IEC TS 60839-7-8:2019
(Main)Alarm systems - Part 7-8: Message formats and protocols for serial data interfaces in alarm transmission systems - Requirements for common protocol for alarm transmission using the Internet protocol
Alarm systems - Part 7-8: Message formats and protocols for serial data interfaces in alarm transmission systems - Requirements for common protocol for alarm transmission using the Internet protocol
IEC 60839-7-8:2019 specifies a protocol for point-to-point transmission of alarms and faults, as well as communications monitoring, between a supervised premises transceiver and a receiving centre transceiver using the Internet protocol (IP).
The protocol is intended for use over any network that supports the transmission of IP data. These include Ethernet, xDSL, GPRS, WiFi, UMTS and WIMAX.
The system performance characteristics for alarm transmission are specified in IEC 60839‑5‑1.
The performance characteristics of the supervised premises equipment comply with the requirements of its associated alarm system standard and apply for transmission of all types of alarms including, but not limited to, fire, intrusion, access control and social alarms.
General Information
Buy Standard
Standards Content (Sample)
IEC TS 60839-7-8 ®
Edition 1.0 2019-05
TECHNICAL
SPECIFICATION
Alarm systems –
Part 7-8: Message formats and protocols for serial data interfaces in alarm
transmission systems – Requirements for common protocol for alarm
transmission using the Internet protocol
All rights reserved. Unless otherw ise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, w ithout permission in w riting from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 w ww.iec.ch
Sw itzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, w ith equivalent terms in 16 additional languages.
and w ithdraw n publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 60839-7-8 ®
Edition 1.0 2019-05
TECHNICAL
SPECIFICATION
Alarm systems –
Part 7-8: Message formats and protocols for serial data interfaces in alarm
transmission systems – Requirements for common protocol for alarm
transmission using the Internet protocol
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 13.320 ISBN 978-2-8322-6813-1
– 2 – IEC TS 60839-7-8:2019 © IEC 2019
CONTENTS
FOREWORD . 6
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviations . 8
3.1 Terms and definitions . 8
3.2 Abbreviations . 9
4 Objective . 9
5 Messaging . 10
5.1 General . 10
5.2 Message format overview . 10
5.2.1 General . 10
5.2.2 Identifiers . 10
5.2.3 Message format . 11
5.2.4 Connection handle. 12
5.2.5 Device ID . 12
5.2.6 Message ID . 13
5.2.7 Message length . 14
5.2.8 Sequence numbers . 14
5.2.9 Flags. 14
5.3 Padding and message length . 14
5.3.1 Padding . 14
5.3.2 Message length . 15
5.4 Hashing . 15
5.5 Encryption . 15
5.5.1 General . 15
5.5.2 Key exchange . 16
5.6 Timeouts and retries . 16
5.7 Version number . 17
5.8 Reverse commands . 17
5.9 Initial values . 18
6 Message types . 18
6.1 General . 18
6.2 Path supervision . 18
6.2.1 General . 18
6.2.2 Poll message . 18
6.2.3 Poll response . 19
6.3 Event reporting . 19
6.3.1 Event message format . 19
6.3.2 Event response format. 22
6.4 Configuration messages . 23
6.4.1 General . 23
6.4.2 Connection handle request . 23
6.4.3 Connection handle response . 24
6.4.4 Device ID request. 24
6.4.5 Device ID response . 25
6.4.6 Encryption selection request . 25
6.4.7 Encryption selection response . 26
6.4.8 Encryption key exchange request . 26
6.4.9 Encryption key exchange response. 27
6.4.10 Hash selection request . 27
6.4.11 Hash selection response . 28
6.4.12 Path supervision request. 28
6.4.13 Path supervision response . 29
6.4.14 Set time command. 29
6.4.15 Set time response . 29
6.4.16 Protocol version request . 30
6.4.17 Protocol version response . 30
6.4.18 Transparent message. 30
6.4.19 Transparent response . 30
6.4.20 DTLS completed request . 31
6.4.21 DTLS completed response. 31
6.4.22 RCT IP parameter request . 31
6.4.23 RCT IP parameter response. 32
7 Commissioning and connection setup . 32
7.1 Commissioning . 32
7.1.1 General . 32
7.1.2 Procedures . 33
7.1.3 Commissioning message sequence . 33
7.1.4 Commissioning using shared secret . 34
7.1.5 Commissioning using X.509 certificates and DTLS . 35
7.2 Connection setup . 36
Annex A (normative) Result codes . 38
Annex B (normative) Protocol identifiers. 39
Annex C (normative) Shared secret. 40
C.1 Formatting of the shared secret . 40
C.2 Checksum for shared secret formatting. 40
C.3 Example of secret encoding and formatting. 40
Annex D (informative) Examples of messaging sequences . 42
D.1 Commissioning . 42
D.2 Connection setup . 45
Annex E (informative) Examples of application protocols . 48
E.1 SIA . 48
E.2 Ademco contact ID . 48
E.3 Scancom fast format . 49
E.4 VdS 2465 . 49
Annex F (informative) Design principles . 51
F.1 General . 51
F.2 Information security . 51
F.3 Use of UDP signalling . 51
Bibliography . 52
Table 1 – Identifiers . 10
Table 2 – Basic unencrypted format of messages . 11
– 4 – IEC TS 60839-7-8:2019 © IEC 2019
Table 3 – Basic encrypted format of messages . 11
Table 4 – Message ID overview . 13
Table 5 – Flags . 14
Table 6 – Hashing IDs . 15
Table 7 – Encryption IDs . 16
Table 8 – Reverse commands . 17
Table 9 – Initial values. 18
Table 10 – Poll message SPT RCT . 18
Table 11 – Poll response RCT SPT. 19
Table 12 – Event message format – SPT RCT . 20
Table 13 – Event message format – Fields . 20
Table 14 – Event field. 21
Table 15 – Time event field . 21
Table 16 – Time message f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.