iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60519-11:1997

(Main)

Safety in electroheat installations - Part 11: Particular requirements for installations for electromagnetic stirring, transport or pouring of metal liquids

Safety in electroheat installations - Part 11: Particular requirements for installations for electromagnetic stirring, transport or pouring of metal liquids

Applies to systems such as: Stirring devices for continuous machines, adjoining or being part of arc furnaces, ladles, etc; transport of liquid metal for emptying or filling furnaces, launders or moulds; devices to transport liquid metal with simultaneous proportioning of the transported quantity, e.g. for filling diecasting machines; systems for influencing the ingot surface or the pouring stream enhancing crystallization by means of an electromagnetic field during continuous casting. Shall be read in conjunction with EN 60519-1

Sicherheit in Elektrowärmeanlagen - Teil 11: Besondere Anforderungen für Anlagen zum elektromagnetischen Rühren, Fördern und Gießen flüssiger Metalle

Sécurité dans les installations électrothermiques - Partie 11: Règles particulières pour les installations pour brassage, transport ou coulée électromagnétique des métaux liquides

S'applique aux systèmes tels que: dispositifs de brassage pour machines à coulée continue adjacentes à des fours à arc ou faisant partie de celles-ci; Transport de métal liquide pour remplir ou vider des fours ou des moules; Dispositifs de transport pour le métal liquide avec répartition simultanée des quantités transportées, par exemple pour le remplissage de machines de coulée;Systèmes pour influencer la surface du lingot ou le jet de coulée au moyen d'un champ électromagnétique lors de la coulée continue en vue de favoriser la cristallisation. Doit être lue conjointement avec la norme EN 60519-1

Varnost pri električnih grelnih inštalacijah - 11. del: Posebne zahteve za inštalacije za elektromagnetno mešanje, prevoz ali pretakanje tekočih kovin (IEC 60519-11:1997)

General Information

Status
Withdrawn
Publication Date
28-May-1997
Withdrawal Date
31-Jan-1998
ICS
25.180.10 - Electric furnaces
Technical Committee
CLC/SR 27 - Industrial electroheating equipment
Drafting Committee
IEC/TC 27 - IEC_TC_27
Parallel Committee
IEC/TC 27 - IEC_TC_27
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Sep-2010
Completion Date
01-Sep-2010
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
SIST EN 60519-11:1999 - Safety in electroheat installations - Part 11: Particular requirements for installations for electromagnetic stirring, transport or pouring of metal liquids

Relations

Replaced By
EN 60519-11:2007 - Safety in electroheat installations - Part 11: Particular requirements for installations using the effect of electromagnetic forces on liquid metals
Effective Date
28-Jan-2023

Buy Standard

EN 60519-11:1999EN 60519-11:1999
PreviousNext
Standard
EN 60519-11:1999
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-1999
9DUQRVWSULHOHNWULþQLKJUHOQLKLQãWDODFLMDKGHO3RVHEQH]DKWHYH]DLQãWDODFLMH
]DHOHNWURPDJQHWQRPHãDQMHSUHYR]DOLSUHWDNDQMHWHNRþLKNRYLQ ,(&

Safety in electroheat installations - Part 11: Particular requirements for installations for
electromagnetic stirring, transport or pouring of metal liquids
Sicherheit in Elektrowärmeanlagen - Teil 11: Besondere Anforderungen für Anlagen zum
elektromagnetischen Rühren, Förder
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60519-6:2024(Main)
Safety in installations for electroheating and electromagnetic processing - Part 6: Particular requirements for high frequency dielectric and microwave heating and processing equipment
SIST EN IEC 60519-6:2024

