iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60534-8-1:2000

(Main)

Industrial-process control valves - Part 8: Noise considerations - Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

Industrial-process control valves - Part 8: Noise considerations - Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

Defines equipment, methods and procedures for obtaining laboratory measurements of airborne sound-pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Provides a method of testing the noise-generating characteristics of control valves. The noise characteristics to be determined are useful for comparing the performance of different valves and planning measures for noise abatement.

Stellventile für die Prozeßregelung - Teil 8: Geräuschbetrachtungen - Hauptabschnitt 1: Laboratoriummessungen von Geräuschen bei gasdurchströmten Stellventilen

Vannes de régulation des processus industriels - Partie 8: Considérations sur le bruit - Section 1: Mesure en laboratoire du bruit créé par un débit aérodynamique à travers une vanne de régulation

Définit le matériel, les méthodes et les procédures pour obtenir des mesures en laboratoire des niveaux de pression acoustique aérienne rayonnée par les vannes régulation et/ou les configurations de tuyauteries associées, à travers lesquelles passent des fluides compressibles. Fournit une méthode d'essai des caractéristiques génératrices de bruit d'une vanne de régulation. Une méthode unifiée de mesure de bruit généré par la vanne et les tuyauteries d'essai associées permet une comparaison des différents résultats de mesure, qui est bénéfique à la fois à l'utilisateur et au fabricant. Les critères de bruit sont exprimés en déterminant le niveau de pression acoustique (NPA) de la vanne considérée. Les caractéristiques de bruit à déterminer sont utiles pour comparer le fonctionnement de différentes vannes, et prendre les dispositions pour atténuer le bruit.

Industrial-process control valves - Part 8: Noise considerations - Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves (IEC 60534 -8-1:1986)

General Information

Status
Withdrawn
Publication Date
24-Oct-2000
Withdrawal Date
31-Jul-2003
ICS
17.140.20 - Noise emitted by machines and equipment
23.060.40 - Pressure regulators
25.040.40 - Industrial process measurement and control
Technical Committee
CLC/SR 65B - Devices & process analysis
Drafting Committee
IEC/SC 65B - IEC_SC_65B
Parallel Committee
IEC/SC 65B - IEC_SC_65B
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Sep-2008
Completion Date
01-Sep-2008
Ref Project
SIST EN 60534-8-1:2001 - Industrial-process control valves -- Part 8: Noise considerations -- Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

Relations

Replaced By
EN 60534-8-1:2005 - Industrial-process control valves - Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
Effective Date
29-Jan-2023

Buy Standard

EN 60534-8-1:2001EN 60534-8-1:2001
PreviousNext
Standard
EN 60534-8-1:2001
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2001
Industrial-process control valves - Part 8: Noise considerations - Section 1:
Laboratory measurement of noise generated by aerodynamic flow through control
valves (IEC 60534 -8-1:1986)
Industrial-process control valves -- Part 8: Noise considerations -- Section 1: Laboratory
measurement of noise generated by aerodynamic flow through control valves
Stellventile für die Prozeßregelung -- Teil 8: Geräuschbetrachtungen -- Hauptabschnitt 1:
Laboratoriummessungen von Geräuschen bei gasdurchströmten Stellventilen
Vannes de régulation des processus industriels -- Partie 8: Considérations sur le bruit --
Section 1: Mesure en laboratoire du bruit créé par un débit aérodynamique à travers une
vanne de régulation
Ta slovenski standard je istoveten z: EN 60534-8-1:2000
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 60534-8-4:2015(Main)
Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow
SIST EN 60534-8-4:2016

IEC 60534-8-4:2015 establishes a method to predict the noise generated in a control valve by liquid flow and the resulting noise level measured downstream of the valve and outside of the pipe. The noise may be generated both by normal turbulence and by liquid cavitation in the valve. Parts of the method are based on fundamental principles of acoustics, fluid mechanics, and mechanics. The method is validated by test data. This third edition cancels and replaces the second edition published 2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Hydrodynamic noise is predicted as a function of frequency and b) Elimination of the acoustic power ratio.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60534-8-2:2011(Main)
Industrial-process control valves - Part 8-2: Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves
SIST EN 60534-8-2:2012

IEC 60534-8-2:2011 includes the method for measuring the sound pressure level due to liquid flow through a control valve and the method for determining the characteristic increase of noise due to the onset of cavitation. It also defines the equipment, methods and procedures for the laboratory measurement of the airborne sound needed to determine these characteristics. Two methods are provided for testing the noise generating characteristics of control valves. The first is a uniform method of measuring the radiated noise from the valve and the associated test piping including fixed flow restrictions through which the test fluid (water) is passing. The second is a procedure for measuring the sound pressure levels within pipe systems upstream and downstream of the valve under fixed operating conditions. This second edition cancels and replaces the first edition published in 1991 and constitutes a technical revision that includes internal noise measurement.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60534-8-3:2011(Main)
Industrial-process control valves - Part 8-3: Noise considerations - Control valve aerodynamic noise prediction method
SIST EN 60534-8-3:2011

IEC 60534-8-3:2010 establishes a theoretical method to predict the external sound-pressure level generated in a control valve and within adjacent pipe expanders by the flow of compressible fluids. This method considers only single-phase dry gases and vapours and is based on the perfect gas laws. It is assumed that the downstream piping is straight for a length of at least 2 m from the point where the noise measurement is made. The method is applicable to the following single-stage valves: - globe (straight pattern and angle pattern), - butterfly, - rotary plug (eccentric, spherical), - ball, and - valves with cage trims. Specifically excluded are the full bore ball valves where the product FpC exceeds 50 % of the rated flow coefficient. This third edition cancels and replaces the second edition published in 2000. This edition constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: - predicting noise as a function of frequency; - using laboratory data to determine the acoustical efficiency factor.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60534-8-1:2005(Main)
Industrial-process control valves - Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
SIST EN 60534-8-1:2007

