Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2003)

Beschichtungsstoffe und Kunststoffe - Bestimmung des Gehaltes an nichtflüchtigen Anteilen (ISO 3251:2003)

Diese Internationale Norm legt ein Verfahren zum Bestimmen des Massengehaltes an nichtflüchtigen Anteilen von Beschichtungsstoffen, Bindemitteln für Beschichtungsstoffe, Polymerdispersionen und Kondensationsharzen wie Phenolharze (Resole, Novolak-Lösungen usw.) fest.
Das Verfahren ist auch auf formulierte Polymerdispersionen, die Füllstoffe, Pigmente und sonstige Hilfsstoffe (z. B. Verdickungsmittel, Filmbilde-Hilfsmittel) enthalten, anwendbar. Damit das Verfahren für weichmacherfreie Polymerdispersionen und Kautschuklatices anwendbar ist, muss der nichtflüchtige Rückstand (im Wesentlichen bestehend aus dem Polymermaterial und kleinen Mengen von Hilfsstoffen, wie z. B. Emulgatoren, Schutzkolloiden, Stabilisatoren, Lösemitteln, die als Filmbilde-Hilfsmittel und - insbesondere bei Kautschuklatex-Konzentrat - als Konservierungsmittel zugegeben werden) unter den Prüfbedingungen chemisch stabil sein. Bei weichmacherhaltigen Proben schließt der Rückstand, laut Definition, gewöhnlich den Weichmacher mit ein.
ANMERKUNG 1   Der Gehalt an nichtflüchtigen Anteilen eines Produktes ist keine absolute Größe, sondern hängt von der bei der Prüfung angewendeten Temperatur und der Prüfdauer ab. Bei der Anwendung dieses Verfahrens werden folglich nur relative Werte und nicht die wahren Werte für den Gehalt an nichtflüchtigen Anteilen erhalten, bedingt durch Lösemittelretention, thermische Zersetzung und Verdunstung niedermolekularer Anteile. Das Verfahren ist deshalb in erster Linie für die Prüfung aufeinanderfolgender Lieferungen des gleichen Produktes gedacht.
ANMERKUNG 2   Dieses Verfahren ist geeignet für synthetische Kautschuklatices, wenn die Trocknung während der entsprechenden Zeitspanne als angemessen angesehen wird (ISO 124 schreibt eine Trocknungszeit vor, bei der der Massenverlust einer Probe von 2 g nach aufeinanderfolgenden Trocknungsintervallen weniger als 0,5 mg beträgt).
ANMERKUNG 3   Innerbetriebliche Verfahren zum Bestimmen des Gehaltes an nichtflüchtigen Anteilen sch

Peintures, vernis et plastiques - Détermination de l'extrait sec (ISO 3251:2003)

Barve, laki in plastične mase - Določevanje nehlapnih snovi (ISO 3251:2003)

General Information

Status
Withdrawn
Publication Date
31-Mar-2003
Withdrawal Date
26-Mar-2008
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
25-Mar-2008
Due Date
17-Apr-2008
Completion Date
27-Mar-2008

