EN IEC 61215-2:2021
(Main)Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
IEC 61215-2:2021 is available as IEC 61215-2:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61215-2:2021 lays down requirements for the design qualification of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This document is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. The objective of this test sequence is to determine the electrical characteristics of the module and to show, as far as possible within reasonable constraints of cost and time, that the module is capable of withstanding prolonged exposure outdoors. This second edition of IEC 61215-2 cancels and replaces the first edition of IEC 61215-2 issued in 2016. This edition includes the following significant technical changes with respect to the previous edition: a. Addition of cyclic (dynamic) mechanical load testing (MQT 20). b. Addition of a test for detection of potential-induced degradation (MQT 21). c. Addition of test methods required for bifacial PV modules. d. Addition of test methods required for flexible modules. This includes the addition of the bending test (MQT 22). e. Revision of simulator requirements to ensure uncertainty is both well-defined and minimized. f. Correction to the hot spot endurance test, where the procedure for monolithically integrated (MLI) thin film technologies (MQT 09.2) previously included two sections describing a procedure only appropriate for silicon modules. g. Selection of three diodes, rather than all, for testing in the bypass diode thermal test (MQT 18). h. Removal of the nominal module operating test (NMOT), and associated test of performance at NMOT, from the IEC 61215 series.
Terrestrische Photovoltaik(PV)-Module - Bauarteignung und Bauartzulassung - Teil 2: Prüfverfahren
Modules photovoltaïques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 2: Procédures d'essai
IEC 61215-2:2021 est disponible sous forme de IEC 61215-2:2021 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61215-2:2021 établit les exigences concernant la qualification de conception des modules photovoltaïques terrestres appropriés à un fonctionnement de longue durée dans des climats à l’air libre. Le présent document est destiné à s'appliquer à tous les matériaux de modules à plaque plane pour applications terrestres, tels que les types de modules au silicium cristallin et les modules à couches minces. L'objet de cette séquence d'essais est de déterminer les caractéristiques électriques du module et d’indiquer, dans la mesure du possible avec des contraintes de coût et de temps raisonnables, que le module est capable de supporter une exposition prolongée en site naturel. Cette deuxième édition de l’IEC 61215-2 annule et remplace la première édition de l’IEC 61215‑2 parue en 2016. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente. a. Ajout de l’essai de charge mécanique cyclique (dynamique) (MQT 20 - Module Quality Test, essai de qualité du module). b. Ajout d’un essai de détection de la dégradation induite par le potentiel (MQT 21). c. Ajout de méthodes d’essai exigées pour les modules PV bifaces. d. Ajout de méthodes d’essai exigées pour les modules flexibles. Cette disposition inclut l’ajout de l’essai de flexion (MQT 22). e. Révision des exigences du simulateur pour assurer à la fois la définition appropriée et la réduction le plus possible de l’incertitude. f. Correction de l’essai de tenue à l’échauffement localisé, dont la procédure pour les technologies à couches minces à intégration monolithique (MLI - monolithic integration) (MQT 09.2) comprenait précédemment deux sections décrivant une méthode uniquement adaptée aux modules en silicium. g. Choix de trois diodes, plutôt que de toutes les diodes d’essai, pour l’essai thermique de la diode de dérivation (MQT 18). h. Suppression de l’essai nominal de fonctionnement du module (NMOT - nominal module operating test), et de l’essai associé de performances à la température nominale de fonctionnement du module (NMOT - nominal module operating temperature), issus de la série IEC 61215.
Prizemni fotonapetostni (PV) moduli - Ocena zasnove in odobritev tipa - 2. del: Preskusni postopki
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61215-2:2021
01-junij-2021
Nadomešča:
SIST EN 61215-2:2017
SIST EN 61215-2:2017/AC:2017
SIST EN 61215-2:2017/AC:2018
Prizemni fotonapetostni (PV) moduli - Ocena zasnove in odobritev tipa - 2. del:
Preskusni postopki
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2:
Test procedures
Terrestrische Photovoltaik(PV)-Module - Bauarteignung und Bauartzulassung - Teil 2:
Prüfverfahren
Modules photovoltaïques (PV) pour applications terrestres - Qualification de la
conception et homologation - Partie 2: Procédures d'essai
Ta slovenski standard je istoveten z: EN IEC 61215-2:2021
ICS:
27.160 Sončna energija Solar energy engineering
SIST EN IEC 61215-2:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61215-2:2021
---------------------- Page: 2 ----------------------
SIST EN IEC 61215-2:2021
EUROPEAN STANDARD EN IEC 61215-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 27.160 Supersedes EN 61215-2:2017 and all of its amendments
and corrigenda (if any)
English Version
Terrestrial photovoltaic (PV) modules - Design qualification and
type approval - Part 2: Test procedures
(IEC 61215-2:2021)
Modules photovoltaïques (PV) pour applications terrestres - Terrestrische Photovoltaik(PV)-Module - Bauarteignung und
Qualification de la conception et homologation - Partie 2: Bauartzulassung - Teil 2: Prüfverfahren
Procédures d'essai (IEC 61215-2:2021)
(IEC 61215-2:2021)
This European Standard was approved by CENELEC on 2021-03-31. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61215-2:2021 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61215-2:2021
EN IEC 61215-2:2021 (E)
European foreword
The text of document 82/1829/FDIS, future edition 2 of IEC 61215-2, prepared by IEC/TC 82 "Solar
photovoltaic energy systems" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61215-2:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-12-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-03-31
document have to be withdrawn
This document supersedes EN 61215-2:2017 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61215-2:2021 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 62506 NOTE Harmonized as EN 62506
IEC 62938:2020 NOTE Harmonized as EN IEC 62938:2020 (not modified)
IEC 62941 NOTE Harmonized as EN IEC 62941
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61215-2:2021
EN IEC 61215-2:2021 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated refer
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.