This part of IEC 60519 is applicable to equipment using high frequency or microwave energy alone or in combination with other kinds of energy for industrial heating and processing of materials. It is also applicable to HF and MW generators made available to users as separate units. This part is applicable to equipment operating in the frequency range 3 MHz to 300 GHz, with the following limitations. - This document applies to only high frequency dielectric heating and processing as defined in 3.1.103. It does not apply to induction heating, which it is possible to carry out in the lower part of the specified frequency band and is covered by IEC 60519-3, with magnetic field safety aspects addressed in IEC TS 62997:2017, the latter to be replaced by a technical report (TR) or by a revised technical specification (TS). - The ISM centre frequencies for dielectric heating and processing of industrial interest are narrow bands about 6,78 MHz, 13,56 MHz, 27,12 MHz and 40,68 MHz. Different field emission measurement procedures and limiting values are applicable, depending on the processing frequency in the high frequency range 3 to 300 MHz. Specifications are in Annex BB. - This document specifies limits for microwave emission only for the ISM frequencies between 800 MHz and 6 MHz, as specified in Annex CC. For other microwave frequencies the basic restriction and IEC 62311 apply. - The foundations for compliance with emission values are the basic restrictions, referred to in the IEEE/ANSI C95.1:2019 and Directive 2013/35/EU. However, maximum HF processing frequency electric and magnetic field values are taken from the IEEE/ANSI C95.1:2019 standard, as indicated in Annex BB. - This document is not applicable to: -- appliances for household and similar use (covered by e.g. IEC 60335-2-25); -- commercial use (covered by IEC 60335-2-90 and IEC 60335-2-110); -- laboratory use (covered by IEC 61010-2-010); -- medical high frequency equipment and accessories (covered by IEC 60601-2-2). NOTE 101 Since high frequency and microwave tunnel ovens and also some other types of microwave and high frequency equipment are sometimes intended either for commercial, laboratory or industrial use, the following criteria are suitable for determination of the classification as industrial equipment: - commercial equipment is typically designed and planned for series production of many identical units, whereas industrial equipment is typically produced in small series or even as single units. The processed goods are consumed or ready for final use at the end of the heating process. - laboratory heating equipment is for preparing material in a laboratory environment, and the processed material is immediately available for investigations or further processing. Regular production of large quantities of material is not foreseen. - with industrial equipment, the processed goods are not immediately accessible to the end user, and the goods are sometimes not in a final state from the perspective of the end user.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60676:2024(Main)
Industrial electroheating equipment - Test methods for direct arc furnaces
SIST EN IEC 60676:2024

IEC 60676:2024 This document specifies the basic test procedures, conditions and methods for establishing the main performance parameters and the main operational characteristics of furnaces for direct arc heating, forming arcs between the electrode and metal, such as electric arc furnaces using alternating current (EAF AC) or direct current (EAF DC), and ladle furnaces (LF), with rated power level above 500 kVA . This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The structure has been redrafted according to IEC 60398:2015. b) The scope has been redrafted. c) The terms/definitions, normative references and bibliography have been updated and completed. d) The test methods and content from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF). e) The annexes from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF).

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60519-4:2022(Main)
Safety in installations for electroheating and electromagnetic processing - Part 4: Particular requirements for arc furnace installations
SIST EN IEC 60519-4:2022

This part of IEC 60519 provides particular safety requirements for arc furnace installations. This document deals with the significant hazards, hazardous situations or hazardous events relevant to industrial arc furnace installations, as listed in Annex A, for normal operation and for single fault condition as well as under conditions of reasonably foreseeable misuse. This document specifies the requirements intended to be met by the manufacturer to ensure the safety of persons and property during the complete life cycle of the equipment from design through commissioning, operation, maintenance, inspection, to decommissioning, as well as in the event of foreseeable single fault condition that can occur in the equipment. The rated voltage of arc furnace installation can be in the range of low voltage or high voltage, details are given in 4.2. This standard is applicable to arc furnace installations such as: a) furnaces for direct arc heating, forming arcs between the electrode and metal such as the electric arc furnace using alternating current (EAF AC) or direct current (EAF DC), and the ladle furnace (LF); b) furnaces for arc-resistance heating forming arcs between the electrode and the charge material or heating the charge material by the Joule effect, such as the submerged arc resistance furnace using alternating current (SAF AC), or direct current (SAF DC). NOTE In some documents the terms smelter or electrical reduction furnace are used. Furnace installation for unattended operation is not covered by this standard. This document does not provide requirements for type testing. NOTE Industrial equipment covered by this document is typically produced as a single unit or a very small number of units; such unit usually has a very high value and can cause severe harm at disintegration. This document does not address data security and hazards arising from neglect of security. With respect to noise of electrical an arc furnace, ISO 13578:2017, 6.1.23 applies.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60779:2020(Main)
Installations for electroheating and electromagnetic processing - Test methods for electroslag remelting furnaces
SIST EN IEC 60779:2020

