EN 61162-3:2008

SLOVENSKI STANDARD
01-november-2008
Pomorska navigacijska in radiokomunikacijska oprema in sistemi - Digitalni
vmesniki - 3. del: Instrumentno omrežje s serijskimi podatki (IEC 61162-3:2008)
Maritime navigation and radiocommunication equipment and systems - Digital interfaces
-- Part 3: Serial data instrument network
Navigations- und Funkkommunikationsgeräte und -systeme für die Seeschifffahrt -
Digitale Schnittstellen - Teil 3: Serielles Dateninstrumentenetz
Matériels et systèmes de navigation et de radiocommunication maritimes - Interfaces
numériques - Partie 3: Réseau par liaison de données série d'instruments
Ta slovenski standard je istoveten z: EN 61162-3:2008
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61162-3
NORME EUROPÉENNE
September 2008
EUROPÄISCHE NORM
ICS 47.020.70
English version
Maritime navigation and radiocommunication equipment and systems -
Digital interfaces -
Part 3: Serial data instrument network
(IEC 61162-3:2008)
Matériels et systèmes de navigation  Navigations- und
et de radiocommunication maritimes - Funkkommunikationsgeräte und -systeme
Interfaces numériques - für die Seeschifffahrt -
Partie 3: Réseau par liaison de données Digitale Schnittstellen -
série d'instruments Teil 3: Serielles Dateninstrumentenetz
(CEI 61162-3:2008) (IEC 61162-3:2008)

This European Standard was approved by CENELEC on 2008-06-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in two official versions (English and German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61162-3:2008 E
Foreword
The text of document 80/496/CDV, future edition 1 of IEC 61162-3, prepared by IEC TC 80, Maritime
navigation and radiocommunication equipment and systems, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 61162-3 on 2008-06-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-03-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-06-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61162-3:2008 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61162-3:2008
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

1) 2)
IEC 60945 - Maritime navigation and radiocommunication EN 60945 2002
equipment and systems - General
requirements - Methods of testing and
required test results
ISO 11783 Series Tractors and machinery for agriculture and - -
forestry - Serial control and communications
data network
1)
ISO 11783-3 - Tractors and machinery for agriculture and - -
forestry - Serial control and communications
data network -
Part 3: Data link layer
ISO 11783-5 2001 Tractors and machinery for agriculture and - -
+ corr. 1 2002 forestry - Serial control and communications
data network -
Part 5: Network management
NMEA 2000 2004 Serial-Data Networking of Marine Electronic - -
Main document, Devices
Version 1.200
NMEA 2000, 2004 Serial-Data Networking of Marine Electronic - -
Appendix A, Devices - Application Layer (Parameter Group
Version 1.200 Definitions)
NMEA 2000, 2006 Serial-Data Networking of Marine Electronic - -
Appendix B, Devices - Data Base
Version 1.210
NMEA 2000, 2004 Serial-Data Networking of Marine Electronic - -
Appendix C, Devices - Certification Criteria and Test
Version 1.200 Methods
NMEA 2000, 2004 Serial-Data Networking of Marine Electronic - -
Appendix D, Devices - Application Notes
Version 1.200
IMO 1974 International Convention for the Safety of Life - -
amended at Sea (SOLAS) -
Chapter V: Safety of navigation

1)
Undated reference.
2)
Valid edition at date of issue.

IEC 61162-3
Edition 1.0 2008-05
INTERNATIONAL
STANDARD
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
Q
ICS 47.020.70 ISBN 2-8318-9811-0

– 2 – 61162-3 © IEC:2008(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms, definitions and conventions.7
3.1 Terms and definitions .7
3.2 Conventions .10
4 Physical layer.10
4.1 CAN transceiver .10
4.2 Environmental .10
4.3 Radio frequency interference.10
4.3.1 Unwanted electromagnetic emissions .10
4.3.2 Immunity to electromagnetic environment .10
4.4 Cables.10
4.5 Interface power .11
4.6 Network power source.11
5 Data link layer .11
6 Network layer .11
7 Network management.11
7.1 Address configuration method .11
7.2 Address retention .11
8 Application layer.11
8.1 Parameter groups.11
8.1.1 Parameter group priority.11
8.1.2 Parameter group broadcast rate .12
9 Test criteria .12
10 Application notes.12
11 Manufacturer’s documentation.12
Annex A (informative) System integration .13

Figure A.1 – Example of configuration .
Figure A.2 – Example of configuration .15

Table A.1 – Test characteristics.14

61162-3 © IEC:2008(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61162-3 has been prepared by IEC technical committee 80:
Maritime navigation and radiocommunication equipment and systems.
The text of this standard is based on the following documents:
CDV Report on voting
80/496/CDV 80/526/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – 61162-3 © IEC:2008(E)
A list of all parts of the IEC 61162 series, under the general title M
...