EN IEC 60512-11-1:2019
(Main)Connectors for electrical and electronic equipment - Tests and measurements - Part 11-1: Climatic tests - Test 11a - Climatic sequence
Connectors for electrical and electronic equipment - Tests and measurements - Part 11-1: Climatic tests - Test 11a - Climatic sequence
IEC 60512-11-1:2019 when required by the detail (product) specification, is used for testing connectors within the scope of IEC technical committee 48. This test may also be used for similar devices (i.e. when the degradation mechanisms are the same) when specified in a detail (product) specification. The object of this test is to define a standard test method to assess the ability of connectors to function in a specified manner, in a specified environment which might be encountered during normal use, including storage. This document provides a standard composite test method for determining the suitability of connectors when subjected to environmental conditions consisting of a sequence of temperature, humidity and, where required, low air pressure environmental stresses. Key words: Connectors, Climatic Tests
Steckverbinder für elektrische und elektronische Einrichtungen - Prüfungen und Messungen - Teil 11-1: Klimatische Prüfungen - Prüfung 11a - Klimafolge
Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie 11-1: Essais climatiques - Essai 11a - Séquence climatique
IEC 60512-11-1:2019 est utilisée, lorsque la spécification particulière (de produit) l'exige, pour soumettre à l'essai des connecteurs qui entrent dans le domaine d'application du comité d'études 48 de l'IEC. Cet essai peut aussi être utilisé sur des dispositifs similaires (c'est-à-dire lorsque les mécanismes de dégradation sont les mêmes) lorsqu'une spécification particulière (de produit) l'indique. L'objet de cet essai est de définir une méthode d'essai normalisée pour évaluer l'aptitude des connecteurs à fonctionner de manière spécifiée dans un environnement spécifié qui pourrait être rencontré dans des conditions normales d'utilisation, y compris le stockage. Le présent document fournit une méthode d'essai composite normalisée pour déterminer l'aptitude des connecteurs soumis à des conditions d'environnement consistant en une séquence de contraintes climatiques comportant température, humidité, et si cela est exigé, basse pression. Mots clés: connecteurs, Essais climatiques
Konektorji za električno in elektronsko opremo - Preskusi in meritve - 11-1. del: Klimatski preskusi - Preskus 11a - Klimatsko zaporedje (IEC 60512-11-1:2019)
Ta del standarda IEC 60512 se uporablja, če tako zahteva podrobna specifikacija (izdelka), za preskušanje konektorjev na področju uporabe določil tehničnega odbora IEC 48. Ta preskus se lahko uporablja tudi za podobne naprave (npr. če imajo enak mehanizem degradacije), če je tako določeno v podrobni specifikaciji (izdelka).
Cilj tega preskusa je, da določi standardno preskusno metodo za oceno zmožnosti konektorjev, da delujejo na določen način, v določenem okolju, kot bo to pri običajni uporabi, vključno s shranjevanjem.
Ta dokument zagotavlja standardno sestavljeno preskusno metodo za določanje primernosti konektorja, izpostavljenega okoljskim pogojem, ki so sestavljeni iz zaporedja okoljskih obremenitev, kot so temperatura, vlažnost in (če je to ustrezno) nizek zračni tlak.
Vrstni red izpostavljanja obremenitvam in pogojem za spremembo iz enega koraka v drugega je bil izbran tako, da pospeši, poveča ter omogoči morebitne interakcije enakih mehanizmov degradacije, kot so tisti, do katerih pride pri naravnih podnebnih razmerah.
Pri sestavljenem preskusu so konektorski preskušanci izpostavljeni okoljskim preskusom v standardnem vrstnem redu in so kategorizirani glede na njihove podnebne kategorije, kot je to določeno v podrobni specifikaciji (izdelka), vendar pa je tretja skupina številk uporabljena kot oznaka števila ciklov v 5. koraku preskusa s ciklično vlažno vročino v skladu s standardom IEC 60512-11-12.
