EN IEC 62604-1:2022

SLOVENSKI STANDARD
01-november-2022
Nadomešča:
SIST EN 62604-1:2015
Radiofrekvenčni (SAW) in visokofrekvenčni (BAW) duplekserji ocenjene kakovosti
- 1. del: Splošna specifikacija (IEC 62604-1:2022)
Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed
quality - Part 1: Generic specification (IEC 62604-1:2022)
Oberflächenwellen-(OFW-) und Volumenwellen-(BAW-)Duplexer mit bewerteter Qualität
– Teil 1: Fachgrundspezifikation (IEC 62604-1:2022)
Duplexeurs à ondes acoustiques de surface (OAS) et à ondes acoustiques de volume
(OAV) sous assurance de la qualité - Partie 1: Spécification générique (IEC 62604-
1:2022)
Ta slovenski standard je istoveten z: EN IEC 62604-1:2022
ICS:
31.140 Piezoelektrične naprave Piezoelectric devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62604-1

NORME EUROPÉENNE
EUROPÄISCHE NORM September 2022
ICS 31.140 Supersedes EN 62604-1:2015
English Version
Surface acoustic wave (SAW) and bulk acoustic wave (BAW)
duplexers of assessed quality - Part 1: Generic specification
(IEC 62604-1:2022)
Duplexeurs à ondes acoustiques de surface (OAS) et à Oberflächenwellen-(OFW-) und Volumenwellen-(BAW-
ondes acoustiques de volume (OAV) sous assurance de la )Duplexer mit bewerteter Qualität - Teil 1:
qualité - Partie 1: Spécification générique Fachgrundspezifikation
(IEC 62604-1:2022) (IEC 62604-1:2022)
This European Standard was approved by CENELEC on 2022-08-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62604-1:2022 E

