EN 14758-1:2012
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non- pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to PP-MD pipes with or without an integral socket.
NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
Diese Europäische Norm legt für Rohrleitungssysteme aus mineralverstärktem Polypropylen (PP MD) Anforderungen an Vollwandrohre, Formstücke und das Rohrleitungssystem für Abwasserkanäle und leitungen fest, die in erdverlegten Schwerkraftentwässerungssystemen außerhalb der Gebäudestruktur (Anwendungskennzeichen "U") und sowohl innerhalb (Anwendungskennzeichen "D") als auch außerhalb der Gebäudestruktur eingesetzt werden.
Die Wahl des Anwendungsgebietes wird durch die Kennzeichnung der Erzeugnisse mit "U" bzw. "UD" angezeigt.
Sie legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Europäischen Norm verwiesen wird.
Diese Europäische Norm enthält eine Reihe von Nennweiten sowie Rohrreihen/Steifigkeitsklassen und gibt Empfehlungen hinsichtlich der Einfärbung.
ANMERKUNG 1 Der Anwender oder Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken für die zutreffende Auswahl dieser Kriterien verantwortlich.
Zusammen mit Teil 2 und Teil 3 der EN 14758 (siehe Vorwort) gilt dieser Teil für Rohre und Formstücke aus PP MD, für deren Verbindungen mit elastomeren Dichtringen sowie für Verbindungen mit Rohrleitungsteilen aus anderen Kunststoffen oder aus nicht aus Kunststoffen bestehenden Rohrwerkstoffen, die für erdverlegte drucklose Abwasserkanäle und leitungen vorgesehen sind.
Diese Europäische Norm ist für Rohre aus PP MD sowohl mit als auch ohne angeformte Muffe anwendbar.
ANMERKUNG 2 Die Formstücke können im Spritzgießverfahren oder aus Rohren und/oder aus Spritzgussteilen hergestellt sein.
ANMERKUNG 3 Anforderungen und Grenzwerte für Anwendungsgebiete mit Anwendungskennzeichen "D" sind in Tabelle 4, Tabelle 7 und Tabelle 13 aufgeführt.
ANMERKUNG 4 Rohre, Formstücke oder andere Rohrleitungsteile, die einer der in Anhang B aufgeführten Produktnormen für Kunststoffprodukte entsprechen, können mit Rohren und Formstücken nach dieser Europäischen Norm verwendet werden, sofern sie die Anforderungen an die Maße der Verbindungen nach Abschnitt 6 sowie die Anforderungen nach Tabelle 13 erfüllen.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1: Spécifications pour les tubes, les raccords et le système
La présente Norme européenne spécifie les exigences pour les tubes, les raccords et le système de
canalisations à paroi compacte, fabriqués à partir de polypropylène avec modificateurs minéraux (PP-MD) et
destinés à être utilisés pour les branchements et les collecteurs d’assainissement enterrés sans pression à
l’extérieur de la structure du bâtiment (code de zone d’application « U »), et pour les branchements et les
collecteurs d’assainissement enterrés sans pression aussi bien à l’intérieur de la structure du bâtiment (code
de zone d’application « D ») qu’à l’extérieur de celle-ci.
Ces informations sont précisées dans le marquage des produits par les lettres « U » et « UD ».
Elle spécifie également les paramètres d’essai pour les méthodes d’essai référencées dans cette Norme
européenne.
La présente Norme européenne couvre une gamme de dimensions nominales, une gamme de séries de
tubes/classes de rigidité et donne des recommandations concernant les couleurs.
NOTE 1 Il est de la responsabilité de l’acheteur ou du prescripteur d’effectuer les choix appropriés à partir de ces
données, en tenant compte des exigences particulières et de toute réglementation nationale applicable ainsi que des
pratiques ou codes de pose.
En relation avec la Partie 2 et la Partie 3 de l’EN 14758 (voir l’Avant-propos), elle s’applique aux tubes et aux
raccords en PP-MD, à leurs assemblages à bague d’étanchéité en élastomère et aux assemblages avec des
composants en matières plastiques et non plastiques différentes destinés à être utilisés dans les systèmes de
canalisations enterrés pour les branchements et l’assainissement sans pression.
La présente Norme européenne est applicable aux tubes PP-MD avec et sans emboîtures.
NOTE 2 Les raccords peuvent être fabriqués par moulage par injection ou être façonnés à partir de tubes et/ou de
pièces moulées.
NOTE 3 Les exigences et les valeurs limites pour le code de zone d’application « D » sont données dans le Tableau 4,
le Tableau 7 et le Tableau 13.
