Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers

Applies to the following main measuring methods: automatic null balance, thermomagnetic or mangetic wind and differential pressure or ""Quinke"". Deals with ancillary units and applies to analyzers installed both indoors and outdoors. Indends to specify terminology and definitions, unify methods, specify tests and provide basic documents to support the application of standards of quality assurance ISO 9001, ISO 9002 and ISO 9003.

Gasanalysatoren - Angabe zum Betriebsverhalten - Teil 3: Paramagnetische Sauerstoffanalysatoren

Analyseurs de gaz - Expression des qualités de fonctionnement - Partie 3: Analyseurs d'oxygène paramagnétiques

S'applique à trois méthodes principales de mesure: équilibrage automatique à méthode de zéro "vent" thermomagnétique ou magnétique et pression différentielle ou méthode de "Quinke". Traite des unités auxiliaires et s'applique aux analyseurs installés à l'intérieur et à l'extérieur. A pour objet de spécifier la terminologie et les définitions, unifier les méthodes, spécifier les essais et de stipuler des documents de base permettant d'appliquer les normes d'assurance de la qualité ISO 9001, ISO 9002 et ISO 9003.

Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers

General Information

Status: Withdrawn
Publication Date: 18-Jan-1999

ICS: 29.260.99 - Other electrical equipment for working in special conditions

Technical Committee: CLC/SR 65B - Devices & process analysis
Drafting Committee: IEC/SC 65B - IEC_SC_65B
Parallel Committee: IEC/SC 65D - IEC_SC_65D

Current Stage: 9960 - Withdrawal effective - Withdrawal
Start Date: 01-May-2005
Completion Date: 01-May-2005

Ref Project: SIST EN 61207-3:2001 - Gas analyzers - Expression of performance -- Part 3: Paramagnetic oxygen analyzers

Relations

Replaced By: EN 61207-3:2002 - Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers
Effective Date: 28-Jan-2023

Refers: EN 60654-1:1993 - Industrial-process measurement and control equipment - Operating conditions - Part 1: Climatic conditions
Effective Date: 03-Feb-2026

Refers: EN 61115:1993 - Expression of performance of sample handling systems for process analyzers
Effective Date: 03-Feb-2026

Refers: EN 61207-1:1994 - Expression of performance of gas analyzers - Part 1: General
Effective Date: 03-Feb-2026

Buy Documents

Standard

EN 61207-3:2001

English language (31 pages)

Preview

e-Library read for

AI-Chat

1 day

Create e-Library subscription and get permanent access to the document. Subscriptions are available for: 29 29.260 29.260.99

Get Certified

Connect with accredited certification bodies for this standard

Intertek Testing Services NA Inc.

Intertek certification services in North America.

ANAB United States Verified

Visit Website

UL Solutions

Global safety science company with testing, inspection and certification.

ANAB United States Verified

Visit Website

ANCE

Mexican certification and testing association.

EMA Mexico Verified

Visit Website

Frequently Asked Questions

What is EN 61207-3:1999?

EN 61207-3:1999 is a standard published by CLC. Its full title is "Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers". This standard covers: Applies to the following main measuring methods: automatic null balance, thermomagnetic or mangetic wind and differential pressure or ""Quinke"". Deals with ancillary units and applies to analyzers installed both indoors and outdoors. Indends to specify terminology and definitions, unify methods, specify tests and provide basic documents to support the application of standards of quality assurance ISO 9001, ISO 9002 and ISO 9003.

What is the scope of EN 61207-3:1999?

What ICS categories does EN 61207-3:1999 belong to?

EN 61207-3:1999 is classified under the following ICS (International Classification for Standards) categories: 29.260.99 - Other electrical equipment for working in special conditions. The ICS classification helps identify the subject area and facilitates finding related standards.

What standards are related to EN 61207-3:1999?

EN 61207-3:1999 has the following relationships with other standards: It is inter standard links to EN 61207-3:2002, EN 60654-1:1993, EN 61115:1993, EN 61207-1:1994. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

How can I access EN 61207-3:1999?