Če so potrebne spremembe, podrobna specifikacija ustreznega konektorja (izdelka) podaja potrebne informacije za vsak korak metode.
Ta preskus je pogosto določen tako, da sledi drugim preskusom mehanskih obremenitev, na primer preskusom robustnosti priključkov, preskusom primernosti za spajkanje ali preskusom z udarci in vibracijami, kot sredstvo za določanje, ali je tesnitev preskušanca poškodovana.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2019
Nadomešča:
SIST EN 60512-11-1:2002
Konektorji za električno in elektronsko opremo - Preskusi in meritve - 11-1. del:
Klimatski preskusi - Preskus 11a - Klimatsko zaporedje (IEC 60512-11-1:2019)
Connectors for electrical and electronic equipment - Tests and measurements - Part 11-
1: Climatic tests - Test 11a - Climatic sequence (IEC 60512-11-1:2019)
Elektrisch-mechanische Bauelemente für elektronische Einrichtungen - Mess- und
Prüfverfahren - Teil 11-1: Klimatische Prüfungen - Prüfung 11a: Klimafolge (IEC 60512-
11-1:2019)
Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie
11-1: Essais climatiques - Essai 11a - Séquence climatique (IEC 60512-11-1:2019)
Ta slovenski standard je istoveten z: EN IEC 60512-11-1:2019
ICS:
31.220.01 Elektromehanske Electromechanical
komponente (sestavni deli, components in general
gradniki) na splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60512-11-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2019
ICS 31.220.01 Supersedes EN 60512-11-1:1999
English Version
Connectors for electrical and electronic equipment - Tests and
measurements - Part 11-1: Climatic tests - Test 11a - Climatic
sequence
(IEC 60512-11-1:2019)
Connecteurs pour équipements électriques et électroniques Elektrisch-mechanische Bauelemente für elektronische
- Essais et mesures - Partie 11-1: Essais climatiques - Einrichtungen - Mess- und Prüfverfahren - Teil 11-1:
Essai 11a - Séquence climatique Klimatische Prüfungen - Prüfung 11a: Klimafolge
(IEC 60512-11-1:2019) (IEC 60512-11-1:2019)
This European Standard was approved by CENELEC on 2019-06-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60512-11-1:2019 E
European foreword
The text of document 48B/2688/CDV, future edition 2 of IEC 60512-11-1, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60512-11-1:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-03-20
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-06-20
document have to be withdrawn
This document supersedes EN 60512-11-1:1999.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60512-11-1:2019 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 2013 Environmental testing - Part 1: General EN 60068-1 2014
and guidance
IEC 60068-2-1 2007 Environmental testing - Part 2-1: Tests - EN 60068-2-1 2007
Test A: Cold
IEC 60068-2-2 2007 Environmental testing - Part 2-2: Tests - EN 60068-2-2 2007
Test B: Dry heat
IEC 60068-2-13 1983 Basic environmental testing procedures - EN 60068-2-13 1999
Part 2-13: Tests - Test M: Low air
pressure
IEC 60068-2-30 - Environmental testing - Part 2-30: Tests - EN 60068-2-30 -
Test Db: Damp heat, cyclic (12 h + 12 h
cycle)
IEC 60068-2-61 1991 Environmental testing - Part 2-61: Test EN 60068-2-61 1993
methods - Test Z/ABDM:Climatic
sequence
IEC 60512-1 - Connectors for electrical and electronic EN IEC 60512-1 -
equipment - Tests and measurements -
Part 1: Generic specification
IEC 60512-1-101 - Connectors for electronic equipment - - -
Tests and measurements - Part 1-101:
Blank detail specification
IEC 60512-1-1 - Connectors for electronic equipment - EN 60512-1-1 -
Tests and measurements - Part 1-1:
General examination - Test 1a: Visual
examination
