Standard applies to tyre curing machines having the following configuration. - crossing flow tyre curing machines, with two cavities with: - common curing cycle and common safeguarding; or - independent curing cycles and common safeguarding; or - independent curing cycles and independent safeguarding. - tyre curing machines with one cavity. - tyre curing machines with automatic rear feeding and discharge. The safety requirements and/or protective measures specified in this European Standard apply to tyre curing machines for passenger vehicle tyres and truck tyres. This European Standard does not deal with: - feeding system and discharge system; - tyre curing machines with manual loading of the green tyre into the mould and manual unloading of the cured tyre from the mould; - ancillary equipment which is not an integral part of the tyre curing machine, e.g. conveying equipment; - exhaust systems. This European Standard deals with all significant hazards, hazardous situations and events relevant to tyre curing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). It does not deal with hazards associated with falling of parts of the container or mould. Some tyre curing machines include pressure vessels, which fall under Directive 97/23/EC [1]; this European standard is not intended to support the Directive 97/23/EC. This European Standard is not applicable to tyre curing machines which are manufactured before the date of its publication as an EN. Hazard associated with falling of parts of the container or mould are not covered by this European Standard. Safety requirements relating to the design of ancillary equipment which is not an integral part of the tyre curing press, e.g. conveying equipment are not covered in this European Standard. Safety requirements relating the design of exhaust systems are not covered in this European Standard. This European Standard covers the significant hazards listed in Clause 4. NOTE This European Standard is not intended to support the PED [1]. For pressure hazards, see informative Annex A. This document is not applicable to tyre curing presses which are manufactured before the date of its publication as EN.
SIST EN 16474:2015 is classified under the following ICS (International Classification for Standards) categories: 25.120.10 - Forging equipment. Presses. Shears; 83.200 - Equipment for the rubber and plastics industries. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 16474:2015 has the following relationships with other standards: It is inter standard links to SIST EN 16474:2026, SIST EN 16474:2026. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 16474:2015 is associated with the following European legislation: EU Directives/Regulations: 2006/42/EC; Standardization Mandates: M/BC/CEN/88/13. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 16474:2015 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
この記事は、「SIST EN 16474:2015 - プラスチックおよびゴム機械 - タイヤ成形プレス - 安全要件」というタイトルであり、タイヤ成形プレスに関する安全要件について述べています。この欧州規格は、以下の構成を持つタイヤ成形プレスに適用されます。 - 2つのキャビティを持つクロスフロータイヤ成形プレス：共通の成形サイクルと共通の安全対策、または独立した成形サイクルと共通の安全対策、または独立した成形サイクルと独立した安全対策を持つもの。 - 1つのキャビティを持つタイヤ成形プレス。 - 自動的な後部給与および排出機能を持つタイヤ成形プレス。 この欧州規格で規定される要件および安全対策は、乗用車用およびトラック用タイヤのタイヤ成形プレスに適用されます。この規格はタイヤの自動的な積み込みおよび降ろし込みにのみ適用され、給与システムや排出システム、および容器や金型の部品落下に関連する危険は含まれません。また、タイヤ成形プレスの一部であるコンベア装置などの補助装置の設計に関連する安全要件も含まれません。排気システムの設計に関連する安全要件も含まれません。この欧州規格は、PED（圧力機器指令）をサポートするために意図されているわけではなく、圧力の危険については補足的な付録Aを参照するように注意書きがあります。本文書は、ENとして発行された後に製造されたタイヤ成形プレスに適用されます。
The article discusses the safety requirements for tyre curing presses. It specifically applies to different configurations of these machines, such as crossing flow presses with two cavities, presses with one cavity, and presses with automatic rear feeding and discharge. The safety requirements outlined in this European standard are for tyre curing presses used for passenger vehicle tyres and truck tyres. The standard only covers automatic loading and unloading of tyres, and does not include requirements for the feeding system, discharge system, or hazards related to falling parts of the container or mould. It also does not cover safety requirements for ancillary equipment or exhaust systems. The article specifies that it is not intended to support the PED (Pressure Equipment Directive), and is only applicable to tyre curing presses manufactured after its publication as EN.
The article discusses the safety requirements for tyre curing presses according to the SIST EN 16474:2015 standard. The standard applies to various types of presses, including crossing flow presses with one or two cavities, presses with automatic feeding and discharge, and presses with one cavity. The standard focuses on the safety measures for passenger vehicle and truck tyre presses, specifically covering automatic loading and unloading of tyres. However, it does not cover the design of the feeding and discharge systems, hazards related to falling parts, design of ancillary equipment, or exhaust systems. The article mentions that the standard does not support the PED and is not applicable to presses manufactured before its publication.
