EN IEC 60695-2-13:2021
(Main)Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials
Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials
This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT). The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test temperature, determined during this standardized procedure, at which the tested material does not ignite, or sustained flaming combustion does not occur for a time longer than 5 s for any single flame event and the specimen is not totally consumed. This test is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire flammability index (GWFI) test method for materials, IEC 60695-2-12, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests can allow a reduction of end product testing. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-13: Prüfverfahren mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entzündbarkeit (GWIT) von Werkstoffen
Essais relatifs aux risques du feu - Partie 2-13: Essais au fil incandescent/chauffant - Méthode d'essai de température d'allumage au fil incandescent (GWIT) pour matériaux
IEC 60695-2-13:2021 est disponible sous forme de IEC 60695-2-13:2021 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 60695-2-13:2021 décrit l’essai au fil incandescent applicable à des éprouvettes d’essai de matériaux isolants électriques solides ou autres matériaux solides pour les essais d’allumage dans le but de déterminer la température d'allumage au fil incandescent (GWIT, glow-wire ignition temperature). La GWIT est la température qui est supérieure de 25 K (ou 30 K) à la température d'essai maximale, déterminée durant cette procédure normalisée, à laquelle le matériau soumis à l’essai ne s’enflamme pas, ou une combustion avec flamme persistante ne se produit pas pendant une durée supérieure à 5 s pour un événement d’inflammation unique quelconque et l'éprouvette d’essai n'est pas entièrement consumée. Cet essai est un essai de matériaux exécuté sur une série d’éprouvettes d’essai normalisées. Les données obtenues, ainsi que les données issues de la méthode d’essai d'indice d'inflammabilité au fil incandescent (GWFI, glow-wire flammability index) pour matériaux, IEC 60695-2-12, peuvent alors être utilisées dans un processus de présélection conformément à l’IEC 60695-1-30 [4] pour estimer l'aptitude des matériaux à satisfaire aux exigences de l’IEC 60695 2 11. La présente publication fondamentale de sécurité, fondée sur la ou les méthodes d'essai de sécurité, est essentiellement destinée à être utilisée par les comités d’études dans le cadre de l’élaboration de publications de sécurité conformément aux principes établis dans le Guide IEC 104 et le Guide ISO/IEC 51. L’une des responsabilités d’un comité d’études consiste, le cas échéant, à utiliser les publications fondamentales de sécurité dans le cadre de l’élaboration de ses publications. Cette norme doit être utilisée conjointement avec l’IEC 60695-2-10. Cette troisième édition annule et remplace la deuxième édition parue en 2010 et l'Amendement 1:2014. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - Ajout à l’Article 3 de nouveaux termes et définitions, ayant rapport aux moments et durées, applicables à la méthode d'essai.
Preskušanje požarne ogroženosti - 2-13. del: Preskusne metode z žarilno žico - Preskusna metoda za materiale: temperatura vžiga žareče žice (GWIT) (IEC 60695-2-13:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 60695-2-13:2011
SIST EN 60695-2-13:2011/A1:2014
Preskušanje požarne ogroženosti - 2-13. del: Preskusne metode z žarilno žico -
Preskusna metoda za materiale: temperatura vžiga žareče žice (GWIT) (IEC 60695-
2-13:2021)
Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition
temperature (GWIT) test method for materials (IEC 60695-2-13:2021)
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-13: Prüfverfahren mit dem Glühdraht
- Prüfung mit dem Glühdrat zur Entzündbarkeit (GWIT) von Werkstoffen (IEC 60695-2-
13:2021)
Essais relatifs aux risques du feu - Partie 2-13: Essais au fil incandescent/chauffant -
Méthode d'essai de température d'allumage au fil incandescent (GWIT) pour matériaux
(IEC 60695-2-13:2021)
Ta slovenski standard je istoveten z: EN IEC 60695-2-13:2021