IEC 60512-2-1 - Connectors for electronic equipment - EN 60512-2-1 -
Tests and measurements - Part 2-1:
Electrical continuity and contact
resistance tests - Test 2a: Contact
resistance - Millivolt level method
Publication Year Title EN/HD Year
IEC 60512-2-2 - Connectors for electronic equipment - EN 60512-2-2 -
Tests and measurements - Part 2-2:
Electrical continuity and contact
resistance tests - Test 2b: Contact
resistance - Specified test current method
IEC 60512-3-1 - Connectors for electronic equipment - EN 60512-3-1 -
Tests and measurements - Part 3-1:
Insulation tests - Test 3a: Insulation
resistance
IEC 60512-4-1 - Connectors for electronic equipment - EN 60512-4-1 -
Tests and measurements - Part 4-1:
Voltage stress tests - Test 4a: Voltage
proof
IEC 60512-11-9 - Connectors for electronic equipment - EN 60512-11-9 -
Tests and measurements - Part 11-9:
Climatic tests - Test 11i: Dry heat
IEC 60512-11-10 - Connectors for electronic equipment - EN 60512-11-10 -
Tests and measurements - Part 11-10:
Climatic tests - Test 11j: Cold
IEC 60512-11-11 - Connectors for electronic equipment - EN 60512-11-11 -
Tests and measurements - Part 11-11:
Climatic tests - Test 11k: Low air pressure
IEC 60512-11-12 - Connectors for electronic equipment - EN 60512-11-12 -
Tests and measurements - Part 11-12:
Climatic tests - Test 11m: Damp heat,
cyclic
IEC 60512-13-1 - Connectors for electronic equipment - EN 60512-13-1 -
Tests and measurements - Part 13-1:
Mechanical operation tests - Test 13a:
Engaging and separating forces
IEC 60512-13-2 - Connectors for electronic equipment - EN 60512-13-2 -
Tests and measurements - Part 13-2:
Mechanical operation tests - Test 13b:
Insertion and withdrawal forces
IEC 60512-17-1 - Connectors for electronic equipment - EN 60512-17-1 -
Tests and measurements - Part 17-1:
Cable clamping tests - Test 17a: Cable
clamp robustness
IEC 60512-17-2 - Connectors for electronic equipment - EN 60512-17-2 -
Tests and measurements - Part 17-2:
Cable clamping tests - Test 17b: Cable
clamp resistance to cable rotation
IEC 60512-17-3 - Connectors for electronic equipment - EN 60512-17-3 -
Tests and measurements - Part 17-3:
Cable clamping tests - Test 17c: Cable
clamp resistance to cable pull (tensile)
IEC 60512-17-4 - Connectors for electronic equipment - EN 60512-17-4 -
Tests and measurements - Part 17-4:
Cable clamping tests - Test 17d: Cable
clamp resistance to cable torsion
IEC 60512-11-1 ®
Edition 2.0 2019-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electrical and electronic equipment – Tests and measurements –
Part 11-1: Climatic tests – Test 11a – Climatic sequence
Connecteurs pour équipements électriques et électroniques – Essais et mesures –
Partie 11-1: Essais climatiques – Essai 11a – Séquence climatique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.01 ISBN 978-2-8322-6814-8
– 2 – IEC 60512-11-1:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 8
4 Preparations . 8
4.1 Test equipment . 8
4.2 Preparation of the specimen . 8
4.3 Mounting of specimen . 8
5 Test method . 8
5.1 Preconditioning . 8
5.2 Initial measurements . 9
5.3 Tests (conditioning) . 9
5.3.1 General . 9
5.3.2 Step 1: dry heat . 9
5.3.3 Step 2: damp heat, cyclic (first cycle) . 9
5.3.4 Step 3: cold . 9
5.3.5 Step 4 (optional): low air pressure . 9
5.3.6 Step 5: damp heat, cyclic, remaining cycle(s) . 10
5.4 Recovery . 10
5.5 Final measurements . 10
6 Details to be specified . 10
IEC 60512-11-1:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 11-1: Climatic tests – Test 11a – Climatic sequence
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.