EN IEC 60519-4:2022
(Main)Safety in installations for electroheating and electromagnetic processing - Part 4: Particular requirements for arc furnace installations
Safety in installations for electroheating and electromagnetic processing - Part 4: Particular requirements for arc furnace installations
This part of IEC 60519 provides particular safety requirements for arc furnace installations. This document deals with the significant hazards, hazardous situations or hazardous events relevant to industrial arc furnace installations, as listed in Annex A, for normal operation and for single fault condition as well as under conditions of reasonably foreseeable misuse. This document specifies the requirements intended to be met by the manufacturer to ensure the safety of persons and property during the complete life cycle of the equipment from design through commissioning, operation, maintenance, inspection, to decommissioning, as well as in the event of foreseeable single fault condition that can occur in the equipment. The rated voltage of arc furnace installation can be in the range of low voltage or high voltage, details are given in 4.2. This standard is applicable to arc furnace installations such as: a) furnaces for direct arc heating, forming arcs between the electrode and metal such as the electric arc furnace using alternating current (EAF AC) or direct current (EAF DC), and the ladle furnace (LF); b) furnaces for arc-resistance heating forming arcs between the electrode and the charge material or heating the charge material by the Joule effect, such as the submerged arc resistance furnace using alternating current (SAF AC), or direct current (SAF DC). NOTE In some documents the terms smelter or electrical reduction furnace are used. Furnace installation for unattended operation is not covered by this standard. This document does not provide requirements for type testing. NOTE Industrial equipment covered by this document is typically produced as a single unit or a very small number of units; such unit usually has a very high value and can cause severe harm at disintegration. This document does not address data security and hazards arising from neglect of security. With respect to noise of electrical an arc furnace, ISO 13578:2017, 6.1.23 applies.
Sicherheit in Elektrowärmeanlagen und Anlagen für elektromagnetische Bearbeitungsprozesse - Teil 4: Besondere Bestimmungen für Lichtbogenofenanlagen
Sécurité dans les installations destinées au traitement électrothermique et électromagnétique - Partie 4: Exigences particulières pour les installations de fours à arc
L'IEC 60519-4:2021 fournit des exigences de sécurité particulières pour les installations de fours à arc. Le présent document traite des dangers significatifs, des situations dangereuses ou des événements dangereux liés aux installations industrielles de fours à arc, répertoriés à l'Annexe A, en fonctionnement normal et en condition de premier défaut, ainsi qu'en cas de mauvais usage raisonnablement prévisible. Cette cinquième édition annule et remplace la quatrième édition parue en 2013. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
la structure a été remaniée sur la base de l'IEC 60519-1:2020;
le domaine d'application et l'objet ont été reformulés;
les termes et définitions, les références normatives et la bibliographie ont été mis à jour et complétés;
les exigences ont été remaniées sur la base de l'IEC 60519-1:2020;
toutes les dispositions ont été reformulées et le texte relatif aux installations de fours à arc submergé est plus concis;
les annexes ont été restructurées, en ce qui concerne les détails relatifs aux conceptions haute tension et aux problèmes non électriques, mais dont il faut tenir compte dans le cadre de ces installations;
l'aspect relatif au bruit a été retiré du domaine d'application;
les exigences de CEM ont été clarifiées;
la classification des risques et des dangers a été établie en fonction des émissions;
les limites ont été clarifiées selon l'ISO 13577 (toutes les parties) et l'ISO 13578.