NOTE 4 Les tubes, les raccords et autres composants conformes à l’une des normes de produits plastiques
énumérées dans l’Annexe B peuvent être utilisés avec des tubes et des raccords conformes à cette Norme
européenne dans la mesure où ils satisfont aux exigences relatives aux dimensions d’assemblages données
dans l’Article 6 et aux exigences du Tableau 13.
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 1. del: Specifikacije za cevi, fitinge in cevni sistem
Ta evropski standard določa zahteve za trde cevi, fitinge in cevne sisteme iz polipropilena z mineralnimi modifikatorji (PP-MD) na področju sistemov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo zunaj stavbe (koda območja uporabe »U«), ter sistemov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo, za vkopane sisteme v stavbi (koda območja uporabe »D«) in zunaj stavbe.
To je razvidno iz oznak »U« in »UD« na izdelkih.
Določa tudi preskusne parametre za preskusne metode iz tega evropskega standarda.
Ta evropski standard zajema različne nazivne velikosti, več sklopov cevi/razredov togosti in vsebuje priporočila o barvah.
OPOMBA 1: Za ustrezno izbiro med temi vidiki je odgovoren kupec ali specifikator, pri čemer mora upoštevati konkretne zahteve ter vse pomembne nacionalne predpise in prakse ali kodekse vgradnje.
Skupaj z 2. in 3. delom standarda EN 14758 (glejte Predgovor) se uporablja za cevi in fitinge iz polipropilena z mineralnimi modifikatorji, njihove elastomerne tesnilne obroče in spoje s komponentami iz drugih polimernih in nepolimernih materialov, namenjenih uporabi za vkopane cevne sisteme za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo.
Ta evropski standard se uporablja za cevi iz polipropilena z mineralnimi modifikatorji z oglavki ali brez njih.
OPOMBA 2: Fitingi se lahko proizvedejo z injekcijskim brizganjem ali so izdelani iz cevi in/ali oblikovancev.
OPOMBA 3: Zahteve in mejne vrednosti za uporabo kode območja uporabe »D« so navedene v preglednicah 4, 7 in 13.
OPOMBA 4: Cevi, fitingi in drugi sestavni deli, ki so skladni s katerim koli standardom za izdelek iz polimernih materialov iz dodatka B, se lahko uporabljajo s cevmi in fitingi, ki so skladni s tem evropskim standardom, če izpolnjujejo zahteve v zvezi z velikostmi spojev iz točke 6 in zahteve iz preglednice 13.
General Information
- Status
- Withdrawn
- Publication Date
- 06-Mar-2012
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- CEN/TC 155 - Plastics piping systems and ducting systems
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 05-Apr-2023
- Completion Date
- 28-Jan-2026
Relations
- Effective Date
- 12-Jun-2010
- Effective Date
- 17-Jun-2020
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Frequently Asked Questions
EN 14758-1:2012 is a standard published by the European Committee for Standardization (CEN). Its full title is "Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system". This standard covers: This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non- pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD". It also specifies the test parameters for the test methods referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This European Standard is applicable to PP-MD pipes with or without an integral socket. NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13. NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.
This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non- pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD". It also specifies the test parameters for the test methods referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This European Standard is applicable to PP-MD pipes with or without an integral socket. NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13. NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.
