EN ISO 16484-5:2003
(Main)Building automation and control systems - Part 5: Data communication protocolcity (ISO 16484-5:2003)
Building automation and control systems - Part 5: Data communication protocolcity (ISO 16484-5:2003)
This protocol provides a comprehensive set of messages for conveying encoded binary, analog, and alphanumeric data between devices including, but notlimited to: (a) hardware binary input and output values, (b) hardware analog input and output values, (c) sofware binary and analog values, (d) text string values, (e) schedule information, (f) alarm and event information, (g) files, and (h) control logic.
Systeme der Gebäudeautomation - Teil 5: Datenkommunikationsprotokoll (ISO 16484-5:2003)
Systèmes d'automatisation et de gestion technique du bâtiment - Partie 5: Protocole de communication de données (ISO 16484-5:2003)
Avtomatizacija stavb in sistemi za regulacijo – 5. del: Protokol izmenjave podatkov (ISO 16484-5:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16484-5:2004
01-februar-2004
Avtomatizacija stavb in sistemi za regulacijo – 5. del: Protokol izmenjave podatkov
(ISO 16484-5:2003)
Building automation and control systems - Part 5: Data communication protocolcity (ISO
16484-5:2003)
Systeme der Gebäudeautomation - Teil 5: Datenkommunikationsprotokoll (ISO 16484-
5:2003)
Systemes d'automatisation et de gestion technique du bâtiment - Partie 5: Protocole de
communication de données (ISO 16484-5:2003)
Ta slovenski standard je istoveten z: EN ISO 16484-5:2003
ICS:
35.240.99
97.120
SIST EN ISO 16484-5:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 16484-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2003
ICS 35.240.99; 91.040.01 Supersedes ENV 1805-1:1998
English version
Building automation and control systems - Part 5: Data
communication protocolcity (ISO 16484-5:2003)
Systèmes d'automatisation et de gestion technique du Systeme der Gebäudeautomation - Teil 5:
bâtiment - Partie 5: Protocole de communication de Datenkommunikationsprotokoll (ISO 16484-5:2003)
données (ISO 16484-5:2003)
This European Standard was approved by CEN on 14 October 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16484-5:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 16484-5:2003 (E)
Foreword
This document (EN ISO 16484-5:2003) has been prepared by Technical Committee ISO/TC 205
"Building environment design" in collaboration with Technical Committee CEN/TC 247 "Building
Automation, Controls and Building Management", the secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2004, and conflicting national standards
shall be withdrawn at the latest by May 2004.
This document supersedes ENV 1805-1:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
NOTE FROM CMC The foreword is susceptible to be amended on reception of the German
language version. The confirmed or amended foreword, and when appropriate, the normative
annex ZA for the references to international publications with their relevant European
publications will be circulated with the German version.
Endorsement notice
The text of ISO 16484-5:2003 has been approved by CEN as EN ISO 16484-5:2003 without any
modifications.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 16484-5
First edition
2003-11-01
Building automation and control
systems —
Part 5:
Data communication protocol
Systèmes d'automatisation et de gestion technique du bâtiment —
Partie 5: Protocole de communication de données
Reference number
ISO 16484-5:2003(E)
©
ISO 2003
---------------------- Page: 4 ----------------------
ISO 16484-5:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 5 ----------------------
ISO 16484-5:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16484-5 was prepared by the American Society of Heating, Refrigerating and Air-Conditioning Engineers
(ASHRAE) (as ANSI/ASHRAE 135-2001) and was adopted without modifications by Technical Committee
ISO/TC 205, Building environment design.
ISO 16484 consists of the following parts, under the general title Building automation and control systems:
Part 1: Overview and definitions
Part 2: Hardware
Part 3: Functions
Part 5: Data communication protocol
Further parts are under preparation.
© ISO 2003 — All rights reserved iii
---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO 16484-5:2003(E)
Building automation and control systems —
Part 5:
Data communication protocol
1 Scope
This part of ISO 16484 defines data communication services and protocols for computer equipment used for
monitoring and control of heating, ventilation, air-conditioning and refrigeration (HVAC&R) and other building
systems. It defines, in addition, an abstract, object-oriented representation of information communicated
between such equipment, thereby facilitating the application and use of digital control technology in buildings.
The scope and field of application are furthermore detailed in Clause 2 of the enclosed ANSI/ASHRAE
publication.
2 Requirements
Requirements are the technical recommendations made in the following publication (reproduced on the
following pages), which is adopted as an International Standard:
ANSI/ASHRAE 135-2001, A Data Communication Protocol for Building Automation and Control Networks
The text on the back of the title page of the ANSI/ASHRAE standard and the policy statement on the last page
are not relevant for the purposes of international standardization.
