iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61709:2011

(Main)

Electric components - Reliability - Reference conditions for failure rates and stress models for conversion

Electric components - Reliability - Reference conditions for failure rates and stress models for conversion

IEC 61709:2011 gives guidance on how failure rate data can be employed for reliability prediction of electric components in equipment. Reference conditions are numerical values of stresses that are typically observed by components in the majority of applications. Reference conditions are useful since they are the basis of the calculation of failure rate under any conditions by the application of stress models that take into account the actual operating conditions. This standard also gives guidance on how a database of component failure data can be constructed to provide failure rates that can be used with the included stress models. This edition includes the following significant technical changes with respect to the previous edition: - the addition of a number of component types and the updating of models for a large number of component types; - the addition of annexes on reliability prediction, sources of failure rate data and component classification information.

Elektrische Bauelemente - Zuverlässigkeit - Referenzbedingungen für Ausfallraten und Beanspruchungsmodelle zur Umrechnung

Composants électriques - Fiabilité - Conditions de référence pour les taux de défaillance et modèles de contraintes pour la conversion

La CEI 61709:2011 donne des recommandations concernant les méthodes d'utilisation des données de taux de défaillance pour les prévisions de fiabilité de composants électriques d'équipements. Les conditions de référence sont des valeurs numériques de contraintes généralement observées sur les composants dans la plupart des applications. Ces conditions de référence sont utiles dans la mesure où elles permettent de calculer le taux de défaillance dans toutes conditions, en appliquant des modèles de contrainte qui tiennent compte des conditions de fonctionnement réelles. La présente norme donne également des recommandations concernant les méthodes pour constituer une base de données de taux de défaillance des composants afin que les taux fournis puissent être employés avec les modèles de contrainte fournis. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - l'addition de plusieurs types de composants et l'actualisation des modèles pour nombreux types de composants; - l'addition des annexes relatives aux prévisions de fiabilité, des sources des données de taux de défaillance et des informations relatives au classification des composants.

Električne komponente - Zanesljivost - Referenčni pogoji za pogostost odpovedi in modele obremenjevanja za pretvarjanje

Ta mednarodni standard podaja vodilo o uporabi podatkov o pogostosti odpovedi za napovedovanje zanesljivosti električnih komponent v opremi. Referenčni pogoji so številčne vrednosti obremenitev, ki se praviloma opazijo pri komponentah večine aplikacij. Referenčni pogoji so uporabni, ker so osnova za izračun pogostosti odpovedi pri vseh pogojih z uporabo modelov obremenjevanja, ki upoštevajo dejanske obratovalne razmere. Pogostosti odpovedi, navedene za referenčne pogoje, omogočajo realistično napovedovanje zanesljivosti v zgodnji fazi načrtovanja. Tu opisani modeli obremenjevanja so generični in se po potrebi lahko uporabijo kot osnova za pretvarjanje podatkov o pogostosti odpovedi pri teh referenčnih pogojih v dejanske obratovalne razmere, kar poenostavi napovedni pristop. Pretvarjanje podatkov o pogostosti odpovedi je dovoljeno le v določenih funkcionalnih omejitvah komponent. Ta standard tudi podaja vodilo o pripravi baze podatkov o odpovedi komponent, ki navaja pogostosti odpovedi, ki se lahko uporabijo z vključenimi modeli obremenjevanja. Določeni so referenčni pogoji za podatke o pogostosti odpovedi, kar omogoča enotno primerjavo podatkov iz različnih virov. Če so podatki o pogostosti odpovedi navedeni v skladu s tem mednarodnim standardom, dodatne informacije o točno določenih pogojih niso potrebne. Ta standard ne podaja osnovnih pogostosti odpovedi za komponente, pač pa zagotavlja modele, ki omogočajo pretvorbo pogostosti odpovedi, pridobljenih drugače, iz enih obratovalnih razmer v druge. Metodologija napovedovanja, opisana v tem standardu, predvideva, da se deli uporabljajo v okviru svoje življenjske dobe. Metode v tem standardu imajo splošno uporabo, vendar se specifično uporabljajo za izbor vrst komponent, kot je opredeljeno v točki 6 in točki E.2.