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60695-2-13
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2021
ICS 13.220.40; 29.020 Supersedes EN 60695-2-13:2010 and all of its
amendments and corrigenda (if any)
English Version
Fire hazard testing - Part 2-13: Glowing/hot-wire based test
methods - Glow-wire ignition temperature (GWIT) test method
for materials
(IEC 60695-2-13:2021)
Essais relatifs aux risques du feu - Partie 2-13: Essais au fil Prüfungen zur Beurteilung der Brandgefahr - Teil 2-13:
incandescent/chauffant - Méthode d'essai de température Prüfverfahren mit dem Glühdraht - Prüfung mit dem
d'allumage au fil incandescent (GWIT) pour matériaux Glühdrat zur Entzündbarkeit (GWIT) von Werkstoffen
(IEC 60695-2-13:2021) (IEC 60695-2-13:2021)
This European Standard was approved by CENELEC on 2021-09-28. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60695-2-13:2021 E
European foreword
The text of document 89/1538/FDIS, future edition 3 of IEC 60695-2-13, prepared by IEC/TC 89 "Fire
hazard testing" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-06-28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-09-28
document have to be withdrawn
This document supersedes EN 60695-2-13:2010 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60695-2-13:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60695-1-10 NOTE Harmonized as EN 60695-1-10
IEC 60695-1-11 NOTE Harmonized as EN 60695-1-11
IEC 60695-2-11 NOTE Harmonized as EN 60695-2-11
IEC 60695-1-30 NOTE Harmonized as EN 60695-1-30
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60695-2-10 - Fire hazard testing - Part 2-10: EN 60695-2-10 -
Glowing/hot-wire based test methods -
Glow-wire apparatus and common test
procedure
IEC 60695-2-12 - Fire hazard testing - Part 2-12: EN 60695-2-12 -
Glowing/hot-wire based test methods -
Glow-wire flammability index (GWFI) test
method for materials
IEC 60695-4 2021 Fire hazard testing - Part 4: Terminology EN IEC 60695-4 2021
concerning fire tests for electrotechnical
products
ISO 291 2008 Plastics - Standard atmospheres for EN ISO 291 2008
conditioning and testing
ISO 293 - Plastics – Compression moulding of test - -
specimens of thermoplastic materials
ISO 294 series Plastics – Injection moulding of test EN ISO 294 series
specimens of thermoplastic materials
ISO 295 - Plastics - Compression moulding of test EN ISO 295 -
specimens of thermosetting materials
ISO 13943 2017 Fire safety – Vocabulary EN ISO 13943 2017
IEC 60695-2-13 ®
Edition 3.0 2021-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
HORIZONTAL PUBLICATION
PUBLICATION HORIZONTALE
Fire hazard testing –
Part 2-13: Glowing/hot-wire based test methods – Glow-wire ignition
temperature (GWIT) test method for materials
Essais relatifs aux risques du feu –
Partie 2-13: Essais au fil incandescent/chauffant – Méthode d’essai de
température d’allumage au fil incandescent (GWIT) pour matériaux
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40; 29.020 ISBN 978-2-8322-1011-2
– 2 – IEC 60695-2-13:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references. 6
3 Terms and definitions . 7
4 Test specimens . 8
4.1 Test specimen preparation . 8
4.2 Test specimen dimensions . 8
4.3 Testing ranges in formulations . 9
4.3.1 General . 9
4.3.2 Density, melt flow, and filler/reinforcement . 9
4.3.3 Colour . 9
5 Apparatus . 9
6 Temperature measuring system verification . 9
7 Conditioning and test conditions . 9
7.1 Conditioning of test specimens . 9
7.2 Testing conditions . 10
8 Test procedure . 10
8.1 General . 10
8.2 Initial test temperatures . 10
8.3 Test temperatures . 10
9 Observations and measurements . 11
9.1 Initial observations . 11
9.2 Test observations . 11
10 Evaluation of test results . 11
10.1 Test criteria . 11
10.2 Glow-wire ignition temperature . 11
11 Test report. 12
Bibliography . 13
Table 1 – Initial test temperatures . 10
IEC 60695-2-13:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 2-13: Glowing/hot-wire based test methods –
Glow-wire ignition temperature (GWIT) test method for materials
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its direc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.