International Standards cited in the text are the following:
ISO/IEC 7498 (all parts), Information technology — Open Systems Interconnection — Basic Reference
Model
ISO/TR 8509, Information processing systems — Open Systems Interconnection — Service conventions
ISO/IEC 8802-2, Information technology — Telecommunications and information exchange between
systems — Local and metropolitan area networks — Specific requirements — Part 2: Logical link control
ISO/IEC 8824 (all parts), Information technology — Abstract Syntax Notation One (ASN.1): Specification
of basic notation
3 Revision of ANSI/ASHRAE 135
It has been agreed with the American Society of Heating, Refrigerating and Air-Conditioning Engineers
(ASHRAE) that TechnicalCommittee ISO/TC 205 will be consulted in the event of any revision or amendment
of ANSI/ASHRAE 135. To this end, ANSI will act as a liaison body between ASHRAE and ISO.
© ISO 2003 — All rights reserved 1
---------------------- Page: 7 ----------------------
ISO 16484-5:2003(E)
(Blank page)
2 © ISO 2003 — All rights reserved
---------------------- Page: 8 ----------------------
ISO 16484-5:2003(E)
ANSI/ASHRAE Standard 135-2001
(Including ANSI/ASHRAE Addenda listed in the History of Revisions)
A Data Communication
Protocol for Building
Automation and
Control Networks
Approved by the ASHRAE Standards Committee June 23, 2001; by
the ASHRAE Board of Directors June 28, 2001; and by the Ameri-
can National Standards Institute September 7, 2001. See “History
of Revisions” section for approval dates of addenda.
This standard is under continuous maintenance by a Standing
Standard Project Committee (SSPC) for which the Standards Com-
mittee has established a documented program for regular publi-
cation of addenda or revisions, including procedures for timely,
documented, consensus action on requests for change to any
part of the standard. The change submittal form, instructions, and
deadlines are given at the back of this document and may be
obtained in electronic form from ASHRAE’s Internet Home Page,
http://www.ashrae.org, or in paper form from the Manager of Stan-
dards. The latest edition of an ASHRAE Standard and printed cop-
ies of a public review draft may be purchased from ASHRAE Cus-
tomer Service, 1791 Tullie Circle, NE, Atlanta, GA 30329-2305. E-
mail: orders@ashrae.org. Fax: 404-321-5478. Telephone: 404-636-
8400 (worldwide), or toll free 1-800-527-4723 (for orders in U.S. and
Canada).
©Copyright 2001 American Society of Heating,
Refrigerating and Air-Conditioning Engineers, Inc.
ISSN 1041-2336
AMERICAN SOCIETY OF HEATING,
REFRIGERATING AND
AIR-CONDITIONING ENGINEERS, INC.
1791 Tullie Circle, NE Atlanta, GA 30329
© ISO 2003 – All rights reserved 3
---------------------- Page: 9 ----------------------
ISO 16484-5:2003(E)
ASHRAE STANDING STANDARD PROJECT COMMITTEE 135
Cognizant TC: TC 1.4, Control Theory and Applications
SPLS Liaison: Ronald E. Jarnagin
Steven T. Bushby, Chair* Dana R. Epperson Jerald P. Martocci*
William O. Swan III, Vice-Chair Thomas S. Ertsgaard* Carl Neilson*
Keith A. Corbett, Secretary* David M. Fisher H. Michael Newman
Ron E. Anderson Daniel P. Giorgis* Cherisse M. Nicastro
Beauford W. Atwater Ira G. Goldschmidt Robert L. Old, Jr.
David J. Branson Jerald Griliches Mark A. Railsback*
Barry B. Bridges* John L. Hartman David Robin*
James F. Butler Winston I. Hetherington Patrick Sheridan
A. J. Capowski* Richard Holtz Kevin G. Sweeney
Jeffery Cosiol* Anthony J. Icenhour Daniel A. Traill*
Harsha M. Dabholkar Stephen Karg* Grant N. Wichenko*
J. D. Ljungquist* Robert J. Zamojcin
*Denotes members of voting status when this standard was approved for publication.
__________________________________________________________________________________________________________________
ASHRAE STANDARDS COMMITTEE 2000-2001
Martha J. Hewett, Chairman David E. Knebel Steven T. Taylor
Nance C. Lovvorn, Vice-Chairman Frederick H. Kohloss James K. Vallort
Van D. Baxter William J. Landman Thomas E. Watson
Dean S. Borges Rodney H. Lewis Bruce A. Wilcox
Waller S. Clements Ross D. Montgomery J. Richard Wright
Piotr A. Domanski Davor Novosel Gerald C. Groff, BOD ExO
Richard A. Evans Joseph A. Pietsch William J. Buck, CO
John F. Hogan James A. Ranfone
Ronald E. Jarnagin Michael Tavares
Claire B. Ramspeck, Manager of Standards
__________________________________________________________________________________________________________________
SPECIAL NOTE
This American National Standard (ANS) is a national voluntary consensus standard developed under the auspices of the American Society of Heating,
Refrigerating and Air-Conditioning Engineers (ASHRAE). Consensus is defined by the American National Standards Institute (ANSI), of which ASHRAE is a
member and which has approved this standard as an ANS, as “substantial agreement reached by directly and materially affected interest categories. This signifies
the concurrence of more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that an effort
be made toward their resolution." Compliance with this standard is voluntary until and unless a legal jurisdiction makes compliance mandatory through
legislation.