General Information

Status
Withdrawn
Publication Date
11-Aug-2011
Withdrawal Date
28-Jul-2014
ICS
31.020 - Electronic components in general
Technical Committee
CLC/SR 56 - Dependability
Drafting Committee
IEC/TC 56 - IEC_TC_56
Parallel Committee
IEC/TC 56 - IEC_TC_56
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
24-Mar-2020
Completion Date
24-Mar-2020
Ref Project
SIST EN 61709:2011 - Electric components - Reliability - Reference conditions for failure rates and stress models for conversion

Relations

Replaces
EN 61709:1998 - Electronic components - Reliability - Reference conditions for failure rates and stress models for conversion
Effective Date
29-Jan-2023
Replaced By
EN 61709:2017 - Electric components - Reliability - Reference conditions for failure rates and stress models for conversion
Effective Date
07-Jun-2022

Buy Standard

EN 61709:2011EN 61709:2011
PreviousNext
Standard
EN 61709:2011
English language
92 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2011
(OHNWULþQHNRPSRQHQWH=DQHVOMLYRVW5HIHUHQþQLSRJRML]DSRJRVWRVWRGSRYHGLLQ
PRGHOHREUHPHQMHYDQMD]DSUHWYDUMDQMH
Electric components - Reliability - Reference conditions for failure rates and stress
models for conversion
Composants électriques - Fiabilité - Conditions de référence pour les taux de défaillance
et modèles de contraintes pour la conversion
Ta slovenski standard je istoveten z: EN 61709:2011
ICS:
21.020 =QDþLOQRVWLLQQDþUWRYDQMH Characteristics and design of
VWURMHYDSDUDWRYRSUHPH machines, apparatus,
equipment
31.020 Elektronske komponente na Electronic components in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61709
NORME EUROPÉENNE
August 2011
EUROPÄISCHE NORM
ICS 31.020 Supersedes EN 61709:1998

English version
Electric components -
Reliability -
Reference conditions for failure rates and stress models for conversion
(IEC 61709:2011)
Composants électriques -  Elektrische Bauelemente -
Fiabilité - Zuverlässigkeit -
Conditions de référence pour les taux de Referenzbedingungen für Ausfallraten und
défaillance et modèles de contraintes pour Beanspruchungsmodelle zur Umrechnung
la conversion (IEC 61709:2011)
(CEI 61709:2011)
This European Standard was approved by CENELEC on 2011-07-29. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61709:2011 E
Foreword
The text of document 56/1422/FDIS, future edition 2 of IEC 61709, prepared by IEC TC 56,
Dependability, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 61709 on 2011-07-29.
This European Standard supersedes EN 61709:1998.
– the addition of a number of component types and the updating of models for a large number of
component types;
– the addition of annexes on reliability prediction, sources of failure rate data and component
classification information.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2012-04-29
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-07-29
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61709:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60300-3-2:2004 NOTE  Harmonized as EN 60300-3-2:2005 (not modified).
IEC 60721 series NOTE  Harmonized in EN 60721 series.
IEC 61360 series NOTE  Harmonized in EN 61360 series.
IEC 61360-1:2009 NOTE  Harmonized as EN 61360-1:2010 (not modified).
IEC 61360-4:2005 NOTE  Harmonized as EN 61360-4:2005 (not modified).
IEC 61649:2008 NOTE  Harmonized as EN 61649:2008 (not modified).
IEC 61703 NOTE  Harmonized as EN 61703.
IEC 62308 NOTE  Harmonized as EN 62308.
ISO 10303-11:1994 NOTE  Harmonized as EN ISO 10303-11:1995 (not modified).
ISO 10303-31 NOTE  Harmonized as EN ISO 10303-31.
__________
- 3 - EN 61709:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60050-191 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 191: Dependability and quality of
service
IEC 60605-6 - Equipment reliability testing - - -
Part 6: Tests for the validity and estimation of
the constant failure rate and constant failure
intensity
IEC 60721-3-3 - Classification of environmental conditions - EN 60721-3-3 -
Part 3: Classification of groups of
environmental parameters and
their severities -
Section 3: Stationary use at weatherprotected
locations
IEC 60721-3-4 - Classification of environmental conditions - EN 60721-3-4 -
Part 3: Classification of groups of
environmental parameters and
their severities -
Section 4: Stationary use at non-
weatherprotected locations
IEC 60721-3-5 - Classification of environmental conditions - EN 60721-3-5 -
Part 3: Classification of groups of
environmental parameters and
their severities -
Section 5: Ground vehicle installations

