IEC 61338-1:2004
(Main)Waveguide type dielectric resonators - Part 1: Generic specification
Waveguide type dielectric resonators - Part 1: Generic specification
IEC 61338-1:2004 applies to waveguide type dielectric resonators of assessed quality using either capability approval or qualification approval procedures. It also lists the test and measurement procedures which may be selected for use in detail specifications for such resonators.
Résonateurs diélectriques à modes guidés - Partie 1: Spécification générique
La CEI 61338-1:2004 s'applique aux résonateurs diélectriques à modes guidés sous assurance de la qualité en utilisant soit des procédures d'agrément de savoir-faire, soit des procédures d'homologation. Elle donne également les procédures d'essai et de mesure qui peuvent être sélectionnées pour être utilisées dans des spécifications particulières pour de tels résonateurs.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL IEC
STANDARD 61338-1
First edition
2004-11
Waveguide type dielectric resonators –
Part 1:
Generic specification
Reference number
Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the
60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.
Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example,
edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the
base publication incorporating amendment 1 and the base publication incorporating
amendments 1 and 2.
Further information on IEC publications
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology. Information relating to
this publication, including its validity, is available in the IEC Catalogue of
publications (see below) in addition to new editions, amendments and corrigenda.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is also available from the following:
• IEC Web Site (www.iec.ch)
• Catalogue of IEC publications
The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to
search by a variety of criteria including text searches, technical committees
and date of publication. On-line information is also available on recently issued
publications, withdrawn and replaced publications, as well as corrigenda.
• IEC Just Published
This summary of recently issued publications (www.iec.ch/online_news/ justpub)
is also available by email. Please contact the Customer Service Centre (see
below) for further information.
• Customer Service Centre
If you have any questions regarding this publication or need further assistance,
please contact the Customer Service Centre:
Email: custserv@iec.ch
Tel: +41 22 919 02 11
Fax: +41 22 919 03 00
INTERNATIONAL IEC
STANDARD 61338-1
First edition
2004-11
Waveguide type dielectric resonators –
Part 1:
Generic specification
IEC 2004 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale V
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
– 2 – 61338-1 IEC:2004(E)
CONTENTS
FOREWORD.4
1 General.6
1.1 Scope.6
1.2 Normative references.6
1.3 Order of precedence.7
2 Terminology and general requirements .7
2.1 General.7
2.2 Definitions.8
2.3 Preferred values for ratings and characteristics.18
2.4 Marking.19
3 Quality assessment procedures .19
3.1 General.19
3.2 Primary stage of manufacture .19
3.3 Structurally similar components .19
3.4 Sub-contracting.19
3.5 Manufacturer’s approval.20
3.6 Approval procedures.20
3.7 Procedures for capability approval .21
3.8 Procedures for qualification approval .21
3.9 Test procedures.21
3.10 Screening requirements.22
3.11 Rework and repair work .22
3.12 Certified records of released lots .22
3.13 Validity of release .22
3.14 Release for delivery.22
3.15 Unchecked parameters.22
4 Test and measurement procedures .23
4.1 General.23
4.2 Test and measurement conditions.23
4.3 Visual inspection.23
4.4 Dimension and gauging procedure .23
4.5 Electrical test procedures .24
4.6 Mechanical and environmental test procedures. .30
Figure 1 – TE mode dielectric resonator.10
01δ
Figure 2 – TM mode dielectric resonator.10
Figure 3 – TM mode dielectric resonator .11
01δ
Figure 4 – Hybrid mode dielectric resonator.12
Figure 5 – Multimode dielectric resonators.13
Figure 6 – TEM mode coaxial dielectric resonator.14
Figure 7 – Half wavelength stripline resonator .15
Figure 8 – Half wavelength microstripline resonator .16
61338-1 IEC:2004(E) – 3 –
Figure 9 – Coplanar resonator .17
Figure 10 – Transmission measurement .24
Figure 11 – Resonator test fixture .27
Figure 12 – Frequency response for test fixture A, B and D .28
Figure 13 – Frequency response for test fixture C.28
– 4 – 61338-1 IEC:2004(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
WAVEGUIDE TYPE DIELECTRIC RESONATORS –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This International Standard IEC 61338-1 has been prepared by IEC technical committee 49:
Piezoelectric and dielectric devices for frequency control and selection.
IEC 61338-1 cancels and replaces the first edition of IEC 61338-1-1 published in 1996 and the
first edition of IEC 61338-1-2 published in 1998.