Varnost pri električnih grelnih inštalacijah in elektromagnetni obdelavi - 4. del: Posebne zahteve za inštalacije obločnih peči (IEC 60519-4:2021)
Ta del standarda IEC 60519 podaja posebne varnostne zahteve za inštalacije obločnih peči. Ta dokument opisuje vsa večja tveganja, nevarne situacije ali dogodke v zvezi z inštalacijami industrijskih obločnih peči, kot je navedeno v dodatku A, pri običajnem obratovanju in v razmerah posamične okvare ter pod pogoji razumno predvidljive nepravilne uporabe. Ta dokument določa zahteve, ki naj bi jih izpolnjeval proizvajalec za zagotovitev varnosti oseb in premoženja v celotnem življenjskem ciklu opreme od načrtovanja in začetka obratovanja, obratovanja, vzdrževanja, pregleda do prenehanja obratovanja ter v primeru predvidljivih razmer posamične okvare, do katerih lahko pride pri opremi. Nazivna napetost inštalacije obločnih peči je lahko v razponu nizke ali visoke napetosti (podrobnosti so podane v točki 4.2). Ta standard se uporablja za inštalacije obločnih peči, kot so: a) peči za neposredno obločno gretje, ki tvorijo obloke med elektrodo in kovino, npr. električna obločna peč, ki uporablja izmenični tok (EAF AC) ali enosmerni tok (EAF DC), in ponovčna peč (LF); b) peči za obločno uporovno gretje, ki tvorijo obloke med elektrodo in materialom naboja ali segrevajo material naboja z Joulovim učinkom, npr. obločna uporovna peč z zakritim oblokom, ki uporablja izmenični tok (SAF AC) ali enosmerni tok (SAF DC). OPOMBA 1: V nekaterih dokumentih se uporablja izraz »talilnica« ali »električna redukcijska peč«. Inštalacija peči za nenadzorovano obratovanje v tem dokumentu ni zajeta. Ta dokument ne podaja zahtev za tipsko preskušanje. OPOMBA 2: Industrijska oprema, ki jo zajema ta dokument, je običajno proizvedena kot samostojna enota ali kot zelo majhno število enot. Takšna enota ima običajno zelo visoko vrednost in lahko pri razpadu povzroči resno škodo. Ta dokument ne obravnava varnosti podatkov in tveganj, povezanih z zanemarjanjem varnosti. V zvezi s hrupom električne obločne peči se uporablja standard ISO 13578:2017, točka 6.1.23. Električna obločna peč, ki uporablja enosmerni tok, in obločna uporovna peč z zakritim oblokom, ki uporablja enosmerni tok, sta razvrščeni kot vrsta opreme z ničelno frekvenco (0 Hz). Električna obločna peč, ki uporablja izmenični tok, obločna uporovna peč z zakritim oblokom, ki uporablja izmenični tok, in ponovčna peč so razvrščene kot vrsta opreme z omrežno frekvenco (50 ali 60 Hz). Peči, ki obratujejo pri frekvencah zunaj razpona zgoraj navedenih vrst opreme, v tem dokumentu niso zajete.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2022
Nadomešča:
SIST EN 60519-4:2014
Varnost pri električnih grelnih inštalacijah in elektromagnetni obdelavi - 4. del:
Posebne zahteve za inštalacije obločnih peči (IEC 60519-4:2021)
Safety in installations for electroheating and electromagnetic processing - Part 4:
Particular requirements for arc furnace installations (IEC 60519-4:2021)
Sicherheit in Elektrowärmeanlagen und Anlagen für elektromagnetische
Bearbeitungsprozesse - Teil 4: Besondere Bestimmungen für Lichtbogenofenanlagen
(IEC 60519-4:2021)
Sécurité dans les installations destinées au traitement électrothermique et
électromagnétique - Partie 4: Exigences particulières pour les installations de fours à arc
(IEC 60519-4:2021)
Ta slovenski standard je istoveten z: EN IEC 60519-4:2022
ICS:
25.180.10 Električne peči Electric furnaces
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60519-4
NORME EUROPÉENNE
EUROPÄISCHE NORM February 2022
ICS 25.180.10 Supersedes EN 60519-4:2013 and all of its amendments
and corrigenda (if any)
English Version
Safety in installations for electroheating and electromagnetic
processing - Part 4: Particular requirements for arc furnace
installations
(IEC 60519-4:2021)
Sécurité dans les installations destinées au traitement Sicherheit in Elektrowärmeanlagen und Anlagen für
électrothermique et électromagnétique - Partie 4: Exigences elektromagnetische Bearbeitungsprozesse - Teil 4:
particulières pour les installations de fours à arc Besondere Bestimmungen für Lichtbogenofenanlagen
(IEC 60519-4:2021) (IEC 60519-4:2021)
This European Standard was approved by CENELEC on 2022-01-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60519-4:2022 E
European foreword
The text of document 27/1141/FDIS, future edition 5 of IEC 60519-4, prepared by IEC/TC 27