EN 61207-3:1999 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)

EN 61207-3:2001

SLOVENSKI STANDARD
01-april-2001
Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen
analyzers
Gas analyzers - Expression of performance -- Part 3: Paramagnetic oxygen analyzers
Gasanalysatoren - Angabe zum Betriebsverhalten -- Teil 3: Paramagnetische
Sauerstoffanalysatoren
Analyseurs de gaz - Expression des qualités de fonctionnement -- Partie 3: Analyseurs
d'oxygène paramagnétiques
Ta slovenski standard je istoveten z: EN 61207-3:1999
ICS:
71.040.40 Kemijska analiza Chemical analysis
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

CLC

EN 50617-1:2024(Main)

Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits

SIST EN 50617-1:2025

This document specifies the technical parameters of track circuits associated with the interference current emissions limits for RST in the context of interoperability defined in the form of Frequency Management in ERA/ERTMS/033281 v4.0. The limits for compatibility between rolling stock and track circuits addressed in this document allow provision for known interference phenomena linked to traction power supply including associated protection (over voltage, short-circuit current and basic transient effects like in-rush current and power cut-off), and other known sources of interference. This document is intended to be used to assess compliance of track circuits and other forms of train detection systems using the rails as part of their detection principles, in the context of the European Directive on the interoperability of the trans-European railway system and the associated technical specification for interoperability relating to the control-command and signalling track-side subsystems. The document describes technical parameters to consider for achieving the compatibility of the track circuit with the emissions limits defined in the frequency management for rolling stock (ERA/ERTMS/033281 v4.0). These parameters are structured and allocated according to their basic references as follows: - technical track circuit parameters; - train based parameters; - track based parameters; - environmental and other parameters including EMC. Each parameter is defined by a short general description, the definition of the requirement, the relation to other standards and a procedure to show the fulfilment of the requirement as far as necessary. An overview of the safety relevance of each parameter is given - in the context of this document - in a separate table. This document is applicable to track circuits on all lines, including non-electrified lines. However, for track circuits intended to be installed only on non-electrified lines, some parameters can be disapplied.

Standard
82 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 62819:2023/AC:2024-03(Corrigendum)

Live working - Eye, face and head protectors against the effects of electric arc - Performance requirements and test methods

SIST EN IEC 62819:2023/AC:2024

Corrigendum
3 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 62819:2023(Main)

Live working - Eye, face and head protectors against the effects of electric arc - Performance requirements and test methods

SIST EN IEC 62819:2023

This document is applicable to eye, face and head protectors used in work where there is a risk of exposure to an electric arc hazard. Such protectors consist of one or several devices (e.g. hood, goggles, balaclavas, face shields, helmets, etc.), which might need to be combined together in order to give protection to eye, face and head for the intended use. This document covers the performance requirements for protectors and single protective devices considering thermal, optical and mechanical hazards of an electric arc. Because of the limitations of test apparatus at very high energy arcs, no arc rating above 4 100 kJ/m2 (100 cal/cm2) can be assigned to protectors. This document does not cover protection against electric shock, noise, the consequences of physical and mental shock and the toxic influences caused by an electric arc. This document does not cover protectors for work intentionally using an electric arc, e.g. arc welding, plasma torch. This document does not cover face-screens for the reduction of an electric field inside conductive clothing in accordance with IEC 60895. Any other claims of the manufacturer for protection against other hazards to eye or face (e.g. welding radiation, hazards occurring during fire-fighting) are outside the scope of the document. Products designed and manufactured in accordance with this document contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use.

Standard
52 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 61318:2021(Main)

Live working - Methods for assessment of defects and verification of performance applicable to tools, devices and equipment

SIST EN IEC 61318:2021

This document defines methods to assess defects and to verify that products after the manufacturer process meet the requirements of the corresponding product standard. The principles of assessment of defects for live working products are detailed in this document to assist product standard developers in prescribing the best means to achieve suitable quality of every finished tool, device and piece of equipment. The following elements are not covered by the present document, but are included in each product standard: - type tests; - provisions and description for routine, sampling and acceptance tests; - identification and classification of defects; - risk analysis. This document does not cover conformity assessment of commercial shipments or certifications.