記事のタイトル：SIST EN 16474:2015 - プラスチックとゴムの機械 - タイヤ成形プレス - 安全要件 記事の内容：このヨーロッパ規格は、以下の構成を持つタイヤ成形プレスに適用されます。 - 2つのキャビティを持つ交差流れタイヤ成形プレス： - 共通の成形サイクルと共通の安全対策または - 独立した成形サイクルと共通の安全対策または - 独立した成形サイクルと独立した安全対策 - 1つのキャビティを持つタイヤ成形プレス - 自動的な後部給与および排出機能を備えたタイヤ成形プレス このヨーロッパ規格では、乗用車用タイヤおよびトラック用タイヤの成形プレスに適用される要件および安全対策が指定されています。 このヨーロッパ規格は、金型への自動的なタイヤの積み込みおよび自動的な積み下ろしにのみ適用されます。 給与システムおよび排出システムは、このヨーロッパ規格では扱われていません。 容器や金型の部品の落下に関連する危険は、このヨーロッパ規格では扱われていません。 輸送装置など、タイヤ成形プレスの本体ではない付属装置の設計に関連する安全要件は、このヨーロッパ規格では扱われていません。 排気システムの設計に関連する安全要件は、このヨーロッパ規格では扱われていません。 このヨーロッパ規格は、4節にリストされた重要な危険をカバーしています。 注：このヨーロッパ規格はPEDをサポートするためのものではありません。圧力に関連する危険については、参考付録Aを参照してください。 この文書は、ENとして出版される前に製造されたタイヤ成形プレスには適用されません。
해당 기사는 "SIST EN 16474:2015 - 플라스틱 및 고무 기계 - 타이어 경화 프레스 - 안전 요구사항"이라는 제목을 가지고 있습니다. 이 유럽 표준은 다음과 같은 구성을 가진 타이어 경화 프레스에 적용됩니다. - 2개의 구동순환구와 함께하는 횡단 유동 타이어 경화 프레스. - 공통 경화 순환구 및 공통 보호장치를 가지는 경우 - 독립적인 경화 순환구 및 공통 보호장치를 가지는 경우 - 독립적인 경화 순환구 및 독립 보호장치를 가지는 경우 - 하나의 구동순환구를 가지는 타이어 경화 프레스 - 후면 자동 공급 및 배출 기능을 가지는 타이어 경화 프레스 이 유럽 표준에서 규정된 요구사항 및 안전조치는 승용차 타이어와 트럭 타이어용 타이어 경화 프레스에 적용됩니다. 이 유럽 표준은 타이어의 자동 적재 및 자동 탈산만을 다루며, 공급 시스템 및 배출 시스템, 그리고 컨테이너나 금형 부품이 떨어지는 등의 위험은 해당되지 않습니다. 또한, 이 유럽 표준은 운송장비와 같은 타이어 경화 프레스의 일부분이 아닌 부속 장비의 설계에 관련된 안전 요구사항을 다루지 않습니다. 또한 배출 시스템의 설계와 관련된 안전 요구사항도 다루지 않습니다. 이 유럽 표준은 “PED”를 지원하기 위한 것이 아니며, 압력 위험에 대해서는 부록을 참조하라고 별도로 언급되어 있습니다. 본 문서는 EN으로 발행된 이후에 제작된 타이어 경화 프레스에만 적용됩니다.
기사 제목: SIST EN 16474: 2015 - 플라스틱 및 고무 기계 - 타이어 가공 프레스 - 안전 요구 사항 기사 내용: 이 유럽 표준은 다음과 같은 구성을 갖는 타이어 가공 프레스에 적용됩니다. - 2개의 캐비티를 가진 교차 유량 타이어 가공 프레스: - 공통 가공 주기와 공통 안전장치가있는 경우 또는 - 독립적인 가공 주기와 공통 안전장치가있는 경우 또는 - 독립적인 가공 주기와 독립적인 안전장치가 있는 경우 - 한 개의 캐비티를 가진 타이어 가공 프레스 - 후방 자동 급여 및 배출 기능이있는 타이어 가공 프레스 이 유럽 표준에서는 승용차 타이어 및 트럭 타이어에 대한 타이어 가공 프레스에 적용되는 요구 사항 및 안전 조치가 지정되어 있습니다. 이 유럽 표준은 금형에 대한 타이어의 자동로딩 및 자동 언로딩에만 적용됩니다. 급여 시스템과 배출 시스템은 이 유럽 표준에서 다루지 않습니다. 컨테이너 또는 금형의 부품이 떨어지는 위험은 이 유럽 표준에서 다루지 않습니다. 이 유럽 표준에는 컨베이어 장비와 같이 타이어 가공 프레스의 본질적인 부분이 아닌 보조 장비의 설계에 관련된 안전 요구 사항은 다루지 않습니다. 배기 시스템의 설계에 관련된 안전 요구 사항은 이 유럽 표준에서 다루지 않습니다. 이 유럽 표준은 4절에서 목록화 된 주요 위험 사항을 다룹니다. 참고: 이 유럽 표준은 PED[1]을 지원하기 위한 것이 아닙니다. 압력 위험에 대해서는 부록 A를 참조하십시오. 본 문서는 EN으로 출판되기 전에 제조된 타이어 가공 프레스에는 적용되지 않습니다.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...