EN IEC 60519-1:2020

SLOVENSKI STANDARD
01-september-2020
Nadomešča:
SIST EN 60519-1:2015
Varnost pri električnih grelnih inštalacijah in elektromagnetni obdelavi - 1. del:
Splošne zahteve (IEC 60519-1:2020)
Safety in installations for electroheating and electromagnetic processing - Part 1:
General requirements (IEC 60519-1:2020)
Sicherheit in Elektrowärmeanlagen und Anlagen für elektromagnetische
Bearbeitungsprozesse - Teil 1: Allgemeine Anforderungen (IEC 60519-1:2020)
Sécurité dans les installations destinées au traitement électrothermique et
électromagnétique - Partie 1: Exigences générales (IEC 60519-1:2020)
Ta slovenski standard je istoveten z: EN IEC 60519-1:2020
ICS:
25.180.10 Električne peči Electric furnaces
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60519-1

NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 25.180.10 Supersedes EN 60519-1:2015 and all of its amendments
and corrigenda (if any)
English Version
Safety in installations for electroheating and electromagnetic
processing - Part 1: General requirements
(IEC 60519-1:2020)
Sécurité dans les installations destinées au traitement Sicherheit in Elektroerwärmungsanlagen und Anlagen für
électrothermique et électromagnétique - Partie 1: Exigences elektromagnetische Bearbeitungsprozesse - Teil 1:
générales Allgemeine Anforderungen
(IEC 60519-1:2020) (IEC 60519-1:2020)
This European Standard was approved by CENELEC on 2020-04-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60519-1:2020 E

European foreword
The text of document 27/1121/FDIS, future edition 6 of IEC 60519-1, prepared by IEC/TC 27
"Industrial electroheating and electromagnetic processing" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 60519-1:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-01-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-04-15
document have to be withdrawn
This document supersedes EN 60519-1:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 60519-1:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60079 series NOTE Harmonized as EN 60079 series
IEC 60335 series NOTE Harmonized as EN 60335 series
IEC 60519 series NOTE Harmonized as EN 60519 series
IEC 60601 series NOTE Harmonized as EN 60601 series
IEC 60974 series NOTE Harmonized as EN 60974 series
IEC 61010 series NOTE Harmonized as EN 61010 series
IEC 61140:2016 NOTE Harmonized as EN 61140:2016 (not modified)
IEC 62226 series NOTE Harmonized as EN 62226 series
IEC 62311 NOTE Harmonized as EN IEC 62311
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60071-1 2006  Insulation co-ordination - Part 1: EN 60071-1 2006
Definitions, principles and rules
+A1 2010 +A1 2010
IEC 60204-1 2016 Safety of machinery - Electrical equipment EN 60204-1 2018
of machines - Part 1: General requirements
IEC 60204-11 2018 Safety of machinery - Electrical equipment EN IEC 60204-11 2019
of machines - Part 11: Requirements for
equipment for voltages above 1 000 V AC
or 1 500 V DC and not exceeding 36 kV
- -  +corrigendum Feb. 2010
IEC 60228 2004 Conductors of insulated cables EN 60228 2005
+ A1 2013  - -
+ A2 2016  - -
IEC 60335-1 (mod) 2010 Household and similar electrical appliances EN 60335-1 2012
- Safety - Part 1: General requirements
- -  +A11 2014
+A13 2017
+A14 2019
+A1 2013  +A1 2019
+A2 2016 +A2 2019
IEC 60335-2-24 - Household and similar electrical appliances EN 60335-2-24 2010
- Safety - Part 2-24: Particular
requirements for refrigerating appliances,
ice-cream appliances and ice makers
IEC 60335-2-89 -  Household and similar electrical appliances EN 60335-2-89 2010
