ISO 16145-1:2012
(Main)Ships and marine technology — Protective coatings and inspection method — Part 1: Dedicated sea water ballast tanks
Ships and marine technology — Protective coatings and inspection method — Part 1: Dedicated sea water ballast tanks
This part of ISO 16145 specifies a method of protective coatings and its inspection for dedicated seawater ballast tanks. It is applicable to all types of ships of not less than 500 gross tonnage and double-side skin spaces of bulk carriers of 150 m in length and upwards, which are contracted for new building on or after 1 July 2008; or in the absence of a building contract, the keels of which are laid or which are at a similar stage of construction on or after 1 January 2009; or the delivery of which is on or after 1 July 2012. This part of ISO 16145 also is applicable to the dedicated seawater ballast tanks of oil tankers of double hull construction of 150 m in length and upwards and double-side skin spaces of bulk carriers of 90 m in length and upwards, which are contracted for new building on or after 8 December 2006. NOTE Double-side skin space is a configuration where each ship side is constructed by the side shell with a longitudinal bulkhead connecting to the double bottom and the deck. Hopper side tanks and top-side tanks may, where fitted, be integral parts of the double-side skin configuration. Therefore, the void spaces or other designated tanks arranged as a part of top-side tank, when provided in the bulk carriers of single-side skin construction, need not be considered as a double-side skin space
Navires et technologie maritime — Revêtements de protection et méthode d'inspection — Partie 1: Ballasts d'eau de mer dédiée
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 16145-1
First edition
2012-10-01
Ships and marine technology — Protective
coatings and inspection method —
Part 1:
Dedicated sea water ballast tanks
Navires et technologie maritime — Revêtements de protection et
méthode d’inspection —
Partie 1: Ballasts d’eau de mer dédiée
Reference number
ISO 16145-1:2012(E)
©
ISO 2012
---------------------- Page: 1 ----------------------
ISO 16145-1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 16145-1:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 Symbols and abbreviated terms . 4
4.1 Symbols . 4
4.2 Abbreviated terms . 4
5 General procedures for coating work . 4
6 Standard for coating work . 6
6.1 Surface preparation . 6
6.2 Primary surface preparation and shop priming . 7
6.3 Secondary surface preparation . 9
6.4 Coating .10
6.5 Treatment for coating defects .13
7 Inspection .14
7.1 Inspection procedure .14
7.2 Coating inspection .14
7.3 Dry film thickness measurement .16
Annex A (informative) Measurement of the conductivity for abrasives .21
Annex B (informative) Measurement of water soluble salt.23
Annex C (informative) Inspection items and management of inspection .25
Annex D (informative) Assessment for the degree of damage .30
Annex E (informative) Standard for coating technical file (CTF) .31
Bibliography .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.