EN 61784-5-14:2012

SLOVENSKI STANDARD
01-junij-2012
Industrijska komunikacijska omrežja - Profili - 5-14. del: Inštalacija procesnih vodil
- Inštalacijski profili za CPF 14 (IEC 61784-5-14:2010)
Industrial communication networks - Profiles - Part 5-14: Installation of fieldbuses -
Installation profiles for CPF 14 (IEC 61784-5-14:2010)
Industrielle Kommunikationsnetze - Profile - Teil 5-14: Feldbusinstallation -
Installationsprofile für die Kommunikationsprofilfamilie 14 (IEC 61784-5-14:2010)
Réseaux de communication industriels - Profils - Partie 5-14: Installation des bus de
terrain - Profils d'installation pour CPF 14 (CEI 61784-5-14:2010)
Ta slovenski standard je istoveten z: EN 61784-5-14:2012
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.100.05 9HþVORMQHXSRUDEQLãNH Multilayer applications
UHãLWYH
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61784-5-14
NORME EUROPÉENNE
April 2012
EUROPÄISCHE NORM
ICS 25.040.40; 35.100.40
English version
Industrial communication networks -
Profiles -
Part 5-14: Installation of fieldbuses -
Installation profiles for CPF 14
(IEC 61784-5-14:2010)
Réseaux de communication industriels -  Industrielle Kommunikationsnetze -
Profils - Profile -
Partie 5-14: Installation des bus de terrain - Teil 5-14: Feldbusinstallation -
Profils d'installation pour CPF 14 Installationsprofile für die
(CEI 61784-5-14:2010) Kommunikationsprofilfamilie 14
(IEC 61784-5-14:2010)
This European Standard was approved by CENELEC on 2011-10-19. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61784-5-14:2012 E
Foreword
The text of document 65C/602/FDIS, future edition 1 of IEC 61784-5-14, prepared by SC 65C, "Industrial
networks", of IEC/TC 65, "Industrial-process measurement, control and automation" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-14:2012.

The following dates are fixed:
(dop) 2012-10-20
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2014-10-19

standards conflicting with the
document have to be withdrawn
This standard is to be used in conjunction with IEC 61918, second edition (2010-07), together with the
European Common Modification published with EN 61918:2008.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61784-5-14:2010 was approved by CENELEC as a European
Standard without any modification.

- 3 - EN 61784-5-14:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61918 2010 Industrial communication networks - - -
Installation of communication networks in
industrial premises
IEC 61784-5-14 ®
Edition 1.0 2010-07
INTERNATIONAL
STANDARD
colour
inside
Industrial communication networks – Profiles –
Part 5-14: Installation of fieldbuses – Installation profiles for CPF 14
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
U
ICS 25.040.40; 35.100.40 ISBN 978-2-88912-060-4
– 2 – 61784-5-14 © IEC:2010(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
2 Normative references .7
3 Terms, definitions and abbreviated terms .7
4 CPF 14: Overview of installation profiles .7
5 Installation profile conventions .7
6 Conformance to installation profiles.8
Annex A (normative) CP 14/1 and 14/2 (EPA) specific installation profile.9

Figure 1 – Standards relationships.6
Figure A.1 – Example of EPA explosion-proof system.10
Figure A.2 – Earth of zener safety barrier .11
Figure A.3 – Earth of zener safety barrier .11
Figure A.4 – Example of power with Ethernet.14
Figure A.5 – Example of power supply over 0,2 A .15
Figure A.6 – Pin assignment of sub-D connector.24
Figure A.7 – Example of a 4-pin open style connector.25
Figure A.8 –Example of a 6-pin open style connector.26
Figure A.9 –– Example of an 8-pin open style connector.27

Table A.1 – Network characteristics for balanced cabling based on Ethernet .12
Table A.2 – Network characteristics for optical fibre cabling.13
Table A.3 – Information relevant to copper cable .15
Table A.4 –Information relevant to copper cable: fixed cables.16
Table A.5 – Information relevant to copper cable: cords.16
Table A.6 – Information relevant to optical fibre cables .17
Table A.7 – Connectors for balanced cabling CPs based on Ethernet .18
Table A.8 – Optical fibre connecting hardware .18
Table A.9 –Relationship between FOC and fibre types (CP 14/1 and CP 14/2) .19
Table A.10 – Specific connectors for balanced cabling based on Ethernet .19
Table A.11 Requirements of sub-D and open style connector .19
Table A.12 – Parameters for balanced cables .22
Table A.13 – Parameters for silica optical fibre cables .22
Table A.14 – Parameters for POF optical fibre cables .23
Table A.15 – Parameters for hard cladded silica optical fibre cables .23
Table A.16 – Signal lines assignment of sub-D connector .24
Table A.17 – Signal lines assignment of sub-D connector for 1 000 Base Ethernet .25
Table A.18 – Signal lines assignment for a 4-pin open style connector .26
Table A.19 – Signal lines assignment for a 6-pin open style connector .27

61784-5-14 © IEC:2010(E) – 3 –
Table A.20 – Signal lines assignment for an 8-pin open style connector(10/100 Mbit/s) .28
Table A.21 – Signal lines assignment for an 8-pin open style connector(1 000 Mbit/s) .28

– 4 – 61784-5-14 © IEC:2010(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –
Part 5-14: Installation of fieldbuses –
Installation profiles for CPF 14

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61784-5-14 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This standard is to be used in conjunction with IEC 61918:2010.

61784-5-14 © IEC:2010(E) – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
65C/602/FDIS 65C/616/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordanc
...