IEC 60721-3-7 - Classification of environmental conditions - EN 60721-3-7 -
Part 3: Classification of groups of
environmental parameters and
their severities -
Section 7: Portable and non-stationary use

IEC 61709 ®
Edition 2.0 2011-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric components – Reliability – Reference conditions for failure rates and
stress models for conversion
Composants électriques – Fiabilité – Conditions de référence pour les taux
de défaillance et modèles de contraintes pour la conversion

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XD
ICS 31.020 ISBN 978-2-88912-551-7

– 2 – 61709 © IEC:2011
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms, definitions and symbols . 10
3.1 Terms and definitons . 10
3.2 Symbols . 12
4 Context and conditions . 13
4.1 Failure modes . 13
4.2 Operating profile considerations . 14
4.3 Storage conditions . 14
4.4 Environmental conditions . 14
5 Generic reference conditions and stress models . 16
5.1 Recommended generic reference conditions . 16
5.2 Generic stress models . 17
5.2.1 General . 17
5.2.2 Stress factor for voltage dependence, π . 18
U
5.2.3 Stress factor for current dependence, π . 18
I
5.2.4 Stress factor for temperature dependence, π . 18
T
5.2.5 Environmental application factor, π . 20
E
5.2.6 Other factors of influence . 21
6 Specific reference conditions and stress models. 21
6.1 Integrated semiconductor circuits . 21
6.1.1 Reference conditions . 21
6.1.2 Stress factors . 23
6.2 Discrete semiconductors . 27
6.2.1 Reference conditions . 27
6.2.2 Stress factors . 28
6.3 Optoelectronic components . 32
6.3.1 Reference conditions . 32
6.3.2 Stress factors . 34
6.4 Capacitors . 38
6.4.1 Reference conditions . 38
6.4.2 Stress factors . 38
6.5 Resistors and resistor networks . 41
6.5.1 Reference conditions . 41
6.5.2 Stress factors . 42
6.6 Inductors, transformers and coils . 43
6.6.1 Reference conditions . 43
6.6.2 Stress factors . 43
6.7 Microwave devices . 44
6.7.1 Reference conditions . 44
6.7.2 Stress factors . 45
6.8 Other passive components . 45
6.8.1 Reference conditions . 45

61709 © IEC:2011 – 3 –
6.8.2 Stress factors . 45
6.9 Electrical connections. 45
6.9.1 Reference conditions . 45
6.9.2 Stress factors . 46
6.10 Connectors and sockets . 46
6.10.1 Reference conditions . 46
6.10.2 Stress factors . 46
6.11 Relays . 46
6.11.1 Reference conditions . 46
6.11.2 Stress factors . 47
6.12 Switches and push-buttons . 49
6.12.1 Reference conditions . 49
6.12.2 Stress factors . 50
6.13 Signal and pilot lamps .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61163-2:2020(Main)
Reliability stress screening - Part 2: Components
SIST EN IEC 61163-2:2020