- Safety - Part 2-89: Particular
requirements for commercial refrigerating
appliances with an incorporated or remote
refrigerant condensing unit or compressor
- - +A1 2016
+A2 2017
IEC 60364-1 (mod) 2005 Low-voltage electrical installations - Part 1: HD 60364-1 2008
Fundamental principles, assessment of
general characteristics, definitions
- - +A11 2017
IEC 60364-4-41 2005  Low-voltage electrical installations - Part 4-HD 60364-4-41 2017
(mod) 41: Protection for safety - Protection
against electric shock
- -  +A11 2017
+A12 2019
+A1 2017
IEC 60364-4-42 2010 Low-voltage electrical installations - Part 4-HD 60364-4-42 2011
42: Protection for safety - Protection
against thermal effects
+A1 2014 +A1 2015
IEC 60364-4-44 2007  Low-voltage electrical installations - Part 4-HD 60364-4-442 2012
(mod) 44: Protection for safety - Protection
against voltage disturbances and
electromagnetic disturbances
+A1 (mod) 2015 HD 60364-4-443 2016
+A2 2018
IEC 60364-5-53 2001  Electrical installations of buildings - Part 5-- -
53: Selection and erection of electrical
equipment - Isolation, switching and control
+ A1 (mod) 2002 HD 60364-5-534 2016
+ A2 (mod) 2015
IEC 60364-5-54 2011  Low-voltage electrical installations - Part 5-HD 60364-5-54 2011
54: Selection and erection of electrical
equipment - Earthing arrangements and
protective conductors
- - +A11 2017
IEC 60398 2015  Installations for electroheating and IEC 60398 2015
electromagnetic processing - General
performance test methods
IEC 60417 -  Graphical symbols for use on equipment - -
IEC 60445 2017  Basic and safety principles for man-EN 60445 2017
machine interface, marking and
identification - Identification of equipment
terminals, conductor terminations and
conductors
IEC 60529 1989  Degrees of protection provided by EN 60529 1991
enclosures (IP Code)
+ A1 1999 +A1 2000
+A2 2013 +A2 2013
IEC 60664-1 2007 Insulation coordination for equipment EN 60664-1 2007
within low-voltage systems - Part 1:
Principles, requirements and tests
IEC 60825-1 2014 Safety of laser products - Part 1: EN 60825-1 2014
Equipment classification and requirements
IEC 60865-1 2011 Short-circuit currents - Calculation of EN 60865-1 2012
effects - Part 1: Definitions and calculation
methods
IEC 60909-0 2016  Short-circuit currents in three-phase a.c. EN 60909-0 2016
systems - Part 0: Calculation of currents
IEC 60990 2016 Methods of measurement of touch current EN 60990 2016
and protective conductor current
IEC 61000-6-2 2016 Electromagnetic compatibility (EMC) - PartEN IEC 61000-6-2 2019
6-2: Generic standards - Immunity
standard for industrial environments
IEC 61000-6-7 2014 Electromagnetic compatibility (EMC) - PartE N 61000-6-7 2015
6-7: Generic standards - Immunity
requirements for equipment intended to
perform functions in a safety-related
system (functional safety) in industrial
locations
IEC 61010-1 2010 Safety requirements for electrical EN 61010-1 2010
equipment for measurement, control and
laboratory use - Part 1: General
requirements
+ A1 2016 +A1 2019
IEC 61082-1 2014 Preparation of documents used in EN 61082-1 2015
electrotechnology - Part 1: Rules
IEC 61310-1 2007 Safety of machinery - Indication, marking EN 61310-1 2008
and actuation -- Part 1: Requirements for
visual, acoustic and tactile signals
IEC 61310-2 2007 Safety of machinery - Indication, marking EN 61310-2 2008
and actuation -- Part 2: Requirements for
marking
IEC 61310-3 2007 Safety of machinery - Indication, marking EN 61310-3 2008
and actuation -- Part 3: Requirements for
the location and operation of actuators
