ISO 4248:1978
(Main)Jig bushes — Definitions and nomenclature
- BACK
- 31-Jan-1978
- 01.040.25
- 25.060.20
- ISO/TC 29/SC 9
Jig bushes — Definitions and nomenclature
Guides de perçage — Définitions et nomenclature
General Information
This May Also Interest You
ISO 19719:2010 specifies terms and definitions used for clamping technology, including specific technical terms which are commonly used for work holding chucks.
- Standard80 pagesEnglish languagesale 15% off
- 05-Jan-2010
- 01.040.25
- 25.060.20
- ISO/TC 39/SC 8
This document specifies a method for the identification of single fish and fish fillets to the level of genus or species. It allows the identification of a large number of commercially important fish species using DNA barcoding. This method was validated on raw fish. Laboratory experience indicates additional applicability to processed fish products (e.g. cold smoked, hot smoked, salted, frozen, cooked, fried and deep-fried samples). The described method is usually unsuitable for the analysis of highly processed foods (e.g. tins of fish with highly degraded DNA where the fragment lengths are not sufficient for amplification of the targets). Furthermore, it does not apply to complex fish products containing mixtures of two or more fish species. The identification of fish species is carried out by PCR amplification of either a segment of the mitochondrial cytochrome b gene (cytb) or the cytochrome c oxidase I gene (cox1, syn COI), or both, followed by sequencing of the PCR products and subsequent sequence comparison with entries in databases.
- Standard18 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
- 05-Sep-2024
- 67.120.30
- ISO/TC 34/SC 16
This document specifies a method for exposing test specimens to white light emitting diode (LED) lamps at specified temperatures and relative humidity. This document is applicable to coloured and uncoloured plastics that are exposed to white LED lamps in indoor environments such as homes, offices, retail outlets, factory and commercial facilities that do not experience solar radiation through window glass. It can be applicable to plastics in other environments as well.
- Technical specification11 pagesEnglish languagesale 15% off
- 05-Sep-2024
- 83.080.01
- ISO/TC 61/SC 6
- Standard2 pagesEnglish languagesale 15% off
- 05-Sep-2024
- 21.100.20
- ISO/TC 4/SC 5
This document establishes terms, descriptions and characteristics and provides typical photos of specified surface imperfections which can be found on finished silicon nitride rolling elements. Rolling elements refer to balls and rollers. Imperfections defined in this document correspond to patterns found on finished rolling elements before use. Deviations for the geometric product specifications (GPS) are not addressed in this document. This document does not give criteria for the acceptance limits of these imperfections. The identification of an imperfection is done between the different actors involved in the manufacturing, assembly or final use of the silicon nitride parts, depending on the technical specifications and the criticality of the application.
- Standard33 pagesEnglish languagesale 15% off
- Standard35 pagesFrench languagesale 15% off
This document specifies the general procedure to be followed in determining the dynamic viscosity of unpigmented coating materials, such as paints, varnishes and related products, as well as binders at a shear rate range between 9 000 s−1 and 12 000 s−1. It describes an absolute viscosity measurement with cone-plate measuring geometry at high shear rates. The measured value gives information about the resistance offered by the material to brushing, spraying and roller coating during application. The method specified in this document is suitable for all paints and varnishes whether they are Newtonian in behaviour or not. For materials containing dispersions of large particles, the measuring geometry is expected to be adapted.
- Standard5 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
- 05-Sep-2024
- 87.040
- ISO/TC 35/SC 9
This document specifies water jet cleaning methods for the removal of the existing coatings and rust during surface preparation of steel surfaces before application of paints and related products. It provides information on the effectiveness of the individual methods and their fields of application. It also describes the equipment and the procedures to follow.
- Standard15 pagesEnglish languagesale 15% off
- 05-Sep-2024
- 25.220.10
- ISO/TC 35/SC 12
This document gives guidance on the characteristics and best practices of a professional farmer organization. This document is applicable to commercially oriented farmer organizations. It does not apply to purely socially oriented farmer organizations or individual farmers. It provides a common standard of professionalism for commercially oriented farmer organizations, which can serve as guidance to inform, harmonize, and complement existing and future organizational development and assessment processes. This document is applicable to large and small farmer organizations, without regard to the number of members, volume of business, output or capital investment, nor to the specific crop or product. It can also be applicable, when adapted, for very small or nascent organizations, for specific or differentiated products or for markets with special requirements. It does not address every capacity or aspect of professionalism that can be of importance to a specific customer or market, nor imply the need for uniformity in organizational type or structure.
- Standard12 pagesEnglish languagesale 15% off
This document specifies requirements for non-sterile, single-use graduated flow regulators used as subcomponents in sterilized infusion sets for single use to control the flow of intravenous infusion solutions with fluid contact under gravity feed conditions.
- Standard6 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies an automatic method for the reference method (see ISO 712-1) for the determination of moisture content of cereals and cereal products using an automatic drying oven. This document is applicable to wheat, rice (paddy, husked and milled), barley, millet (Panicum miliaceum), rye, oats, triticale, sorghum in the form of grains, milled grains, semolina and flour. The method does not apply to maize and pulses. NOTE For moisture content determination in maize, see ISO 6540, and for pulses, see ISO 24557.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
- 05-Sep-2024
- 67.060
- ISO/TC 34/SC 4
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.