EN 60512-17-3:2010

SLOVENSKI STANDARD
01-december-2010
.RQHNWRUML]DHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO3UHVNXãDQMH
NDEHOVNLKREMHPN3UHVNXVF2GSRUQRVWNDEHOVNLKREMHPNSURWLYOHþHQMX
QDWH]QD,(&
Connectors for electronic equipment - Tests and measurements - Part 17-3: Cable
clamping tests - Test 17c: Cable clamp resistance to cable pull (tensile) (IEC 60512-17-
3:2010)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 17-3:
Prüfungen der Kabelabfangung - Prüfung 17c: Widerstandsfähigkeit der Kabelabfangung
gegen axialen Zug (IEC 60512-17-3:2010)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 17-3: Essais
de maintien des câbles - Essai 17c: Résistance de la pince de maintien des câbles au
tirage (CEI 60512-17-3:2010)
Ta slovenski standard je istoveten z: EN 60512-17-3:2010
ICS:
21.060.70 Sponke in skobe Clamps and staples
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60512-17-3
NORME EUROPÉENNE
September 2010
EUROPÄISCHE NORM
ICS 31.220.01
English version
Connectors for electronic equipment -
Tests and measurements -
Part 17-3: Cable clamping tests -
Test 17c: Cable clamp resistance to cable pull (tensile)
(IEC 60512-17-3:2010)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Essais et mesures - Einrichtungen - Mess- und Prüfverfahren -
Partie 17-3: Essais de maintien Teil 17-3: Prüfungen der Kabelabfangung -
des câbles - Prüfung 17c: Widerstandsfähigkeit
Essai 17c: Résistance de la pince der Kabelabfangung gegen axialen Zug
de maintien des câbles au tirage (IEC 60512-17-3:2010)
(CEI 60512-17-3:2010)
This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-17-3:2010 E
Foreword
The text of document 48B/2156/FDIS, future edition 1 of IEC 60512-17-3, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-17-3 on 2010-09-01
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60512-17-3:2010 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60512-17-3:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60512-1-1 - Connectors for electronic equipment - Tests EN 60512-1-1 -
and measurements -
Part 1-1: General examination - Test 1a:
Visual examination
IEC 60512-17-3 ®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment – Tests and measurements –
Part 17-3: Cable clamping tests – Test 17c: Cable clamp resistance to cable pull
(tensile)
Connecteurs pour équipements électroniques – Essais et mesures –
Partie 17-3: Essais de maintien des câbles – Essai 17c: Résistance de la pince
de maintien des câbles au tirage

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
E
CODE PRIX
ICS 31.220.01 ISBN 978-2-88910-956-2
– 2 – 60512-17-3 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 17-3: Cable clamping tests –
Test 17c: Cable clamp resistance to cable pull (tensile)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in
...