25.180 - Industrial furnaces

This International Standard specifies the test procedures, conditions and methods for
determining the main performance parameters and operational characteristics of electroslag
remelting furnaces.
Measurements and tests that are solely used for the verification of safety requirements of the
installations are outside the scope of this document and are covered by IEC 60519-1 and
IEC 60519-8.
This document applies to industrial electroslag remelting furnaces, the rated capacity of which
is e...view more

This part of IEC 60519 specifies particular safety requirements for electroslag remelting
equipment and installations.
This document specifies safety requirements applicable to mainly electroheating installations
for remelting and, in some cases, for refining processes of metals through direct resistance
heating of a conductive slag.
The object of this document is to specify the particular requirements for the safety of persons
in or around an electroslag remelting furnace. The general req...view more

IEC 60779:2020 specifies the test procedures, conditions and methods for determining the main performance parameters and operational characteristics of electroslag remelting furnaces.
Measurements and tests that are solely used for the verification of safety requirements of the installations are outside the scope of this document and are covered by IEC 60519-1 and IEC 60519-8.
This third edition cancels and replaces the second edition published in 2005. It constitutes a technical revision.
Th...view more

This part of IEC 60519 specifies the general safety requirements for industrial installations or
equipment intended for electroheating (EH) and electroheating based treatment
technologies as well as for electromagnetic processing of materials (EPM). This document
deals with the significant hazards, hazardous situations or hazardous events relevant to
industrial EH and EPM equipment, as listed in Annex A, for normal operation and for single
fault condition as well as under conditions of reas...view more

IEC 60519-8:2020 specifies particular safety requirements for electroslag remelting equipment and installations.
This document specifies safety requirements applicable to mainly electroheating installations for remelting and, in some cases, for refining processes of metals through direct resistance heating of a conductive slag.
The object of this document is to specify the particular requirements for the safety of persons in or around an electroslag remelting furnace. The general requirements ...view more

IEC 60519-1:2020 is available as IEC 60519-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60519-1:2020 specifies the general safety requirements for industrial installations or equipment intended for electroheating (EH) and electroheating based treatment technologies as well as for electromagnetic processing of materials (EPM). This document deals with the significant hazards, haz...view more

EN-IEC 62282-8-201 defines the evaluation methods of typical performances for electricenergy storage systems using hydrogen. This is applicable to the systems that useelectrochemical reaction devices for both power charge and discharge. This document appliesto systems that are designed and used for service and operation in stationary locations (indoorand outdoor).The conceptual configurations of the electric energy storage systems using hydrogen are shownin Figure 1 and Figure 2. Figure 1 shows ...view more

IEC 63078:2019 specifies the test procedures, conditions and methods for determining the main performance parameters and operational characteristics of induction through-heating installations. Measurements and tests that are solely used for the verification of safety requirements of the installations are outside the scope of this document and are covered by IEC 60519-1 and IEC 60519-3.

IEC 63078:2019 specifies the test procedures, conditions and methods for determining the main performance parameters and operational characteristics of induction through-heating installations.
Measurements and tests that are solely used for the verification of safety requirements of the installations are outside the scope of this document and are covered by IEC 60519-1 and IEC 60519-3.

IEC 60519-12:2016 specifies safety requirements for industrial electroheating equipment and installations in which infrared radiation – usually generated by infrared emitters – is significantly dominating over heat convection or heat conduction as means of energy transfer to the workload. A further limitation of the scope is that the infrared emitters have a maximum spectral emission at longer wavelengths than 780 nm in air or vacuum, and are emitting wideband continuous spectra such...view more

ISO 13578:2017 specifies the general safety requirements for electric arc furnaces (EAF) to melt steel not containing radioactive material. NOTE Radioactive material is considered to be detected in front of the steel plant entrance. ISO 13578:2017 deals with significant hazards, hazardous situations and events as listed in Table 1 pertinent to EAF, when used as intended and under conditions foreseen by the manufacturer, and also includes foreseeable faults and malfunctions in case of misuse. ISO...view more

IEC TS 62996:2017(E) addresses the safety assessments in the frequency range between 1 kHz and 6 MHz and provides limits for touch and touch currents for industrial installations or equipment for electroheating (EH) and electromagnetic processing of materials (EPM). Indirect contact by capacitive currents to parts of an earthed human body in an open space are also included, since the current is then distributed analogously in the part of the body and differs from cases of induced electric shock.

ISO 13579-11:2017 specifies classifications and designations in the methodology of energy efficiency evaluation of industrial furnaces and associated processing equipment (TPE), including energy efficiency in terms of exergy as well as enthalpy. ISO 13579-11:2017does not apply to the following types of TPE: - blast furnaces, basic oxygen furnaces, coke ovens; - furnaces that generate gases to be used as fuel (including by-product gases); - special atmosphere gas generators; - industrial furnaces...view more

IEC/TS 62997:2017(E) specifies the characteristics of external magnetic nearfields, computations of and requirements on induced electric fields in body tissues in the frequency range from 1 Hz to 6 MHz with respect to induced electric shock phenomena, for electroheating (EH) based treatment technologies and for electromagnetic processing of materials (EPM). The phenomena include specific absorption rates with time integration.

IEC 62090:2017 applies to labels on the packaging of electronic components for automatic handling in B2B processes. These labels use linear bar code and two-dimensional (2D) symbols. Labels for direct product marking and shipping labels are excluded. Labels required on the packaging of electronic components that are intended for the retail channel of distribution in B2C processes are also excluded from this document.
Bar code and 2D symbol markings are used, in general, for automatic identifica...view more

IEC 60519-12:2016 specifies safety requirements for industrial electroheating equipment and installations in which infrared radiation – usually generated by infrared emitters – is significantly dominating over heat convection or heat conduction as means of energy transfer to the workload. A further limitation of the scope is that the infrared emitters have a maximum spectral emission at longer wavelengths than 780 nm in air or vacuum, and are emitting wideband continuous spectra such as by therm...view more

ISO 13577-3:2016 specifies safety requirements for generation and use of protective and reactive atmosphere gases that are part of industrial thermo-processing equipment (TPE). NOTE The general safety requirements common to TPE are provided in ISO 13577‑1 (see Introduction). ISO 13577-3:2016 deals with significant hazards, hazardous situations and events relevant to the generation and use of protective and reactive atmosphere gases created by thermochemical reactions and their use in TPE that ar...view more

ISO 13577-1:2016 the general safety requirements common to industrial furnaces and associated processing equipment (TPE). ISO 13577-1:2016 deals with the significant hazards, hazardous situations or hazardous events relevant to TPE, as listed in Annex A, when TPE is used as intended and also under conditions of misuse that are reasonably foreseeable by the manufacturer. Annex B provides a list of common industrial furnaces and associated processing equipment. This document specifies the requirem...view more

The Standard defines safety measures for ovens and dryers in which flammable substances are released by evaporation from and curing of coating materials.

This European Standard deals with all significant hazards, hazardous situations and hazardous events relevant to ovens and dryers in which flammable substances are released by evaporation from and curing of coating materials.
The specific significant risks related to the use of this machinery with foodstuff and pharmaceutical products are not dealt with in this European Standard.
This European Standard is only applicable to machines which are used as intended and under the conditions which are...view more