Standard
18 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 61243-1:2021(Main)

Live working - Voltage detectors - Part 1: Capacitive type to be used for voltages exceeding 1 kV AC

SIST EN IEC 61243-1:2021

IEC 61243-1:2021 is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 800 kV AC, and frequencies of 50 Hz and/or 60 Hz. This document applies only to voltage detectors of capacitive type used in contact with the bare part to be tested, as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this document (see 4.4.2.1 for general design). Other types of voltage detectors are not covered by this document. Self ranging voltage detectors (formally "multi range voltage detectors") are not covered by this document. Some restrictions or formal interdictions on their use are applicable in case of switchgear of IEC 62271 series design, due to insulation coordination, on overhead line systems of electrified railways (see Annex B) and systems without neutral reference. For systems without neutral reference, the insulating level is adapted to the maximum possible voltage to the earth (ground). Products designed and manufactured according to this document contribute to the safety of users provided they are used by persons trained for the work, in accordance with the hot stick working method and the instructions for use. Except where otherwise specified, all the voltages defined in this document refer to values of phase-to-phase voltages of three-phase systems. In other systems, the applicable phase-to-phase or phase-to-earth (ground) voltages are used to determine the operating voltage. This third edition cancels and replaces the second edition published in 2003 and Amend-ment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The scope is more precise, stating that only bare contact to the part to be tested is reliable for these contact voltage detectors. The rationale is that tests on painted or coated conductors have led to wrong indications, as this non-conductive paint or coat acts as a capacitor with different capacity according to the thickness. This capacity has an effect on the threshold voltage. b) A contact probe is introduced as a new type of non-conductive contact electrode. c) A new type "exclusively outdoor type" has been defined and implemented into the requirements and test procedure. d) A selector for voltage and frequency is allowed if foreseeable misuse is excluded. e) The marking for voltage detectors with low interference voltage has been made more precise. f) The indication groups have been made more precise and requirements and tests for the "ready to operate state" and "stand-by state" added. g) Requirements and tests for electromagnetic compatability have been implemented. h) An example for good electrical connection for the tests is introduced.

Standard
82 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 61472-2:2021(Main)

Live working - Minimum approach distances - Part 2: Method of determination of the electrical component distance for AC systems from 1,0 kV to 72,5 kV

SIST EN IEC 61472-2:2021

IEC 61472-2:2021 specifies a method for determining the electrical component of the minimum approach distances for live working, for AC systems 1 kV up to and including 72,5 kV. This document addresses system overvoltages and the working air distances between equipment and/or workers at different potentials. The withstand voltage and minimum approach distances determined by the method described in this document can be used only if the following working conditions prevail:
workers are trained for, and skilled in, working live lines or close to live conductors or equipment;
the operating conditions are adjusted so that the statistical overvoltage does not exceed the value selected for the determination of the required withstand voltage;
transient overvoltages are the determining overvoltages;
tool insulation has no continuous film of moisture present on the surface;
no lightning is observed within 10 km of the work site;
allowance is made for the effect of the conducting components of tools.

Standard
18 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 61496-2:2020(Main)

Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)

SIST EN IEC 61496-2:2020

IEC 61496-2:2020 specifies requirements for the design, construction and testing of electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety-related system, employing active opto-electronic protective devices (AOPDs) for the sensing function. Special attention is directed to features which ensure that an appropriate safety-related performance is achieved. An ESPE can include optional safety-related functions, the requirements for which are given in Annex A of IEC 61496-1:2020 and of this document. This document does not specify the dimensions or configurations of the detection zone and its disposition in relation to hazardous parts for any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. Excluded from this document are AOPDs employing radiation at wavelengths outside the range 400 nm to 1 500 nm. This document can be relevant to applications other than those for the protection of persons, for example, the protection of machinery or products from mechanical damage. In those applications, additional requirements can be necessary, for example, when the materials that are to be recognized by the sensing function have different properties from those of persons. This document does not deal with electromagnetic compatibility (EMC) emission requirements. IEC 61496-2:2020 cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Requirements and test procedures in Part 2 that were found to be common to all ESPEs have been moved to Part 1. Test procedures that are dependent on the sensing technology remain in Part 2.

Standard
50 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 61496-1:2020(Main)

Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests

SIST EN IEC 61496-1:2020

IEC 61486-1:2020 specifies general requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons or part of a person as part of a safety-related system. Special attention is directed to functional and design requirements that ensure an appropriate safety-related performance is achieved. An ESPE can include optional safety-related functions, the requirements for which are given in Annex A. This document is intended to be used with a subsequent part of IEC 61496 that provides particular requirements based on the sensing technology. Where a part covering the sensing technology does not exist, IEC TS 62998-1 is used. Where the IEC 61496 series does not contain all necessary provisions, IEC TS 62998-1 is used. It is an additional possibility to combine those aspects covered by the IEC 61496 series in addition to IEC TS 62998-1. This document does not specify the dimensions or configuration of the detection zone and its disposition in relation to hazards in any particular application, nor what constitutes a hazardous state of any machine. It is restricted to the functioning of the ESPE and how it interfaces with the machine. While a data interface can be used to control optional safety-related ESPE functions (Annex A), this document does not provide specific requirements. Requirements for these safety-related functions can be determined by consulting other standards (for example, IEC 61508 (all parts), IEC TS 62046, IEC 62061, and ISO 13849-1). This document can be relevant to applications other than those for the protection of persons, for example for the protection of machinery or products from mechanical damage. In those applications, different requirements can be appropriate, for example when the materials that have to be recognized by the sensing function have different properties from those of persons. This document does not deal with requirements for ESPE functions not related to the protection of persons (e.g. using sensing unit data for navigation). This document does not deal with electromagnetic compatibility (EMC) emission requirements. IEC 61486-1:2020 cancels and replaces the third edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) It has been clarified that some requirements for ESPEs that are dependent on sensing technology are not included in IEC 61496-1. They are provided in a subsequent part of IEC 61496. b) Requirements for protection against environmental influences from subsequent parts of IEC 61496 that are common to all ESPEs have been consolidated into IEC 61496-1. c) Some test procedures in IEC 61496-1 were incomplete. They have been expanded with more detail and step by step procedures. d) Some requirements and procedures in IEC 61496-1 are now covered by new generic machine safety standards. The requirements in IEC 61496-1 have been harmonized with references to the new generic standards.

Standard
63 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 60895:2020(Main)

Live working - Conductive clothing

SIST EN IEC 60895:2020

IEC 60895:2020 is applicable to conductive clothing, worn during live working (especially bare-hand working) on AC and DC electrical installations, to provide electrical continuity between all parts of the clothing and a reduction of electric field inside the clothing. This document is applicable to conductive clothing assembled from a conductive garment (jackets and trousers or coveralls forming a one-piece garment) and from conductive component parts (gloves, hoods or helmets, shoes or boots, overshoe socks and socks) in electrical systems with nominal voltage up to 1 000 kV AC and up to ±800 kV DC. This document does not indicate values of protection from the effects of the electric arc, because any value indicated would not guarantee the necessary protection from the effects of electric arcs, or the operator would need to wear very heavy and rigid conductive clothing, which would not allow the execution of the work in safety. The products designed and manufactured according to this document contribute to the safety of the users provided they are used by persons trained for the work, in accordance with the live working methods and the instructions for use. This third edition cancels and replaces the second edition, published in 2002. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) increase of the use up to 1 000 kV AC and ±800 kV DC; b) introduction of two classes of conductive clothing with different electrical requirements; c) revision of the electrical requirements of conductive clothing; d) definition of specific resistance values for each component part of the conductive clothing; e) introduction of conductive helmet and conductive scarf as component parts of conductive clothing; f) introduction of mechanical requirements and new tests for fabrics; g) update of the cleaning test procedures; h) revision of the efficiency test of the conductive clothing to improve the feasibility and repeatability; i) preparation of the elements of classification of defects, and general application of IEC 61318:2007; j) the normative Annex B for the classification of tests has been replaced by normative Annex C for the general type tests procedure, the normative Annex D for the classification of defects and the informative Annex E providing the justification for the classification of defects; k) the normative Annex C on sampling procedure has been deleted (not applicable according to IEC 61318:2007); l) modification of the recommended frequency of the periodic tests.

Standard
72 pages
English language
e-Library read for
AI-Chat
1 day

CLC

EN IEC 60900:2018/AC:2020-05(Corrigendum)

Live working - Hand tools for use up to 1 000 V AC and 1 500 V DC

SIST EN IEC 60900:2018/AC:2020

TAN - // IEC Corrigendum

Corrigendum
3 pages
English and French language
e-Library read for
AI-Chat
1 day

Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers

Gasanalysatoren - Angabe zum Betriebsverhalten - Teil 3: Paramagnetische Sauerstoffanalysatoren

Analyseurs de gaz - Expression des qualités de fonctionnement - Partie 3: Analyseurs d'oxygène paramagnétiques

Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers

General Information

Relations

Buy Documents

EN 61207-3:2001

Get Certified

Intertek Testing Services NA Inc.

UL Solutions

ANCE

Frequently Asked Questions

Standards Content (Sample)

Questions, Comments and Discussion

This May Also Interest You