IEC 60404-8-10:2009
(Main)Magnetic materials - Part 8-10: Specifications for individual materials - Magnetic materials (iron and steel) for use in relays
Magnetic materials - Part 8-10: Specifications for individual materials - Magnetic materials (iron and steel) for use in relays
IEC 60404-8-10:2009 specifies the general requirements, magnetic properties, geometric characteristics and tolerances as well as inspection procedures for magnetic materials used primarily for relays. This standard applies to pure iron, non-alloyed and alloyed steel and ferritic stainless steel products usually delivered in either the semi-processed or fully-processed state. These materials correspond to classes A, B, C and D.3 of IEC 60404-1. This second edition cancels and replaces the first edition published in 1994 and constitutes a technical revision. The main modifications from the previous edition of the standard are as follows:
- introduction of the ferritic stainless steels and the fully-processed state in the scope of the standard (see Clause 1);
- modification of the designation with the letter R at the beginning and the condition and state at the end (see Clause 5);
- introduction of the new grades R160 and R320 (see Table 2);
- modification of the requirements for the heat treatment of test specimens for semi-processed material (see Subclause 8.3.1);
- indication in Bibliography of standards referred to in this standard as an information.
Matériaux magnétiques - Partie 8-10: Spécifications pour matériaux particuliers - Matériaux magnétiques (fer et acier) pour relais
La CEI 60404-8-10:2009 spécifie les exigences générales, les caractéristiques magnétiques, les caractéristiques géométriques et tolérances ainsi que les conditions de contrôle des matériaux magnétiques employés principalement pour les relais. La présente norme est applicable aux produits en fer pur, en acier non allié et acier allié et en acier inoxydable ferritique habituellement livrés à l'état semi-fini ou à l'état fini. Ces matériaux correspondent aux classes A, B, C et D.3 de la CEI 60404-1. Cette deuxième édition annule et remplace la première édition parue en 1994, dont elle constitue une révision technique. Les modifications principales de la norme par rapport à l'édition précédente sont les suivantes:
- introduction des aciers inoxydables ferritiques et l'état fini dans le domaine d'application de la norme (voir Article 1);
- modification de la désignation avec la lettre R au début et l'état de livraison et l'état à la fin (voir Article 5);
- introduction de nouvelles nuances R160 et R320 (voir Tableau 2);
- modification des exigences pour le traitement thermique des éprouvettes pour les produits à l'état semi-fini (voir Paragraphe 8.3.1);
- indication dans la bibliographie des normes référencées dans la présente norme à titre d'information.
General Information
Standards Content (Sample)
IEC 60404-8-10 ®
Edition 2.0 2009-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Magnetic materials –
Part 8-10: Specifications for individual materials – Magnetic materials (iron and
steel) for use in relays
Matériaux magnétiques –
Partie 8-10: Spécifications pour matériaux particuliers – Matériaux magnétiques
(fer et acier) pour relais
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60404-8-10 ®
Edition 2.0 2009-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Magnetic materials –
Part 8-10: Specifications for individual materials – Magnetic materials (iron and
steel) for use in relays
Matériaux magnétiques –
Partie 8-10: Spécifications pour matériaux particuliers – Matériaux magnétiques
(fer et acier) pour relais
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
S
CODE PRIX
ICS 29.030 ISBN 978-2-88910-189-4
– 2 – 60404-8-10 © IEC:2009
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 Terms and definitions .6
4 Classification.7
5 Designation .7
6 General requirements .8
6.1 Production process.8
6.2 Form of supply .8
6.2.1 Strip .8
6.2.2 Sheet and plate .8
6.2.3 Flats and bars .9
6.2.4 Wire rod and wire .9
6.3 Delivery condition and state .9
6.4 Surface condition .9
7 Technical requirements .9
7.1 Magnetic properties.9
7.2 Geometric characteristics and tolerances .10
7.2.1 Thickness of flat products.10
7.2.2 Diameter or side dimension of long products .12
7.2.3 Width of flat products.13
7.2.4 Flatness (wave factor) of flat products .14
7.2.5 Length .15
7.2.6 Edge camber for flat products.16
7.2.7 Straightness of hot-rolled flats and bars.16
8 Inspection.17
8.1 General .17
8.2 Selection of samples .17
8.2.1 General .17
8.2.2 Flat products .17
8.2.3 Long products.18
8.2.4 Wire rod and wire .18
8.3 Preparation of test specimens .18
8.3.1 Coercivity .18
8.3.2 Geometrical characteristics and tolerances.18
8.4 Test methods .18
8.4.1 General .18
8.4.2 Coercivity .19
8.4.3 Thickness of flat products.19
8.4.4 Width of flat products.19
8.4.5 Flatness (wave factor) of flat products .19
8.4.6 Edge camber of flat products .19
8.4.7 Dimensions of long products.19
8.4.8 Straightness of long products .19
8.4.9 Retest .19
9 Complaints .19
60404-8-10 © IEC:2009 – 3 –
10 Ordering information.19
Bibliography.21
Table 1 – Types of delivery condition and state .9
Table 2 – Coercivity and availability of grades .10
Table 3 – Tolerances on thickness for hot-rolled strip and sheet .10
Table 4 – Tolerances on thickness for hot-rolled plates.11
Table 5 – Tolerances on thickness for cold-rolled flat products .11
Table 6 – Tolerances on thickness for hot-rolled flats .11
Table 7 – Tolerances on diameter for hot-rolled rounds .12
Table 8 – Tolerances on side dimension for hot-rolled squares .12
Table 9 – Tolerances on the dimension of wire rod .12
Table 10 – Tolerances on the diameter of wire.13
Table 11 – Tolerances on width for hot-rolled strip and sheet .13
Table 12 – Tolerances on width for hot-rolled plate.13
Table 13 – Tolerances on width for cold-rolled flat products.14
Table 14 – Tolerances on width for hot-rolled flats .14
Table 15 – Tolerances on flatness for hot-rolled strip and sheet .14
Table 16 – Tolerances on flatness for hot-rolled plate.15
Table 17 – Tolerances on flatness for cold-rolled flat products.15
Table 18 – Tolerances on length for hot-rolled sheet.15
Table 19 – Tolerances on length for hot-rolled plate .16
Table 20 – Tolerances on length for cold-rolled flat products .16
Table 21 – Tolerances on straightness for hot-rolled flats .17
Table 22 – Tolerances on straightness for hot-rolled rounds and squares .17
– 4 – 60404-8-10 © IEC:2009
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MAGNETIC MATERIALS –
Part 8-10: Specifications for individual materials –
Magnetic materials (iron and steel)
for use in relays
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Com
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.