iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61215-2:2017/AC:2018-04

(Corrigendum)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures

Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures

2018-04 AJC: IEC published corrigendum.

Terrestrische Photovoltaik(PV)-Module - Bauarteignung und Bauartzulassung - Teil 2: Prüfverfahren

Modules photovoltaïques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 2: Procédures d'essai

Prizemni fotonapetostni (PV) moduli - Ocena zasnove in odobritev tipa - 2. del: Preskusni postopki - Popravek AC

General Information

Status
Withdrawn
Publication Date
05-Apr-2018
ICS
27.160 - Solar energy engineering
Technical Committee
CLC/TC 82 - Solar photovoltaic energy systems
Drafting Committee
CLC/TC 82 - Solar photovoltaic energy systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
31-Mar-2024
Completion Date
31-Mar-2024
Ref Project
SIST EN 61215-2:2017/AC:2018 - Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures

Relations

Replaced By
EN IEC 61215-2:2021 - Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
Effective Date
13-Apr-2021
Corrects
EN 61215-2:2017 - Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
Effective Date
07-Jun-2022

Buy Standard

EN 61215-2:2017/AC:2018 - BARVEEN 61215-2:2017/AC:2018 - BARVE
PreviousNext
Corrigendum
EN 61215-2:2017/AC:2018 - BARVE
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Prizemni fotonapetostni (PV) moduli - Ocena zasnove in odobritev tipa - 2. del: Preskusni postopki - Popravek ACTerrestrische Photovoltaik(PV)-Module - Bauarteignung und Bauartzulassung - Teil 2: PrüfverfahrenModules photovoltaïques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 2: Procédures d'essaiTerrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures27.160Solar energy engineeringICS:Ta slovenski standard je istoveten z:EN 61215-2:2017/AC:2018-04SIST EN 61215-2:2017/AC:2018en01-junij-2018SIST EN 61215-2:2017/AC:2018SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 61215-2:2017/AC:2018-04
April 2018
ICS 27.160 English Version
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures (IEC 61215-2:2016/COR1:2018)
Modules photovoltaïques (PV) pour applications terrestres -Qualification de la conception et homologation - Partie 2: Procédures d'essai (IEC 61215-2:2016/COR1:2018)
Terrestrische Photovoltaik(PV)-Module - Bauarteignung und Bauartzulassung - Teil 2: Prüfverfahren (IEC 61215-2:2016/COR1:2018) This corrigendum becomes effective on 6 April 2018 for incorporation in the English language version of the EN. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,
B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61215-2:2017/AC:2018-04 ESIST EN 61215-2:2017/AC:2018

Endorsement notice
The text of the corrigendum IEC 61215-2:2016/COR1:2018
was approved by CENELEC as EN 61215-2:2017/AC:2018-04 without any modification.
IEC 61215-2:2016/COR1:2018 – 1 –
 IEC 2018 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE ____________
IEC 61215-2 Edition 1.0
2016-03
TERRESTRIAL PHOTOVOLTAIC (PV) MODULES – DESIGN QUALIFICATION AND TYPE APPROVAL
Part 2: Test procedures
IEC 61215-2 Édition 1.0
2016-03
MODULES PHOTOVOLTAÏQUES (PV) POUR APPLICATIONS TERRESTRES – QUALIFICATION DE LA CONCEPTION ET HOMOLOGATION
Partie 2: Procédures d'essai
CORRIGENDUM 1
Corrections to the French version appear after the English text. Les corrections à la version française sont données après le texte anglais.
4.9.4
Apparatus
Replace:
a)
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 62788-2-1:2023(Main)
Measurement procedures for materials used in photovoltaic modules - Part 2-1: Polymeric materials - Frontsheet and backsheet - Safety requirements
SIST EN IEC 62788-2-1:2024

This document specifies the safety requirements for flexible polymeric frontsheet and backsheet constructions, which are intended for use as relied upon insulation in photovoltaic (PV) modules. In accordance with the corresponding safety requirements in IEC 61730-1 on the PV module level, the test methods and specifications in this document define the specific requirements of the polymeric frontsheet or backsheet constructions on the component level and cover mechanical, electrical, visual and thermal characterization in an unexposed state and/or after ageing. A polymeric frontsheet and backsheet must pass the requirements in this standard for a PV module to pass the design requirements of IEC 61730-1. Compliance with the safety requirements for a frontsheet or backsheet on the component level does not replace the need for a safety qualification of the complete PV module, in which the frontsheet or backsheet is integrated. The appropriate requirements for testing and qualification on the PV module level are defined in IEC 61730-1 (or IEC TS 62915 in case of retesting) and IEC 61215-1, with test methods provided by IEC 61730-2 and IEC 61215-2, respectively.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60904-2:2023(Main)
Photovoltaic devices - Part 2: Requirements for photovoltaic reference devices
SIST EN IEC 60904-2:2024