European foreword
The text of document 49/1360/CDV, future edition 2 of IEC 62604-1, prepared by IEC/TC 49
"Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control,
selection and detection" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 62604-1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-05-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-08-15
document have to be withdrawn
This document supersedes EN 62604-1:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62604-1:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 62047-7:2011 NOTE Harmonized as EN 62047-7:2011 (not modified)
IEC 60068-2-10:2005 NOTE Harmonized as EN 60068-2-10:2005 (not modified)
IEC 62604-2:2017 NOTE Harmonized as EN IEC 62604-2:2018 (not modified)
IEC 60862-1:2015 NOTE Harmonized as EN 60862-1:2015 (not modified)
IEC 61019-1:2004 NOTE Harmonized as EN 61019-1:2005 (not modified)
IEC 60862-2:2012 NOTE Harmonized as EN 60862-2:2012 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60027 series Letter symbols to be used in electrical EN 60027 series
technology
IEC 60050-561 - International Electrotechnical Vocabulary - - -
Part 561: Piezoelectric, dielectric and
electrostatic devices and associated
materials for frequency control, selection
and detection
IEC 60068-1 2013 Environmental testing - Part 1: General EN 60068-1 2014
and guidance
IEC 60068-2-1 - Environmental testing - Part 2-1: Tests - EN 60068-2-1 -
Test A: Cold
IEC 60068-2-2 - Environmental testing - Part 2-2: Tests - EN 60068-2-2 -
Test B: Dry heat
IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-7 - Basic environmental testing procedures - EN 60068-2-7 -
Part 2-7: Tests - Test Ga and guidance:
Acceleration, steady state
IEC 60068-2-13 - Environmental testing - Part 2-13: Tests - EN IEC 60068-2-13 -
Test M: Low air pressure
IEC 60068-2-14 - Environmental testing - Part 2-14: Tests - EN 60068-2-14 -
Test N: Change of temperature
IEC 60068-2-17 1994 Basic environmental testing procedures - EN 60068-2-17 1994
Part 2-17: Tests - Test Q: Sealing
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 60068-2-30 - Environmental testing - Part 2-30: Tests - EN 60068-2-30 -
Test Db: Damp heat, cyclic (12 h + 12 h
cycle)
IEC 60068-2-31 - Environmental testing - Part 2-31: Tests - EN 60068-2-31 -
Test Ec: Rough handling shocks, primarily
for equipment-type specimens
IEC 60068-2-45 - Basic environmental testing procedures - EN 60068-2-45 -
Part 2-45: Tests - Test XA and guidance:
Immersion in cleaning solvents
IEC 60068-2-52 - Environmental testing - Part 2-52: Tests - EN IEC 60068-2-52 -
Test Kb: Salt mist, cyclic (sodium chloride
solution)
IEC 60068-2-58 - Environmental testing - Part 2-58: Tests - EN 60068-2-58 -
Test Td: Test methods for solderability,
resistance to dissolution of metallization
and to soldering heat of surface mounting
devices (SMD)
IEC 60068-2-64 - Environmental testing - Part 2-64: Tests - EN 60068-2-64 -
Test Fh: Vibration, broadband random
and guidance
IEC 60068-2-78 - Environmental testing - Part 2-78: Tests - EN 60068-2-78 -
Test Cab: Damp heat, steady state
IEC 60122-1 - Quartz crystal units of assessed quality - EN 60122-1 -
Part 1: Generic specification
IEC 60617 - Graphical symbols for diagrams - -
IEC 60642 - Piezoelectric ceramic resonators and - -
resonator units for frequency control and
selection - Chapter I: Standard values and
conditions - Chapter II: Measuring and
test conditions
IEC 60695-11-5 - Fire hazard testing - Part 11-5: Test EN 60695-11-5 -
flames - Needle-flame test method -
Apparatus, confirmatory test arrangement
and guidance
IEC 60749-28 - Semiconductor devices - Mechanical and EN IEC 60749-28 -
climatic test methods - Part 28:
Electrostatic discharge (ESD) sensitivity
testing - Charged device model (CDM) -
device level
IEC 61000-4-2 - Electromagnetic compatibility (EMC) - EN 61000-4-2 -
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61340-3-1 - Electrostatics - Part 3-1: Methods for EN 61340-3-1 -
simulation of electrostatic effects - Human
body model (HBM) electrostatic discharge
test waveforms
IEC 61340-3-2 - Electrostatics - Part 3-2: Methods for EN 61340-3-2 -
simulation of electrostatic effects -
Machine model (MM) electrostatic
discharge test waveforms
IEC 62761 - Guidelines for the measurement method EN 62761 -
of nonlinearity for surface acoustic wave
(SAW) and bulk acoustic wave (BAW)
devices in radio frequency (RF)
IEC 80000 series Quantities and units EN 80000 series
ISO 80000 series Quantities and units EN ISO 80000 series

IEC 62604-1 ®
Edition 2.0 2022-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of

assessed quality –
Part 1: Generic specification
Duplexeurs à ondes acoustiques de surface (OAS) et à ondes acoustiques de

volume (OAV) sous assurance de la qualité –

Partie 1: Spécification générique

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.140 ISBN 978-2-8322-3965-0

– 2 – IEC 62604-1:2022 © IEC 2022
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, units and graphical symbols . 8
3.1 Terms and definitions . 8
3.1.1 General terms . 9
3.1.2 Response characteristics related terms . 11
3.1.3 SAW and BAW duplexers related terms . 15
3.2 Units and graphical symbols . 16
4 Order of precedence of documents . 16
5 Preferred values for ratings and characteristics . 17
5.1 General . 17
5.2 Nominal frequency bands . 17
5.3 Operating temperature ranges, in degrees Celsius (°C) . 17
5.4 Climatic category . 17
5.5 Bump severity . 17
5.6 Vibration severity . 18
5.7 Shock severity . 18
5.8 Fine leak rate . 18
6 Marking . 19
6.1 Duplexer marking . 19
6.2 Package marking . 19
7 Quality assessment procedures . 19
7.1 General . 19
7.2 Primary stage of manufacture . 19
7.3 Structurally similar components . 19
7.4 Subcontracting . 19
7.5 Incorporated components . 20
7.6 Manufacturer’s approval . 20
7.7 Approval procedures . 20
7.7.1 General .
...