IEC 61163-2:2020 provides guidance on RSS techniques and procedures for electrical, electronic, and mechanical components. This document is procedural in nature and is not, and cannot be, exhaustive with respect to component technologies due to the rapid rate of developments in the component industry. This document is: a) intended for component manufacturers as a guideline; b) intended for component users as a guideline to negotiate with component manufacturers on RSS requirements; c) intended to allow the planning of an RSS process in house to meet reliability requirements or to allow the re-qualification of components for specific, upgraded, environments; d) intended as a guideline to sub-contractors who provide RSS as a service. This document is not intended to provide test plans for specific components or for delivery of certificates of conformance for batches of components. The use of bi-modal Weibull analysis to select and optimize an RSS process without having to estimate the reliability and life time of all items is described. This second edition cancels and replaces the first edition published in 1998. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) this version of the document is a complete rewrite and restructure from the previous version.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61709:2017/AC:2019-11(Corrigendum)
Electric components - Reliability - Reference conditions for failure rates and stress models for conversion
SIST EN 61709:2017/AC:2020

This document gives guidance on the use of failure rate data for reliability prediction of
electric components used in equipment.
The method presented in this document uses the concept of reference conditions which are
the typical values of stresses that are observed by components in the majority of applications.
Reference conditions are useful since they provide a known standard basis from which failure
rates can be modified to account for differences in environment from the environments taken
as reference conditions. Each user can use the reference conditions defined in this document
or use their own. When failure rates stated at reference conditions are used it allows realistic
reliability predictions to be made in the early design phase.
The stress models described herein are generic and can be used as a basis for conversion of
failure rate data given at these reference conditions to actual operating conditions when
needed and this simplifies the prediction approach. Conversion of failure rate data is only
possible within the specified functional limits of the components.
This document also gives guidance on how a database of component failure data can be
constructed to provide failure rates that can be used with the included stress models.
Reference conditions for failure rate data are specified, so that data from different sources
can be compared on a uniform basis. If failure rate data are given in accordance with this
document then additional information on the specified conditions can be dispensed with.
This document does not provide base failure rates for components – rather it provides models
that allow failure rates obtained by other means to be converted from one operating condition
to another operating condition.
The prediction methodology described in this document assumes that the parts are being
used within its useful life. The methods in this document have a general application but are
specifically applied to a selection of component types as defined in Clauses 6 to 20 and I.2.

  • Corrigendum
    3 pages
    French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61709:2017(Main)
Electric components - Reliability - Reference conditions for failure rates and stress models for conversion
SIST EN 61709:2017

NEW!IEC 61709:2017 is available as IEC 61709:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61709:2017 gives guidance on the use of failure rate data for reliability prediction of electric components used in equipment. The method presented in this document uses the concept of reference conditions which are the typical values of stresses that are observed by components in the majority of applications. Reference conditions are useful since they provide a known standard basis from which failure rates can be modified to account for differences in environment from the environments taken as reference conditions. Each user can use the reference conditions defined in this document or use their own. When failure rates stated at reference conditions are used it allows realistic reliability predictions to be made in the early design phase. The stress models described herein are generic and can be used as a basis for conversion of failure rate data given at these reference conditions to actual operating conditions when needed and this simplifies the prediction approach. Conversion of failure rate data is only possible within the specified functional limits of the components. This document also gives guidance on how a database of component failure data can be constructed to provide failure rates that can be used with the included stress models. Reference conditions for failure rate data are specified, so that data from different sources can be compared on a uniform basis. If failure rate data are given in accordance with this document then additional information on the specified conditions can be dispensed with. This document does not provide base failure rates for components – rather it provides models that allow failure rates obtained by other means to be converted from one operating condition to another operating condition. The prediction methodology described in this document assumes that the parts are being used within its useful life. The methods in this document have a general application but are specifically applied to a selection of component types as defined in Clauses 6 to 20 and I.2. This third edition cancels and replaces the second edition, published in 2011. This edition constitutes a technical revision. This third edition is a merger of IEC 61709:2011 and IEC TR 62380:2004. This edition includes the following significant technical changes with respect to the previous edition: addition of 4.5 Components choice, 4.6 Reliability growth during the deployment phase of new equipment, 4.7 How to use this document, and of Clause 19 Printed circuit boards (PCB) and Clause 20 Hybrid circuits with respect to IEC TR 62380; addition of failure modes of components in Annex A; modification of Annex B, Thermal model for semiconductors, adopted and revised from IEC TR 62380; modification of Annex D, Considerations on mission profile; modification of Annex E, Useful life models, adopted and revised from IEC TR 62380; revision of Annex F (former B.2.6.4), Physics of failure; addition of Annex G (former Annex C), Considerations for the design of a data base on failure rates, complemented with parts of IEC 60319; addition of Annex H, Potential sources of failure rate data and methods of selection; addition of Annex J, Presentation of component reliability data, based on IEC 60319. Keywords: failure rate data, reliability prediction of electric components