IEC 60904-2:2023 gives requirements for the classification, selection, packaging, marking, calibration and care of photovoltaic reference devices. This document applies to photovoltaic (PV) reference devices that are used to measure the irradiance of natural or simulated sunlight for the purpose of quantifying the electrical performance of photovoltaic devices (cells, modules and arrays). It does not cover photovoltaic reference devices for use under concentrated sunlight. This fourth edition cancels and replaces the third edition published in 2015. This edition includes the following significant technical changes with respect to the previous edition: a) added calibration procedures for calibrating PV devices at maximum power by extending the respective Clauses 12 and 13; b) revised requirements for mandatory measurement of spectral responsivity, temperature coefficients and linearity, depending on usage and allowing some measurements on equivalent devices; c) revised requirements for built-in shunt resistor; d) added requirements for traceability of calibration explicitly.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63027:2023(Main)
Photovoltaic power systems - DC arc detection and interruption
SIST EN IEC 63027:2023

IEC 63027:2023 applies to equipment used for the detection and optionally the interruption of electric DC arcs in photovoltaic (PV) system circuits. The document covers test procedures for the detection of series arcs within PV circuits, and the response times of equipment employed to interrupt the arcs. The document defines reference scenarios according to which the testing is conducted. This document covers equipment connected to systems not exceeding a maximum PV source circuit voltage of 1 500 V DC. This document provides requirements and testing procedures for arc-fault protection devices used in PV systems to reduce the risk of igniting an electrical fire.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60904-5:2011/A1:2022(Amendment)
Photovoltaic devices - Part 5: Determination of the equivalent cell temperature (ECT) of photovoltaic (PV) devices by the open-circuit voltage method
SIST EN 60904-5:2011/A1:2023

This part of IEC 60904 describes the preferred method for determining the equivalent cell
temperature (ECT) of PV devices (cells, modules and arrays of one type of module), for the
purposes of comparing their thermal characteristics, determining NOCT (nominal operating cell
temperature) or alternatively NMOT (nominal module operating temperature), and translating
measured I-V characteristics to other temperatures.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62109-3:2022(Main)
Safety of power converters for use in photovoltaic power systems - Part 3: Particular requirements for electronic devices in combination with photovoltaic elements
SIST EN IEC 62109-3:2023

IEC 62109-3:2020 covers the particular safety requirements for electronic elements that are mechanically and/or electrically incorporated with photovoltaic (PV) modules or systems. Mechanically and/or electrically incorporated means that the whole combination of electronic device with the photovoltaic element is sold as one product. Nevertheless, tests provided in this document may also be used to evaluate compatibility of PV modules and electronic devices that are sold separately and are intended to be installed close to each other. The purpose of the requirements of this document is to provide additional safety-related testing requirements for the following types of integrated electronics, collectively referred to as module integrated equipment (MIE): a) Type A MIE where the PV element can be evaluated as a PV module according to IEC 61730-1 and IEC 61730‑2 independently from the electronic element; b) Type B MIE where the PV element cannot be evaluated as a PV module according to IEC 61730-1 and IEC 61730-2 independently from the electronic element.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62759-1:2022(Main)
Photovoltaic (PV) modules - Transportation testing - Part 1: Transportation and shipping of module package units
SIST EN IEC 62759-1:2022

Photovoltaic (PV) modules are electrical devices intended for continuous outdoor exposure during their lifetime. Existing type approval standards do not consider mechanical stresses that may occur during transportation to the PV installation destination. This part of IEC 62759 describes methods for the simulation of transportation of complete package units of modules and combined subsequent environmental impacts. This standard is designed so that its test sequence can co-ordinate with those of IEC 61215 so that a single set of samples may be used to perform both the transportation simulation and performance evaluation of a photovoltaic module design.This standard applies to flat plate photovoltaic modules.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62108:2022(Main)
Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval
SIST EN IEC 62108:2022

This International Standard specifies the minimum requirements for the design qualification and type approval of concentrator photovoltaic (CPV) modules and assemblies suitable for long-term operation in general open-air climates as defined in IEC 60721-2-1. The test sequence is partially based on that specified in IEC 61215-1 for the design qualification and type approval of flat-plate terrestrial crystalline silicon PV modules. However, some changes have been made to account for the special features of CPV receivers and modules, particularly with regard to the separation of on-site and in-lab tests, effects of tracking alignment, high current density, and rapid temperature changes, which have resulted in the formulation of some new test procedures or new requirements. The object of this test standard is to determine the electrical, mechanical, and thermal characteristics of the CPV modules and assemblies and to show, as far as possible within reasonable constraints of cost and time, that the CPV modules and assemblies are capable of withstanding prolonged exposure in climates described in the scope. The actual life of CPV modules and assemblies so qualified will depend on their design, production, environment, and the conditions under which they are operated. This standard shall be used in conjunction with the retest guidelines described in Annex B.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61215-1-3:2021/A1:2022(Amendment)
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV) modules
SIST EN IEC 61215-1-3:2021/A1:2022
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61215-1-4:2021/A1:2022(Amendment)
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-4: Special requirements for testing of thin-film Cu(In,GA)(S,Se)2 based photovoltaic (PV) modules
SIST EN IEC 61215-1-4:2021/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61215-1-2:2021/A1:2022(Amendment)
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2: Special requirements for testing of thin-film Cadmium Telluride (CdTe) based photovoltaic (PV) modules
SIST EN IEC 61215-1-2:2021/A1:2022

No scope available

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day