IEC 61439 series Low-voltage switchgear and control gear EN 61439 series
assemblies
IEC 61508-1 2010 Functional safety of EN 61508-1 2010
electrical/electronic/programmable
electronic safety-related systems -- Part 1:
General requirements
IEC 61786-1 2013  Measurement of DC magnetic, AC EN 61786-1 2014
magnetic and AC electric fields from 1 Hz
to 100 kHz with regard to exposure of
human beings - Part 1: Requirements for
measuring instruments
1)
IEC 61786-2 2014  Measurement of low-frequency magnetic - -
and electric fields with regard to exposure
of human beings - Part 2: Guidance for
measurements
IEC 61936-1 (mod) 2010 Power installations exceeding 1 kV a.c. - EN 61936-1 2010
Part 1: Common rules
+ A1 2014  + A1 2014
IEC 62061 2005 Safety of machinery - Functional safety of EN 62061 2005
safety-related electrical, electronic and
programmable electronic control systems
+ A1 2012  + A1 2013
+ A2 2015 + A2 2015
IEC 62271 series High-voltage switchgear and controlgear EN 62271 series
IEC 62471 (mod) 2006 Photobiological safety of lamps and lamp EN 62471 2008
systems
IEC 82079-1 2012  Preparation of instructions for use - EN 82079-1 2012
Structuring, content and presentation - Part
1: General principles and detailed
requirements
CISPR 11 (mod) 2015  Industrial, scientific and medical equipment EN 55011 2016
- Radio-frequency disturbance
characteristics - Limits and methods of
measurement
+ A1 2016 + A1 2017
+ A2 2019
IEEE C95.1 2005 IEEE Standard for Safety Levels with - -
Respect to Human Exposure to Radio
Frequency Electromagnetic Fields, 3 kHz
to 300 GHz
1)
Dated as no equivalent European Standard exist.
IEEE C95.6 2002 IEEE Standard for Safety Levels with - -
Respect to Human Exposure to
Electromagnetic Fields, 0–3 kHz
ISO 3864-1 2011  Graphical symbols - Safety colours and - -
safety signs - Part-1: Design principles for
safety signs and safety markings
ISO 6385 2016  Ergonomics principles in the design of EN ISO 6385 2016
work systems (ISO 6385:2016)
1)
ISO 7000 2019 Graphical symbols for use on equipment - - -
Registered symbols
ISO 7010 - Graphical symbols - Safety colours and EN ISO 7010 2020
safety signs - Registered safety signs
ISO 12100 2010 Safety of machinery - General principles EN ISO 12100 2010
for design - Risk assessment and risk
reduction
ISO 13577-1 2016  Industrial furnaces and associated - -
processing equipment - Safety - Part 1:
General requirements
ISO 13577-2 2014  Industrial furnaces and associated - -
processing equipment - Safety - Part 2:
Combustion and fuel handling systems
ISO 13577-3 2016 Industrial furnaces and associated
processing equipment - Safety - Part 3:
Generation and use of protective and
reactive atmosphere gases
ISO 13732-1 2006 Ergonomics of the thermal environment - EN ISO 13732-1 2008
Methods for the assessment of human
responses to contact with surfaces - Part 1:
Hot surfaces
ISO 13849-1 2015 Safety of machinery - Safety-related parts EN ISO 13849-1 2015
of control systems
ISO 13850 2015  Safety of machinery - Emergency stop - EN ISO 13850 2015
Principles for design
ISO 13855 2010 Safety of machinery - Positioning of EN ISO 13855 2010
safeguards with respect to the approach
speeds of parts of the human body
ISO 13857 2008 Safety of machinery - Safety distances to EN ISO 13857 2008
prevent hazard zones being reached by
upper and lower limbs
ISO 14119 2013 Safety of machinery - Interlocking devices EN ISO 14119 2013
associated with guards - Principles for
design and selection
ISO 14120 2015 Safety of machinery – Guards - General EN ISO 14120 2015
requ
...