Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts - Amendment 1

Méthodes pour l'étalonnage des transducteurs de vibrations et de chocs — Partie 1: Concepts de base — Amendement 1

General Information

Status
Published
Publication Date
13-Jul-2016
ICS
17.160 - Vibrations, shock and vibration measurements
Technical Committee
ISO/TC 108 - Mechanical vibration, shock and condition monitoring
Drafting Committee
ISO/TC 108/WG 34 - Calibration of vibration and shock transducers
Current Stage
6060 - International Standard published
Start Date
14-Jul-2016
Due Date
13-Mar-2019
Completion Date
13-Mar-2019

Relations

Amends
ISO 16063-1:1998 - Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts
Effective Date
11-Dec-2021

Overview

ISO 16063-1:1998/Amd 1:2016 is an international standard published by the International Organization for Standardization (ISO). It specifies basic concepts for the calibration of vibration and shock transducers-sensors used to measure vibration and shock in various mechanical systems. This amendment provides important updates enhancing the fundamental framework for calibration methods, ensuring accuracy and reliability in dynamic measurements.

This standard is a critical reference for professionals working with vibration measurement equipment, including engineers, calibration laboratories, and quality assurance teams. It contributes to maintaining uniformity and conformity in vibration transducer calibration worldwide.

Key Topics

Calibration Basics for Vibration & Shock Transducers

  • Establishes terms and definitions essential for understanding transducer calibration.
  • Focuses on basic principles guiding calibration procedures and measurement accuracy.
  • Addresses motion measurement in vibration generators, including acceleration, velocity, and displacement.

Introduction of Transverse Motion Ratio

  • Defines transverse motion ratio as the maximum ratio of motion perpendicular to the operating axis relative to the motion along the axis.
  • Provides formulas to calculate transverse motion amplitude and ratio using accelerations in orthogonal directions.
  • Explains measurement techniques utilizing tri-axis transducers or orthogonal blocks.
  • Highlights the use of laser interferometry and signal processing methods such as bandpass and tracking filters to analyze transverse motion.

Measurement and Analysis

  • Emphasizes simultaneous measurement of orthogonal motion components for comprehensive calibration.
  • Addresses signal processing impacts on transverse motion analysis, ensuring harmonics are accurately accounted for.
  • Introduces guidelines for reproducible and precise transverse motion assessment in calibration.

Applications

ISO 16063-1:1998/Amd 1:2016 is widely applicable across industries relying on precise vibration and shock monitoring:

  • Industrial Equipment Maintenance: Ensures accurate vibration measurement for machinery condition monitoring and predictive maintenance.
  • Automotive Testing: Calibrates sensors used in vehicle vibration and shock tests to verify component durability and safety.
  • Aerospace Engineering: Supports calibration of transducers deployed in flight testing and structural health monitoring.
  • Research & Development: Provides foundational calibration concepts for developing new sensor technologies and measurement methods.
  • Calibration Laboratories: Standardizes procedures and terminologies for accredited calibration services on force, vibration, and shock transducers.

The amendment enhances measurement precision and standard conformity, crucial for maintaining quality control and safety in systems subjected to dynamic forces.

Related Standards

ISO 16063-1:1998/Amd 1:2016 complements other parts of the ISO 16063 series that provide detailed calibration methods for specific types of transducers and testing scenarios:

  • ISO 16063-2: Calibration methods using comparison vibration calibration.
  • ISO 16063-3: Primary calibration by laser interferometry.
  • ISO 16063-4: Calibration of seismic accelerometers.
  • ISO 16063-5: Calibration using electro-dynamic shakers.

These standards together provide a comprehensive framework supporting reliable calibration practices for vibration and shock measurement instruments.

Keywords: ISO 16063-1, vibration transducer calibration, shock transducer calibration, transverse motion ratio, vibration measurement standards, dynamic sensor calibration, mechanical vibration monitoring, laser interferometry calibration, ISO mechanical vibration standards.

Frequently Asked Questions

ISO 16063-1:1998/Amd 1:2016 is a standard published by the International Organization for Standardization (ISO). Its full title is "Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts - Amendment 1". This standard covers: Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts - Amendment 1

Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts - Amendment 1

ISO 16063-1:1998/Amd 1:2016 is classified under the following ICS (International Classification for Standards) categories: 17.160 - Vibrations, shock and vibration measurements. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO 16063-1:1998/Amd 1:2016 has the following relationships with other standards: It is inter standard links to ISO 16063-1:1998. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ISO 16063-1:1998/Amd 1:2016 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


DRAFT AMENDMENT
ISO 16063-1:1998/DAM 1
ISO/TC 108/SC 3 Secretariat: DS
Voting begins on: Voting terminates on:
2015-07-06 2015-10-06
Methods for the calibration of vibration and shock
transducers —
Part 1:
Basic concepts
AMENDMENT 1
Méthodes pour l’étalonnage des transducteurs de vibrations et de chocs —
Partie 1: Concepts de base
AMENDEMENT 1
ICS: 17.160
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 16063-1:1998/DAM 1:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

ISO 16063-1:1998/DAM 1:2015(E)

© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 16063‐1:1998 DAmd. 1
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non‐governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and
...


INTERNATIONAL ISO
STANDARD 16063-1
First edition
1998-10-15
AMENDMENT 1
2016-07-15
Methods for the calibration of
vibration and shock transducers —
Part 1:
Basic concepts
AMENDMENT 1
Méthodes pour l’étalonnage des transducteurs de vibrations et de
chocs —
Partie 1: Concepts de base
AMENDEMENT 1
Reference number
ISO 16063-1:1998/Amd.1:2016(E)
©
ISO 2016
ISO 16063-1:1998/Amd.1:2016(E)

© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 16063-1:1998/Amd.1:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the follow
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...