oSIST prEN 10370:2019
(Main)Steel for the reinforcement of concrete - Stainless steel
Steel for the reinforcement of concrete - Stainless steel
This document specifies product characteristic, test/assessment method and the way of expressing test results, for stainless steel as defined in EN 10088-1 and designated as in EN 10088-1 for the use of the reinforcement of concrete.
It applies to stainless steel products with ribbed or indented surfaces, which are in the form of:
- bars and coils (rod, wire);
- sheets of factory-made machine-welded fabric;
- lattice girders and hybrid lattice girders composed by stainless steel and by weldable reinforcing steel according to EN 10080.
This document does not apply to:
- pre-stressed stainless steels;
- indented strip;
- stainless steel tube filled with carbon steel swarf, which is then hot or cold reduced;
- stainless steel smooth bar with weld material deposited on it;
- galvanized reinforcing steel;
- epoxy-coated reinforcing steel.
Stahl für die Bewehrung von Beton - Nichtrostender Stahl
Diese Europäische Norm legt Leistungsmerkmale, Prüfung und Bewertung von Prüfergebnissen von nichtrostendem Stahl definiert und bezeichnet nach EN 10088-1 fest, der für die Bewehrung von Betonbauwerken verwendet wird. Stähle nach dieser Europäischen Norm haben eine gerippte oder profilierte Oberfläche und werden geliefert in Form von:
- Stäben, Ringen (Walzdraht, Draht);
- werkmäßig gefertigten maschinell geschweißten Matten;
- Gitterträgern und hybriden Gitterträgern, hergestellt aus nichtrostendem Stahl und Schweißgeeignetem Betonstahl nach EN 10080.
Diese Europäische Norm gilt nicht für
- nichtrostende Stähle für Vorspannen;
- profiliertes Band;
- nichtrostende Stahlrohre gefüllt mit unlegiertem Stahl , anschließend warm- oder kalt abgelängt;
- geschweißte nichtrostende Stäbe aus Stahl mit glatter Oberfläche;
- verzinkten Betonstahl;
- epoxidbeschichteten Betonstahl.
Aciers pour l'armature du béton - Aciers inoxydables
Le présent document spécifie les caractéristiques des produits, la méthode d’essai et d’évaluation ainsi que le mode d’expression des résultats de l'essai, pour les aciers inoxydables définis dans l’EN 10088-1 et désignés dans l’EN 10088-1 pour l’utilisation dans l’armature du béton.
Il s’applique aux produits en acier inoxydable présentant une surface avec des verrous ou des empreintes sous la forme de :
- barres et couronnes (fil machine, fil) ;
- panneaux de treillis soudés sur machine, fabriqués en usine ;
- treillis raidisseurs et treillis raidisseurs hybrides composés d’aciers inoxydables et d’aciers soudables pour béton armé conformément à l’EN 10080.
Le présent document ne s’applique pas :
- aux armatures de précontrainte en acier ;
- aux feuillards crantés ;
- aux tubes d’acier inoxydable remplis de copeaux d’acier au carbone, qui sont ensuite réduits à chaud ou à froid ;
- aux barres d’acier inoxydable lisses avec matériau soudé déposé dessus ;
- aux aciers pour béton armé galvanisés ;
- aux aciers pour béton armé avec revêtement époxy.
Jekla za armiranje betona - Nerjavno jeklo
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 10370:2019
01-julij-2019
Jekla za armiranje betona - Nerjavno jeklo
Steel for the reinforcement of concrete - Stainless steel
Stahl für die Bewehrung von Beton - Nichtrostender Stahl
Aciers pour l'armature du béton - Aciers inoxydables
Ta slovenski standard je istoveten z: prEN 10370
ICS:
77.140.15 Jekla za armiranje betona Steels for reinforcement of
concrete
77.140.20 Visokokakovostna jekla Stainless steels
oSIST prEN 10370:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10370:2019
---------------------- Page: 2 ----------------------
oSIST prEN 10370:2019
DRAFT
EUROPEAN STANDARD
prEN 10370
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2019
ICS 77.140.15
English Version
Steel for the reinforcement of concrete - Stainless steel
Aciers pour l'armature du béton - Aciers inoxydables Stahl für die Bewehrung von Beton - Nichtrostender
Stahl
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 4.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10370:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10370:2019
prEN 10370:2019 (E)
Contents Page
European foreword . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, symbols, units and abbreviated terms . 8
4 Product characteristics . 14
4.1 Elongation at maximum load . 14
4.2 Weldability . 14
4.3 Sections and tolerances on sizes (of bars and coils) . 14
4.3.1 Bars and coils . 14
4.3.2 Welded fabric . 16
4.3.3 Lattice girders and hybrid lattice girders . 16
4.4 Bendability (of the bars). 16
4.5 Bond strength (surface geometry) .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.