  • Standard
    124 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63203-402-2:2024(Main)
Wearable electronic devices and technologies - Part 402-2: Performance measurement of fitness wearables - Step counting
SIST EN IEC 63203-402-2:2024

IEC 63203-402-2:2024 specifies test methods for measuring and evaluating the performance, reliability, and accuracy of the step counting feature in any wearable device that can count steps (e.g. activity and fitness trackers, smart bands, smart shoes, and smart insoles). These standard test methods exclude the evaluation of data associated with travel distance or calorie consumption.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63203-402-3:2024(Main)
Wearable electronic devices and technologies - Part 402-3: Performance measurement of fitness wearables - Test methods for the determination of the accuracy of heart rate
SIST EN IEC 63203-402-3:2024

IEC 63203-402-3:2024 specifies terms, a measurement protocol, and a test to evaluate the accuracy of wearables that measure heart rate with a photoplethysmography (PPG) sensor. While this document can be used to measure a variety of different devices claiming to report heart rate, care will be taken when testing in countries that differentiate between heart rate and pulse rate. This measurement protocol is not intended to evaluate medical devices associated with the IEC 60601 series or ISO 80601 series.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60938-2-1:2024(Main)
Fixed inductors for electromagnetic interference suppression - Part 2-1: Blank detail specification - Inductors for which safety tests are required
SIST EN IEC 60938-2-1:2024

IEC 60938-2-1:2023 is applicable to the drafting of detail specifications for fixed inductors for which safety tests are required for use in electronic equipment. A blank detail specification is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements shall not be considered as being in accordance with IEC specifications nor shall they so be described. This edition includes the following significant technical changes with respect to the previous edition: a) it combines IEC 60938-2-1:1999 and IEC 60938-2-2:1999 into one Blank detail specification (BDS); b) test schedule for quality conformance inspection is moved to an informative annex (Annex B).

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63203-401-1:2023(Main)
Wearable electronic devices and technologies - Part 401-1: Devices and systems: functional elements - Evaluation method of the stretchable resistive strain sensor
SIST EN IEC 63203-401-1:2024

IEC 63203-401-1:2023 specifies a measurement method of tensile strain for stretchable, resistive strain sensors. This document describes characterization procedures for evaluation of the gauge factor, linearity, response characteristics, and hysteresis of unimodal tension sensors but is not appropriate for assessment of the physical properties of the sensor material such as the elastic modulus, elastic limit, and Poisson's ratio.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60286-2:2022(Main)
Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
SIST EN IEC 60286-2:2023

IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant technical changes with respect to the previous edition: a) complete revision of structure; b) consolidation of essential parameters and requirements in Clause 4.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60286-3:2022(Main)
Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
SIST EN IEC 60286-3:2023

This part of IEC 60286 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This document also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips).

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63203-402-1:2022(Main)
Wearable electronic devices and technologies - Part 402-1: Performance measurement of fitness wearables - Test methods of glove-type motion sensors for measuring finger movements
SIST EN IEC 63203-402-1:2023

IEC 63203-402-1:2022 specifies test methods for wearable glove-type motion sensors to measure finger movements. The measurement methods include goniometric parameters related to the finger postures and flexion dynamics. Glove-type motion sensors are the type of gloves considered within the scope of this document for testing and measurement. This document describes direct and indirect measurement methods. In the direct measurement method, the angles of the joints of each finger are directly measured by a goniometer. The indirect method uses a measurement device such as a servomotor-based angle-measuring device. This document is applicable to angle measurement of all gloves with glove-type motion sensors without limitation of the device technology or size.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day