ISO 363-2:2006
(Main)Textile machinery and accessories - Flat steel healds with closed end loops - Part 2: Dimensions of healds manufactured of hardened strip steel
Textile machinery and accessories - Flat steel healds with closed end loops - Part 2: Dimensions of healds manufactured of hardened strip steel
ISO 363-2:2006 specifies the main dimensions and tolerances of flat steel healds with closed end loops (O-shaped end loops) manufactured of hardened strip steel for use in the textile industry.
Matériel pour l'industrie textile — Lisses en acier plat avec boucles d'extrémités fermées — Partie 2: Dimensions des lisses fabriquées en feuillards d'acier trempé
L'ISO 363-2:2006 spécifie les dimensions principales et les tolérances des lisses en acier plat avec boucles d'extrémités fermées (boucles d'extrémité de forme-O) fabriquées en feuillards d'acier trempé destinées à être utilisées dans l'industrie textile.
General Information
- Status
- Published
- Publication Date
- 14-Mar-2006
- Current Stage
- 9599 - Withdrawal of International Standard
- Start Date
- 18-Nov-2024
- Completion Date
- 13-Dec-2025
Overview
ISO 363-2:2006 specifies the main dimensions and tolerances for flat steel healds with closed end loops (O‑shaped end loops) manufactured from hardened strip steel for the textile industry. This part of ISO 363 covers the dimensional series and allowable variations (in millimetres), including standard cross‑sections and loop‑to‑loop distances, and presents the information graphically (figure) and in tabular form for simplex (single eyelet row) and duplex (double eyelet row) healds.
Key Topics
- Scope and dimensional requirements: Defines the principal dimensions and tolerances of flat steel healds made of hardened strip steel for use on weaving machines.
- Heald types: Distinguishes simplex (single eyelet) and duplex (double eyelet) configurations and provides separate dimensional tables for each.
- Cross‑section and material: Typical cross‑section examples appear in the tables (e.g., 5.5 × 0.3 mm) and the standard is specific to healds manufactured from hardened strip steel.
- Loop geometry: Specifies the O‑shaped closed end loops (closed end loops) geometry and the distances between end loops (examples of standard lengths include 260, 280, 302, 330 mm).
- Tolerance and interchangeability: Establishes tolerances to ensure compatibility between healds and textile machinery, facilitating interchangeability and consistent performance.
Applications
ISO 363-2:2006 is used where precise, repeatable heald dimensions are critical:
- Specification and procurement of flat steel healds for shuttle and modern weaving machines.
- Manufacturing and quality control for heald producers using hardened strip steel.
- Design and maintenance of textile machinery where component interchangeability and adherence to dimensional tolerance are required.
- Inventory standardization for textile mills, service workshops, and spare‑parts suppliers to reduce machine downtime and ensure reliable weaving performance.
Who Should Use This Standard
- Heald and textile component manufacturers
- Weaving machine OEMs and design engineers
- Purchasing and procurement teams in textile mills
- Quality control and inspection personnel
- Maintenance technicians and spare‑parts managers
Related Standards
- ISO 363-1 - Part 1: Dimensions of healds manufactured of rolled steel wire (companion document for wire healds)
- Other ISO and industry standards addressing textile machinery dimensions and component interchangeability
ISO 363-2:2006 provides a concise, practical reference for heald dimensions, tolerances, and O‑shaped end loop specifications, helping manufacturers and textile professionals ensure compatibility, quality, and reliable loom operation.
ISO 363-2:2006 - Textile machinery and accessories -- Flat steel healds with closed end loops
ISO 363-2:2006 - Matériel pour l'industrie textile -- Lisses en acier plat avec boucles d'extrémités fermées
Frequently Asked Questions
ISO 363-2:2006 is a standard published by the International Organization for Standardization (ISO). Its full title is "Textile machinery and accessories - Flat steel healds with closed end loops - Part 2: Dimensions of healds manufactured of hardened strip steel". This standard covers: ISO 363-2:2006 specifies the main dimensions and tolerances of flat steel healds with closed end loops (O-shaped end loops) manufactured of hardened strip steel for use in the textile industry.
ISO 363-2:2006 specifies the main dimensions and tolerances of flat steel healds with closed end loops (O-shaped end loops) manufactured of hardened strip steel for use in the textile industry.
ISO 363-2:2006 is classified under the following ICS (International Classification for Standards) categories: 59.120.30 - Looms. Weaving machines. The ICS classification helps identify the subject area and facilitates finding related standards.
You can purchase ISO 363-2:2006 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 363-2
First edition
2006-03-15
Textile machinery and accessories — Flat
steel healds with closed end loops —
Part 2:
Dimensions of healds manufactured of
hardened strip steel
Matériel pour l'industrie textile — Lisses en acier plat avec boucles
d'extrémités fermées —
Partie 2: Dimensions des lisses fabriquées en feuillard d'acier trempé
Reference number
©
ISO 2006
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (I
...
NORME ISO
INTERNATIONALE 363-2
Première édition
2006-03-15
Matériel pour l'industrie textile — Lisses
en acier plat avec boucles d'extrémités
fermées —
Partie 2:
Dimensions des lisses fabriquées en
feuillards d'acier trempé
Textile machinery and accessories — Flat steel healds with closed end
loops —
Part 2: Dimensions of healds manufactured of hardened strip steel
Numéro de référence
©
ISO 2006
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2006
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2006 – Tous droits réservés
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechn
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...