EN 14758-1:2012 is classified under the following ICS (International Classification for Standards) categories: 23.040.01 - Pipeline components and pipelines in general; 93.030 - External sewage systems. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 14758-1:2012 has the following relationships with other standards: It is inter standard links to EN 14758-1:2005+A1:2009, EN 14758-1:2023, EN ISO 1043-1:2011, EN ISO 9969:2016, EN ISO 3126:2005, EN ISO 1167-4:2007, EN ISO 472:2001, EN ISO 1167-1:2006, EN ISO 1167-3:2007, EN 681-1:1996, EN ISO 1133:2005, EN ISO 580:2005, EN ISO 1167-2:2006, EN ISO 13968:2008, EN 681-2:2000. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 14758-1:2012 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 1. del: Specifikacije za cevi, fitinge in cevni sistemKunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das RohrleitungssystemSystèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1: Spécifications pour les tubes, les raccords et le systèmePlastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 14758-1:2012SIST EN 14758-1:2012en,fr,de01-maj-2012SIST EN 14758-1:2012SLOVENSKI
STANDARDSIST EN 14758-1:2006+A1:20091DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14758-1
March 2012 ICS 23.040.01 Supersedes EN 14758-1:2005+A1:2009English Version
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) -Part 1: Specifications for pipes, fittings and the system
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1: Spécifications pour les tubes, les raccords et le système
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem This European Standard was approved by CEN on 22 January 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14758-1:2012: ESIST EN 14758-1:2012
General characteristics of PP-MD pipes and fittings . 31 A.1 General . 31 A.2 Material characteristics . 31 A.3 Ring stiffness . 31 A.4 Chemical resistance . 32 SIST EN 14758-1:2012
Standards for pipes and fittings of a material other than PP-MD . 33 Bibliography . 34
Specifications for pipes, fittings and the system
Part 2:
Guidance for the assessment of conformity (published as CEN/Technical Specification) Part 3:
Guidance for installation (published as CEN/Technical Specification). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 14758-1:2012
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2,
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN ISO 472:2001,
Plastics — Vocabulary (ISO 472:1999) EN ISO 580:2005, Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) EN ISO 1043-1:2001,
Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 1133:2005,
Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) EN ISO 1167 (all parts), Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure SIST EN 14758-1:2012
Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126) EN ISO 13967,
Thermoplastics fittings — Determination of ring stiffness (ISO 13967) EN ISO 13968, Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility (ISO 13968) EN ISO 9969, Thermoplastics pipes — Determination of ring stiffness(ISO 9969) ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method ISO 11173, Thermoplastics pipes — Determination of resistance to external blows — Staircase method ISO 13257, Thermoplastics piping systems for non-pressure applications — Test method for resistance to elevated temperature cycling ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test method for leaktightness of elastomeric sealing ring type joints ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for impact strength ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for mechanical strength or flexibility of fabricated fittings 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this European Standard, the terms, definitions and symbols given in EN ISO 472:2001 and EN ISO 1043-1:2001 and the following apply. 3.1.1 application area code code used in the marking of pipes and fittings to indicate the application area for which they are intended, as follows: U:
code for the area more than 1 m from the building to which the buried piping system is connected; D:
code for the area under and within 1 m from the building where the pipes and the fittings are buried in ground and are connected to the soil and waste discharge system of the building Note 1 to entry: In code D application areas, the existence of hot water discharge in addition to the external forces from the surroundings is usual. 3.1.2 Geometrical definitions 3.1.2.1 nominal size DN numerical designation of the size of a component, which is a convenient round number approximately equal to the manufacturing dimension, in millimetres SIST EN 14758-1:2012
In case of a change in direction (e.g. in case of a bend or the service pipe of a branch), it is the length from one end to the intersection of the straight axis of this end with the straight axis of the other end of the fitting, excluding any spigot or socket length (see the dimensions Z1 and Z2 in e.g. Figures 7 and 11) 3.1.3 Material definitions 3.1.3.1 virgin material material in a form such as granules or powder that has not been subjected to use or processing other than that required for its manufacture and to which no reprocessable or recyclable material has been added 3.1.3.2 mineral modified material (PP-MD) material to which has been added minerals during specific processing operation(s) which during such processing is well distributed in the material 3.1.3.3 mean particle size D50 diameter which 50 % by mass of the particles of a mineral modifier is smaller than 3.1.3.4 particle top cut D98 diameter which 98 % by mass of the particles of a mineral modifier is smaller than 3.1.3.5 own reprocessable material material prepared from rejected unused pipes or fittings including trimmings from the production of pipes or fittings, that will be reprocessed in a manufacturer's plant after having been previously processed by the same manufacturer by a process such as moulding or extrusion, and for which the complete formulation is known 3.1.3.6 external reprocessable material material comprising either one of the following forms: a) material from rejected unused pipes or fittings or trimmings there from, that will be reprocessed and that were originally processed by another manufacturer; b) material from the production of unused products other than pipes and fittings, regardless of where they are manufactured 3.1.3.7 recyclable material material comprising either one of the following forms: a) material from used pipes or fittings which have been cleaned and crushed or ground; SIST EN 14758-1:2012
magnesium carbonate Mg3Si4O10(OH)2 magnesium silicate PP polypropylene PP-MD mineral modified polypropylene SIST EN 14758-1:2012
230 °C and loading mass 2,16 kg 4.4 Mineral modifiers 4.4.1 Types of mineral modifiers The mineral modifiers shall be of following types: coated calcium carbonate, CaCO3 or talc. When it is calcium carbonate following apply: content of CaCO3 ≥ 96 % by mass; content of MgCO3
≤ 4 % by mass; content of CaCO3 and MgCO3 in total ≥ 98 % by mass. When it is talc following apply: content of magnesium silicate (Mg3Si4O10(OH)2) ≥ 97 % by mass. NOTE The addition of mineral modifiers is an effective way of increasing the E-modulus of the base polypropylene material. SIST EN 14758-1:2012
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...