EN IEC 60695-2-11:2021
(Main)Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end products (GWEPT)
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end products (GWEPT)
This part of IEC 60695 specifies a test method on an end product. It is intended to simulate the effects of thermal stresses produced by an electrically heated source to represent a fire hazard. This test method is used to check that, under defined test conditions, an end product exposed to an electrically heated source has either a limited ability to ignite or, if it ignites, a limited ability to propagate flame. However, the fire hazard analysis, the flammability aspects and the flame spreading to other products are not covered by this document. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-11: Prüfverfahren mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entflammbarkeit von Enderzeugnissen (GWEPT)
Essais relatifs aux risques du feu - Partie 2-11: Essais au fil incandescent/chauffant - Méthode d'essai d'inflammabilité pour produits finis (GWEPT)
IEC 60695-2-11:2021 est disponible sous forme de IEC 60695-2-11:2021 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente. L'IEC 60695-2-11:2021 spécifie une méthode d’essai applicable au produit fini. Elle est destinée à simuler les effets des contraintes thermiques produites par une source chauffée électriquement afin de représenter un danger d’incendie. La présente méthode d’essai permet de vérifier que, dans des conditions d’essai définies, un produit fini exposé à une source chauffée électriquement présente une aptitude limitée à s’enflammer ou, s’il s’enflamme, une aptitude limitée à propager la flamme. Cependant, le présent document ne traite pas de l’analyse du danger d'incendie, des aspects d’inflammabilité et de propagation de flammes à d’autres produits. La présente publication fondamentale de sécurité, fondée sur la ou les méthodes d'essai de sécurité, est essentiellement destinée à être utilisée par les comités d’études dans le cadre de l’élaboration de publications de sécurité conformément aux principes établis dans le Guide IEC 104 et le Guide ISO/IEC 51. L’une des responsabilités d’un comité d’études consiste, le cas échéant, à utiliser les publications fondamentales de sécurité dans le cadre de l’élaboration de ses publications. Cette norme doit être utilisée conjointement avec l’IEC 60695-2-10. Cette troisième édition annule et remplace la deuxième édition parue en 2014. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente: a) ajout à l’Article 3 de nombreux termes et définitions applicables au présent document.
Preskušanje požarne ogroženosti - 2-11. del: Preskusne metode z žarilno žico - Preskušanje vnetljivosti končnega proizvoda z žarilno žico (GWEPT) (IEC 60695-2-11:2021)
Ta del standarda IEC 60695 določa preskusno metodo za končni proizvod. Namenjena je poustvarjanju učinkov toplotne preobremenitve, ki jo proizvede električno ogrevani vir, s čimer se ponazori požarna ogroženost. Ta preskusna metoda se uporablja za preverjanje, ali ima pod opredeljenimi preskusnimi pogoji končni proizvod, ki je izpostavljen električno ogrevanem viru, omejeno sposobnost vžiga ali, če se vžge, omejeno sposobnost širjenja plamena. Vendar pa v tem dokumentu niso zajeti analiza požarne ogroženosti, vidiki vnetljivosti in širjenje plamena na druge proizvode. Ta osnovna varnostna publikacija, ki se osredotoča na varnostne preskusne metode, je namenjena predvsem tehničnim odborom za pripravo varnostnih publikacij v skladu z načeli vodil IEC 104 in ISO/IEC 51. Ena od dolžnosti tehničnega odbora je, da med pripravo publikacij uporablja osnovne varnostne publikacije, kadar je to primerno.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2022
Nadomešča:
SIST EN 60695-2-11:2014
Preskušanje požarne ogroženosti - 2-11. del: Preskusne metode z žarilno žico -
Preskušanje vnetljivosti končnega proizvoda z žarilno žico (GWEPT) (IEC 60695-2-
11:2021)
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire
flammability test method for end products (GWEPT) (IEC 60695-2-11:2021)