Defines equipment, methods, and procedures for obtaining laboratory measurements of sound pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Control valves discharging to atmosphere are excluded from this standard

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-9:2024(Main)
Rotating electrical machines - Part 9: Noise limits
SIST EN IEC 60034-9:2025

IEC 60034-9:2021 specifies test methods for the determination of sound power level of rotating electrical machines and specifies maximum A-weighted sound power levels for factory acceptance testing of network-supplied, rotating electrical machines in accordance with lEC 60034-1, having methods of cooling according to lEC 60034-6 and degrees of protection according to lEC 60034-5, and having the following characteristics: - standard design, either AC or DC, without additional special electrical, mechanical, or acoustical modifications intended to reduce the sound power level - rated output from 1 kW (or kVA) up to and including 5 500 kW (or kVA) - rated speed not greater than 3 750 min–1 This fifth edition cancels and replaces the fourth edition, published in 2003 and its amendment 1, published in 2007. This edition includes the following significant technical changes with respect to the previous edition: a) In Table 2 and Table 3 cooling methods IC01, IC11, IC21 and IC31, IC71, IC81 are now covered. b) This edition adds Table 3 for 60 Hz machines, whereas Table 2, which covers only 50 Hz machines, has no change in levels. c) In Table 3, grade A is added to harmonize the highest levels seen in IEC and NEMA, whereas grade B was added to harmonize the lowest, more restrictive levels seen in IEC and NEMA. d) The clause “Determination of noise increments caused by converter supply” has been shifted to Annex B and renamed “Information on typical noise increments caused by converter supply”.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-12:2024(Main)
Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors
SIST EN IEC 60034-12:2025

IEC 60034-12:2024 is available as IEC 60034-12:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60034-12:2024 specifies the parameters for eight designs of starting performance of single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with IEC 60034‑1 that: - have a rated voltage up to 1 000 V; - are intended for direct-on-line or star-delta starting; - are rated on the basis of duty type S1; - are constructed to any degree of protection as defined in IEC 60034-5 and explosion protection. This document also applies to dual voltage motors provided that the flux saturation level is the same for both voltages. This fourth edition cancels and replaces the third edition published in 2016. Aligned with the requirements for explosion protected motors from TC31 WG27 - new clause on methods for measuring locked-rotor current and torque; - new informative annex on the general current and torque characteristics with locked rotor; - new informative annex on correction of voltage and frequency; - aligned with the requirements for explosion protected motors from TC31 WG27.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-39:2024(Main)
Household and similar electrical appliances - Safety - Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans
SIST EN IEC 60335-2-39:2025

IEC 60335-2-39:2012 deals with the safety of electrically operated commercial multi-purpose cooking pans not intended for household and similar use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. This standard also deals with pressurized appliances and appliances with pressurized parts. These appliances are used for processing food for commercial consumption, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries, butcheries, etc. The electrical part of appliances making use of other forms of energy is also within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by these types of appliances. Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. The principal changes in this edition as compared with the fifth edition of IEC 60335-2-39 are as follows (minor changes are not listed): - addition to definition of portable appliances, atmospheric multi-purpose cooking and rated pressure; - deletion of equipotential symbol 5021 of IEC 60417 covered by Part 1; - addition of instructions for multi-purpose cooking pans; - modification on leakage current permissible for portable class l appliances; - addition to abnormal test requirements; - addition to mechanical hazard test for multi-purpose cooking pans; - addition of construction test for multi-purpose cooking pans; - addition to construction requirements for lids and theirs grips; - addition to construction requirements for positioning of pressure reliefs; - addition to construction's fixed appliances which are moved forward and backward for cleaning purposes.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Keywords: Multi-purpose cooking pans.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-40:2024(Main)
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
SIST EN IEC 60335-2-40:2025

This European Standard deals with the safety of electric heat pumps, sanitary hot water heat pumps and air conditioners, incorporating motor-compressors as well as hydronic fan coils units, dehumidifiers (with or without motor-compressors), thermoelectric heat pumps and partial units. Their maximum rated voltage being not more than 300 V for single phase appliances and 600 V for multi-phase appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.

  • Draft
    158 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-40:2024/A11:2024(Amendment)
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
SIST EN IEC 60335-2-40:2025/A11:2025

This European Standard deals with the safety of electric heat pumps, sanitary hot water heat pumps and air conditioners, incorporating motor-compressors as well as hydronic fan coils units, dehumidifiers (with or without motor-compressors), thermoelectric heat pumps and partial units. Their maximum rated voltage being not more than 300 V for single phase appliances and 600 V for multi-phase appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-11:2024(Main)
Rotating electrical machines - Part 11: Thermal protection
SIST EN IEC 60034-11:2025

IEC 60034-11:2020 is available as IEC 60034-11:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60034-11:2020 specifies requirements relating to the use of thermal protectors and thermal detectors incorporated into the stator windings or placed in other suitable positions in induction machines in order to protect them against serious damage due to thermal overloads. It applies to single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with IEC 60034-1 and IEC 60034-12 that: - have a rated voltage up to 1 000 V; - are intended for direct-on-line or star-delta starting. The main changes with respect to the previous edition are: - the additional specification of winding temperature limits for temperature class 200 (N), - the increased limits of maximum winding temperatures for overloads with rapid variation, - the clarification that the motor winding may be permanently damaged after it has been exposed to temperatures - a clarification of the definition of indirect thermal protection, - a clarification on the test methods for larger motors.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day