EN ISO 294-2:1998

SLOVENSKI STANDARD
SIST EN ISO 294-2:2000
01-maj-2000
3ROLPHUQLPDWHULDOL9EUL]JDYDQMHSODVWRPHUQLKSUHVNXãDQFHYGHO0DOL
SDOLþDVWLSUHVNXãDQFL,62
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small
tensile bars (ISO 294-2:1996)
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 2: Kleine
Zugstäbe (ISO 294-2:1996)
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques -
Partie 2: Barreaux de traction de petites dimensions (ISO 294-2:1996)
Ta slovenski standard je istoveten z: EN ISO 294-2:1998
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 294-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 294-2:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 294-2:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 294-2:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 294-2:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 294-2:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 294-2:2000
INTERNATIONAL
STANDARD
First edition
1996-l 2-l 5
- Injection moulding of test
Plastics
specimens of thermoplastic materials -
Part 2:
Small tensile bars
- Moulage par injection des Gprouvettes de matbiaux
P/as tiques
thermoplastiques -
Partie 2: Barreaux de traction de petites dimensions
Reference number
IS0 294-2:1996(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 294-2:2000
IS0 294-2: 1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 294-2 was prepared by Technical Committee
ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
Together with the other parts, this part of IS0 294 cancels and replaces
the second edition of IS0 294 (IS0 294:1995) which has been revised to
improve the definition of the injection-moulding parameters and has been
restructured to specify four types of IS0 mould for the production of the
basic specimen types required for the acquisition of comparable test data.
Care has been taken to ensure that the IS0 moulds described can all be
fitted in existing injection-moulding equipment and have interchangeable
cavity plates.
IS0 294 consists of the following parts, under the general title Plastics -
Injection mouldlng of test specimens of thermoplastic materials:
- Part 7: General principles, and moulding of multipurpose and bar test
specimens
- Part 2: Small tensile bars
-
Part 3: Small plates
Part 4: Determination of moulding shrinkage
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be
reproduced or utilized in any form or by any means, electronic or mechanical, including
photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland

---------------------- Page: 8 ----------------------

SIST EN ISO 294-2:2000
IS0 294-2: 1996(E)
INTERNATIONAL STANDARD @ IS0
Plastics - Injection moulding of test specimens of thermoplastic
materials -
Part 2:
Small tensile bars
1 Scope
This part of IS0 294 specifies a four-cavity mould, the type C IS0 mould, for the injection moulding of small tensile
> 60 mm x 10 mm x 3 mm (the type 4 test specimen in IS0 8256:1990).
bars measuring
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part
of IS0 294. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of IS0 294 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently
valid International Standards.
I SO 294-l : 1996, P/as tics - In
...