ISO 8124-4:2014/Amd 2:2019

INTERNATIONAL ISO
STANDARD 8124-4
Second edition
2014-10-01
AMENDMENT 2
2019-03
Safety of toys —
Part 4:
Swings, slides and similar activity
toys for indoor and outdoor family
domestic use
AMENDMENT 2
Sécurité des jouets —
Partie 4: Balançoires, glissoires et jouets à activité similaire à usage
domestique familial intérieur et extérieur
AMENDEMENT 2
Reference number
ISO 8124-4:2014/Amd.2:2019(E)
©
ISO 2019
ISO 8124-4:2014/Amd.2:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 8124-4:2014/Amd.2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 181, Safety of toys.
The main changes are as follows:
— Requirements for minimum clearance and lateral stability have been adjusted to provide for swing
elements with a single point of suspension.
— The minimum clearance between footrests on swing elements and the ground has been adjusted to
align with ASTM F1148.
A list of all parts in the ISO 8124 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 8124-4:2014/Amd.2:2019(E)
Safety of toys —
Part 4:
Swings, slides and similar activity toys for indoor and
outdoor family domestic use
AMENDMENT 2
Figure 4
Replace as follows.
a)   Example of a flat seat b)  Example of a gondola
Key
1 crossbeam/support member
2 suspension connector
3 suspension coupling
4 means of suspension
5 swing device
6 swing element (e.g. seat, rings, bar, gondola)
NOTE A swing device can include one or more footrests. Footrests are considered as parts of the swing
elements
Figure 4 — Diagrammatic representation of examples of
...