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-11: Prüfverfahren mit dem Glühdraht
- Prüfung mit dem Glühdraht zur Entflammbarkeit von Enderzeugnissen (GWEPT) (IEC
60695-2-11:2021)
Essais relatifs aux risques du feu - Partie 2-11: Essais au fil incandescent/chauffant -
Méthode d'essai d'inflammabilité pour produits finis (GWEPT) (IEC 60695-2-11:2021)
Ta slovenski standard je istoveten z: EN IEC 60695-2-11:2021
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60695-2-11
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2021
ICS 13.220.40; 29.020 Supersedes EN 60695-2-11:2014 and all of its
amendments and corrigenda (if any)
English Version
Fire hazard testing - Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test method for end products
(GWEPT)
(IEC 60695-2-11:2021)
Essais relatifs aux risques du feu - Partie 2-11: Essais au fil Prüfungen zur Beurteilung der Brandgefahr - Teil 2-11:
incandescent/chauffant - Méthode d'essai d'inflammabilité Prüfverfahren mit dem Glühdraht - Prüfung mit dem
pour produits finis (GWEPT) Glühdraht zur Entflammbarkeit von Enderzeugnissen
(IEC 60695-2-11:2021) (GWEPT)
(IEC 60695-2-11:2021)
This European Standard was approved by CENELEC on 2021-12-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60695-2-11:2021 E
European foreword
The text of document 89/1536/FDIS, future edition 3 of IEC 60695-2-11, prepared by IEC/TC 89 “Fire
hazard testing” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–09–02
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–12–02
document have to be withdrawn
This document supersedes EN 60695-2-11:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60695-2-11:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60695-1-10 NOTE Harmonized as EN 60695-1-10
IEC 60695-1-11 NOTE Harmonized as EN 60695-1-11
IEC 60695-2-12 NOTE Harmonized as EN 60695-2-12
IEC 60695-2-13 NOTE Harmonized as EN IEC 60695-2-13
IEC 60335-1 NOTE Harmonized as EN 60335-1
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by
(mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60695-2-10 - Fire hazard testing - Part 2–10: EN IEC 60695-2-10 -
Glowing/hot-wire based test methods -
Glow-wire apparatus and common test
procedure
IEC 60695-4 2012 Fire hazard testing - Part 4: Terminology EN 60695-4 2012
concerning fire tests for electrotechnical
products
ISO 13943 2017 Fire safety - Vocabulary EN ISO 13943 2017
IEC 60695-2-11 ®
Edition 3.0 2021-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
HORIZONTAL PUBLICATION
PUBLICATION HORIZONTALE
Fire hazard testing –
Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test
method for end products (GWEPT)
Essais relatifs aux risques du feu –
Partie 2-11: Essais au fil incandescent/chauffant – Méthode d’essai
d’inflammabilité pour produits finis (GWEPT)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40; 29.020 ISBN 978-2-8322-1011-0
– 2 – IEC 60695-2-11:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Test specimens . 8
4.1 General . 8
4.2 Complete end product . 8
4.3 Partial end product (alternative) . 9
4.4 Test considerations and limitations associated with the specimen
configuration . 9
5 Test apparatus . 10
6 Verification of the temperature measuring system . 10
7 Conditioning . 10
7.1 Conditioning of test specimens . 10
7.2 Conditioning of specified layers . 11
7.3 Testing conditions . 11
8 Test procedure . 11
8.1 General . 11
8.2 Test temperatures . 11
8.3 Number of test specimens . 12
9 Observations and measurements . 12
10 Evaluation of test results . 12
11 Test report . 12
12 Information to be given in the relevant product standard . 13
Annex A (informative) Suggested GWEPT temperatures . 14
Bibliography . 16
Figure 1 – Small parts . 10
Figure A.1 – Suggested GWEPT temperatures . 15
Table 1 – Test temperatures . 11
IEC 60695-2-11:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 2-11: Glowing/hot-wire based test methods –
Glow-wire flammability test method for end products (GWEPT)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.