“Industrial electroheating and electromagnetic processing” was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 60519-4:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–10–19
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025–01–19
document have to be withdrawn
This document supersedes EN 60519-4:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN IEC 60519-1.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60519-4:2021 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60076 (series) NOTE Harmonized as EN 60076 (series)
IEC 60146-1 (series) NOTE Harmonized as EN 60146-1 (series)
IEC 60676:2011 NOTE Harmonized as EN 60676:2012 (not modified)
IEC 60683:2011 NOTE Harmonized as EN 60683:2012 (not modified)
IEC 61378 (series) NOTE Harmonized as EN 61378 (series)
IEC 62477-2 NOTE Harmonized as EN IEC 62477-2
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
The Annex ZA of Part 1 is applicable except as follows:
Publication Year Title EN/HD Year
Replacement:
IEC 61936-1 2021 Power installations exceeding 1 kV AC and EN IEC 61936-1 2021
1,5 kV DC - Part 1: AC
Additions:
IEC 60060-3 - High voltage test techniques - Part 3: EN 60060-3 -
Definitions and requirements for on-site
testing
IEC 60519-1 2020 Safety in installations for electroheating EN IEC 60519-1 2020
and electromagnetic processing - Part 1:
General requirements
ISO 13577-1 2016 Industrial furnaces and associated - -
processing equipment - Safety - Part 1:
General requirements
ISO 13578 2017 Industrial furnaces and associated - -
processing equipment - Safety
requirements for machinery and equipment
for production of steel by electric arc
furnaces
IEC 60519-4 ®
Edition 5.0 2021-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Safety in installations for electroheating and electromagnetic processing –
Part 4: Particular requirements for arc furnace installations
Sécurité dans les installations destinées au traitement électrothermique et
électromagnétique –
Partie 4: Exigences particulières pour les installations de fours à arc
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.180.10 ISBN 978-2-8322-1059-1
– 2 – IEC 60519-4:2021 © IEC 2021
CONTENTS
FOREWORD . 6
INTRODUCTION . 9
1 Scope . 10
2 Normative references . 10
3 Terms, definitions and abbreviated terms . 11
3.1 General concepts . 11
3.2 Equipment and state of equipment . 11
3.3 Parts and accessories . 14
3.4 Safety related concepts . 14
3.5 Abbreviated terms . 14
4 Classification and subdivision of equipment and installations . 14
4.1 Classification by processing frequency. 14
4.2 Classification by voltage . 14
4.3 Subdivision of installation and equipment . 14
4.4 Classification of hazards and risks . 14
5 Risk assessment . 15
6 General provisions. 15
6.1 Basic considerations . 15
6.2 Significant hazards . 15
6.3 Physical environment and operating conditions for the installation as such
and electrical equipment outside the processing equipment . 15
6.4 Physical environment and operating conditions for electrical equipment
caused by operation of the processing equipment . 16
6.5 Power supply . 16
6.6 Access . 17
6.7 Ergonomic aspects . 17
6.8 Transport and storage . 17
6.9 Provisions for handling. 17
6.10 Consumables and replaceable parts . 18
7 Protection against hazards from electric shock . 18
7.1 General . 18
7.2 Fundamental rule of protection . 18
7.3 General provisions . 18
7.4 Basic protection . 19
7.5 Provisions for protection in electric single fault condition . 19
7.6 Protective equipotential bonding . 19
7.7 Additional provisions for fault protection for frequencies above 200 Hz . 20
7.8 Currents in protective conductors . 20
7.9 Touch current and touch voltage . 20
7.10 Conductors and insulations at high temperature . 20
7.11 Non-electric faults . 20
8 Protection against hazards from electric or magnetic fields . 20
8.1 General . 20
8.2 Magnetic fields . 21
8.3 Magnetic fields below 1 Hz . 21
8.4 Local electric fields . 21
IEC 60519-4:2021 © IEC 2021 – 3 –
8.5 Requirements related to barriers and screens . 21
8.6 Requirements related to objects worn, carried or held by persons . 21
9 Protection against hazards from radiation . 21
9.1 General . 21
9.2 Installation or equipment generating ionizing radiation . 21
9.3 Ultraviolet radiation . 21
9.4 Visible and infrared radiation . 21
9.5 Laser sources . 22
10 Protection against hazards from thermal influences . 22
10.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.