Relations

Buy Standard

Standard
EN ISO 3251:2003
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3251:2003
01-april-2003
1DGRPHãþD
SIST EN ISO 3251:1997
SIST EN ISO 3251:2008
SIST EN ISO 8618:1999
%DUYHODNLLQSODVWLþQHPDVH'RORþHYDQMHQHKODSQLKVQRYL ,62
Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO
3251:2003)
Beschichtungsstoffe und Kunststoffe - Bestimmung des Gehaltes an nichtflüchtigen
Anteilen (ISO 3251:2003)
Peintures, vernis et plastiques - Détermination de l'extrait sec (ISO 3251:2003)
Ta slovenski standard je istoveten z: EN ISO 3251:2003
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
87.040 Barve in laki Paints and varnishes
SIST EN ISO 3251:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3251:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 3251:2003
EUROPEAN STANDARD
EN ISO 3251
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2003
ICS 87.040; 87.060.20 Supersedes EN ISO 3251:1995 and EN ISO 8618:1998
English version
Paints, varnishes and plastics - Determination of non-volatile-
matter content (ISO 3251:2003)
Peintures, vernis et plastiques - Détermination de l'extrait Beschichtungsstoffe und Kunststoffe - Bestimmung des
sec (ISO 3251:2003) Gehaltes an nichtflüchtigen Anteilen (ISO 3251:2003)
This European Standard was approved by CEN on 13 February 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden, Switzerland and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3251:2003 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3251:2003
EN ISO 3251:2003 (E)
CORRECTED  2003-03-12
Foreword
This document (EN ISO 3251:2003) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 "Paints and
varnishes", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2003, and conflicting national
standards shall be withdrawn at the latest by August 2003.
This document supersedes EN ISO 3251:1995 and EN ISO 8618:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden,
Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 3251:2003 has been approved by CEN as EN ISO 3251:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 3251:2003
EN ISO 3251:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 1513 1992 Paints and varnishes — EN ISO 1513 1994
Examination and preparation of
samples for testing
ISO 2431 1993 Paints and varnishes — EN ISO 2431 1996
Determination of flow time by use
of flow cups
ISO 15528 2000 Paints, varnishes and raw EN ISO 15528 2000
materials for paints and varnishes
— Sampling
3

---------------------- Page: 5 ----------------------

SIST EN ISO 3251:2003

---------------------- Page: 6 ----------------------

SIST EN ISO 3251:2003


INTERNATIONAL ISO
STANDARD 3251
Third edition
2003-02-15


Paints, varnishes and plastics —
Determination of non-volatile-matter
content
Peintures, vernis et plastiques — Détermination de l'extrait sec




Reference number
ISO 3251:2003(E)
©
ISO 2003

---------------------- Page: 7 ----------------------

SIST EN ISO 3251:2003
ISO 3251:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 3251:2003
ISO 3251:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Apparatus. 2
5 Sampling . 3
6 Procedure. 3
7 Supplementary test conditions . 4
8 Expression of results. 5
9 Precision . 6
10 Test report. 6

© ISO 2003 — All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 3251:2003
ISO 3251:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3251 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 10,
Test methods for binders for paints and varnishes, in collaboration with ISO/TC 45, Rubber and rubber
products, as well as ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials, and Subcommittee
SC 12, Thermosetting materials.
This third edition cancels and replaces the second edition (ISO 3251:1993) and, in addition, ISO 1625:1998
and ISO 8618:1995. During the revision and combination of these International Standards, the procedures
used for determining the non-volatile-matter content of polymer dispersions and liquid phenolic resins were
integrated into the procedure used in ISO 3251. The period of heating, temperature and test-portion mass
used for the various types of product were not changed.
iv © ISO 2003 — All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 3251:2003
INTERNATIONAL STANDARD ISO 3251:2003(E)

Paints, varnishes and plastics — Determination of non-volatile-
matter content
1 Scope
This International Standard specifies a method for determining the non-volatile-matter content by mass of
paints, varnishes, binders for paints and varnishes, polymer dispersions and condensation resins such as
phenolic resins (resols, novolak solutions, etc.).
The method is also applicable to formulated dispersions containing fillers, pigments and other auxiliaries (e.g.
thickeners and film-forming agents). For the method to be usable for unplasticized polymer dispersions and
rubber latices, the non-volatile residue (which consists essentially of the polymeric material and of small
quantities of auxiliaries such as emulsifiers, protective colloids, stabilizers, solvents added as film-forming
agents and — especially for rubber latex concentrate — preserving agents) has to be chemically stable under
the test conditions. For plasticized samples, the residue, by definition, normally includes the plasticizer.
NOTE 1 The non-volatile-matter content of a product is not an absolute quantity but depends upon the temperature
and period of heating used for the determination. Consequently, when using this method, only relative and not true values
of the non-volatile-matter content are obtained owing to solvent retention, thermal decomposition and evaporation of low-
molecular-mass constituents. The method is therefore primarily intended for testing different batches of the same type of
product.
NOTE 2 This method is suitable for synthetic rubber latices provided heating for a specific period of time is considered
appropriate (ISO 124 specifies heating until the loss in mass of a 2 g test portion following successive periods of heating is
less than 0,5 mg).
NOTE 3 In-house methods for determining non-volatile matter often include drying with infrared or microwave radiation.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.