IEC 60779:2020 specifies the test procedures, conditions and methods for determining the main performance parameters and operational characteristics of electroslag remelting furnaces. Measurements and tests that are solely used for the verification of safety requirements of the installations are outside the scope of this document and are covered by IEC 60519-1 and IEC 60519-8. This third edition cancels and replaces the second edition published in 2005. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the structure has been redrafted according to IEC 60398:2015; - the scope and object have been redrafted; - the terms/definitions, normative references and bibliography have been updated and completed; - all test methods and content from IEC 60779:2005 that have been included in IEC 60398:2015 have been removed to avoid any duplication.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60519-8:2020(Main)
Safety in installations for electroheating and electromagnetic processing - Part 8: Particular requirements for electroslag remelting furnaces
SIST EN IEC 60519-8:2020

IEC 60519-8:2020 specifies particular safety requirements for electroslag remelting equipment and installations. This document specifies safety requirements applicable to mainly electroheating installations for remelting and, in some cases, for refining processes of metals through direct resistance heating of a conductive slag. The object of this document is to specify the particular requirements for the safety of persons in or around an electroslag remelting furnace. The general requirements are included in IEC 60519-1. This third edition cancels and replaces the second edition published in 2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the structure has been redrafted according to IEC 60519-1:2020; b) the Scope has been redrafted; c) the terms and definitions, normative references and bibliography have been updated and completed; d) all requirements and content from IEC 60519-8:2005 that have been included in IEC 60519‑1:2020 have been removed to avoid any duplication.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60519-1:2020(Main)
Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements
SIST EN IEC 60519-1:2020

IEC 60519-1:2020 is available as IEC 60519-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60519-1:2020 specifies the general safety requirements for industrial installations or equipment intended for electroheating (EH) and electroheating based treatment technologies as well as for electromagnetic processing of materials (EPM). This document deals with the significant hazards, hazardous situations or hazardous events relevant to industrial EH and EPM equipment, as listed in Annex A, for normal operation and for single fault condition as well as under conditions of reasonably foreseeable misuse. This sixth edition cancels and replaces the fifth edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - removal of noise from the scope; - clarification of EMC requirements; - risk classification of hazards based on emission for all processing frequencies; - clarification of boundaries between IEC 60519 (all parts) and ISO 13577 (all parts).

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63078:2020(Main)
Installations for electroheating and electromagnetic processing - Test methods for induction through-heating installations
SIST EN IEC 63078:2020

IEC 63078:2019 specifies the test procedures, conditions and methods for determining the main performance parameters and operational characteristics of induction through-heating installations. Measurements and tests that are solely used for the verification of safety requirements of the installations are outside the scope of this document and are covered by IEC 60519-1 and IEC 60519-3.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60519-12:2018(Main)
Safety in installations for electroheating and electromagnetic processing - Part 12: Particular requirements for infrared electroheating
SIST EN IEC 60519-12:2018

IEC 60519-12:2016 specifies safety requirements for industrial electroheating equipment and installations in which infrared radiation – usually generated by infrared emitters – is significantly dominating over heat convection or heat conduction as means of energy transfer to the workload. A further limitation of the scope is that the infrared emitters have a maximum spectral emission at longer wavelengths than 780 nm in air or vacuum, and are emitting wideband continuous spectra such as by thermal radiation or high pressure arcs. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a. the structure has been redrafted according to IEC 60519-1:2015; b. terms/definitions, normative references and bibliography have been updated and completed; c. all requirements and content from IEC 60519-12:2013 that have been included in IEC 60519-1:2015 have been removed to avoid any duplication.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60398:2015(Main)
Installations for electroheating and electromagnetic processing - General performance test methods
SIST EN 60398:2015

IEC 60398:2015 specifies the basic test procedures, conditions and methods for establishing the main performance parameters and the main operational characteristics of industrial installations and equipment intended for electroheating (EH) or electromagnetic processing of materials (EPM). This third edition cancels and replaces the second edition of IEC 60398 published in 1999 and the first edition of IEC TS 62796 published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the title and scope of the standard have been expanded to include installations and equipment for electromagnetic processing of materials; - the requirements have been restructured; - tests concerning safety have been moved to IEC 60519-1; - new tests and clauses addressing energy efficiency considerations have been added; - a new annex placing this standard in the context of energy efficiency assessment as developed by ISO and IEC has been added; - new annexes addressing visual display of data, estimation of energy use and energy recoverability of fluids have been added.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62798:2014/AC:2014(Corrigendum)
Industrial electroheating equipment - Test methods for infrared emitters
SIST EN 62798:2015/AC:2015
  • Corrigendum
    1 page
    English and French language
    sale 10% off
    e-Library read for
    1 day