The text of this standard is based on the following documents:
FDIS Report on voting
49/690/FDIS 49/ 699/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
61338-1 IEC:2004(E) – 5 –
IEC 61338 consists of the following parts, under the general title Waveguide type dielectric
resonators:
Part 1: Generic specification
Part 1-3: General information and test conditions – Measurement method of complex relative
permittivity for dielectric resonator materials at microwave frequency
Part 2: Guidelines for oscillator and filter applications
Part 4: Sectional specification
Part 4-1: Blank detail specification
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
– 6 – 61338-1 IEC:2004(E)
WAVEGUIDE TYPE DIELECTRIC RESONATORS –
Part 1: Generic specification
1 General
1.1 Scope
This part of IEC 61338 applies to waveguide type dielectric resonators of assessed quality
using either capability approval or qualification approval procedures. It also lists the test and
measurement procedures which may be selected for use in detail specifications for such
resonators.
1.2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60027 (all parts), Letter symbols to be used in electrical technology
IEC 60050(561):1991, International Electrotechnical Vocabulary (IEV) – Chapter 561: Piezo-
electric devices for frequency control and selection
IEC 60068-1:1988, Environmental testing – Part 1: General and guidance
IEC 60068-2-1:1990, Environmental testing – Part 2: Tests – Tests A: Cold
IEC 60068-2-2:1974, Environmental testing – Part 2: Tests – Tests B: Dry Heat
IEC 60068-2-6:1995, Environmental testing – Part 2: Tests – Tests Fc: Vibration (sinusoidal)
IEC 60068-2-7:1983, Environmen
...
IEC 61338-1 ®
Edition 1.0 2004-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Waveguide type dielectric resonators –
Part 1: Generic specification
Résonateurs diélectriques à modes guidés –
Partie 1: Spécification générique
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.
IEC 61338-1 ®
Edition 1.0 2004-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Waveguide type dielectric resonators –
Part 1: Generic specification
Résonateurs diélectriques à modes guidés –
Partie 1: Spécification générique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX V
ICS 31.140 ISBN 978-2-8322-1000-0
– 2 – 61338-1Ó IEC:2004
CONTENTS
FOREW ORD . 4
1 General . 6
1.1 Scope . 6
1.2 Normative references . 6
1.3 Order of precedence . 7
2 Terminology and general requirements . 7
2.1 General . 7
2.2 Definitions . 8
2.3 Preferred values for ratings and characteristics . 18
2.4 Marking . 19
3 Quality assessment procedures . 19
3.1 General . 19
3.2 Primary stage of manufacture . 19
3.3 Structurally similar components . 19
3.4 Sub-contracting . 19
3.5 Manufacturer’s approval . 20
3.6 Approval procedures . 20
3.7 Procedures for capability approval . 21
3.8 Procedures for qualification approval . 21
3.9 Test procedures. 22
3.10 Screening requirements . 22
3.11 Rework and repair work . 22
3.12 Certified records of released lots . 22
3.13 Validity of release . 22
3.14 Release for delivery . 22
3.15 Unchecked parameters . 22
4 Test and measurement procedures . 23
4.1 General . 23
4.2 Test and measurement conditions . 23
4.3 Visual inspection . 23
4.4 Dimension and gauging procedure . 23
4.5 Electrical test procedures . 24
4.6 Mechanical and environmental test procedures. . 30
Figure 1 – TE mode dielectric resonator . 10
01d
Figure 2 – TM mode dielectric resonator . 11
Figure 3 – TM mode dielectric resonator. 11
01d
Figure 4 – Hybrid mode dielectric resonator . 12
Figure 5 – Multimode dielectric resonators . 13
Figure 6 – TEM mode coaxial dielectric resonator . 14
Figure 7 – Half wavelength stripline resonator. 15
Figure 8 – Half wavelength microstripline resonator . 16
Figure 9 – Coplanar resonator. 17
61338-1Ó IEC:2004 – 3 –
Figure 10 – Transmission measurement . 25
Figure 11 – Resonator test fixture . 27
Figure 12 – Frequency response for test fixture A, B and D. 28
Figure 13 – Frequency response for test fixture C . 28
– 4 – 61338-1Ó IEC:2004
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
WAVEGUIDE TYPE DIELECTRIC RESONATORS –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This International Standard IEC 61338-1 has been prepared by IEC technical committee 49:
Piezoelectric and dielectric devices for frequency control and selection.
IEC 61338-1 cancels and replaces the first edition of IEC 61338-1-1 published in 1996 and
the first edition of IEC 61338-1-2 published in 1998.
This bilingual version (2013-08) corresponds to the monolingual English version, published
in 2004-11.
The text of this standard is based on the following documents:
DIS Report on Voting
49/690/FDIS 49/699/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
61338-1Ó IEC:2004 – 5 –
The French version of this standard
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.