ASHRAE obtains consensus through participation of its national and international members, associated societies, and public review.
ASHRAE Standards are prepared by a Project Committee appointed specifically for the purpose of writing the Standard. The Project Committee Chair and Vice-
Chair must be members of ASHRAE; while other members may or may not be members of ASHRAE, all must be technically qualified in the subject area of the
standard. Every effort is made to balance the concerned interests on all Project Committees.
The Manager of Standards of ASHRAE should be contacted for:
a. interpretation of the contents of this Standard,
b. participation in the next review of the Standard,
c. offering constructive criticism for improving the Standard,
d. permission to reprint portions of the Standard.
DISCLAIMER
ASHRAE uses its best efforts to promulgate standards for the benefit of the public in light of available information and accepted industry practices. However,
ASHRAE does not guarantee, certify, or assure the safety or performance of any products, components, or systems tested, designed, installed, or operated in
accordance with ASHRAE’s Standards or Guidelines or that any tests conducted under its standards will be nonhazardous or free from risk.
ASHRAE INDUSTRIAL ADVERTISING POLICY ON STANDARDS
ASHRAE Standards and Guidelines are established to assist industry and the public by offering a uniform method of testing for rating purposes, by
suggesting safe practices in designing and installing equipment, by providing proper definitions of this equipment, and by providing other information that
may serve to guide the industry. The creation of ASHRAE Standards and Guidelines is determined by the need for them, and conformance to them is
completely voluntary.
In referring to this standard and marking of equipment and in advertising, no claim shall be made, either stated or implied, that the product has been approved
by ASHRAE.
4 © ISO 2003 – All rights reserved
---------------------- Page: 10 ----------------------
ISO 16484-5:2003(E)
CONTENTS
FOREWORD ………………………………………………………………………………………………………………….vii
1 PURPOSE.1
2 SCOPE.1
3 DEFINITIONS .1
3.1 Terms Adopted from International Standards.1
3.2 Terms Defined for this Standard.2
3.3 Abbreviations and Acronyms Used in this Standard .5
4 BACnet PROTOCOL ARCHITECTURE.8
4.1 The BACnet Collapsed Architecture .9
4.2 BACnet Network Topology.11
4.3 Security.13
5 THE APPLICATION LAYER .14
5.1 The Application Layer Model.14
5.2 Segmentation of BACnet Messages .18
5.3 Transmission of BACnet APDUs.19
5.4 Application Protocol State Machines.23
5.5 Application Protocol Time Sequence Diagrams.37
5.6 Application Layer Service Conventions .45
6 THE NETWORK LAYER .47
6.1 Network Layer Service Specification .47
6.2 Network Layer PDU Structure .48
6.3 Messages for Multiple Recipients.53
6.4 Network Layer Protocol Messages .54
6.5 Network Layer Procedures .56
6.6 BACnet Routers.58
6.7 Point-To-Point Half-Routers.63
7 DATA LINK/PHYSICAL LAYERS: ISO 8802-3 ("Ethernet") LAN.68
7.1 The Use of ISO 8802-2 Logical Link Control (LLC).68
7.2 Parameters Required by the LLC Primitives .68
7.3 Parameters Required by the MAC Primitives.68
7.4 Physical Media .68
8 DATA LINK/PHYSICAL LAYERS: ARCNET LAN.70
8.1 The Use of ISO 8802-2 Logical Link Control (LLC).70
8.2 Parameters Required by the LLC Primitives .70
8.3 Mapping the LLC Services to the ARCNET MAC Layer.70
8.4 Parameters Required by the MAC Primitives.70
8.5 Physical Media .70
9 DATA LINK/PHYSICAL LAYERS: MASTER-SLAVE/TOKEN PASSING (MS/TP) LAN .72
9.1 Service Specification .72
9.2 Physical Layer .74
9.3 MS/TP Frame Format.76
9.4 Overview of the MS/TP Network.77
9.5 MS/TP Medium Access Control.78
9.6 Cyclic Redundancy Check (CRC) .94
9.7 Interfacing MS/TP LANs with Other BACnet LANs.95
9.8 Responding BACnet User Processing of Messages from MS/TP.95
9.9 Repeaters .95
10 DATA LINK/PHYSICAL LAYERS: POINT-TO-POINT (PTP).97
10.1 Overview .97
10.2 Service Specification .97
10.3 Point-to-Point Frame Format.102
10.4 PTP Medium Access Control Protocol.104
11 DATA LINK/PHYSICAL LAYERS: EIA/CEA-709.1 ("LonTalk") LAN .125
11.1 The Use of ISO 8802-2 Logical Link Control (LLC).125
11.2 Parameters Required by the LLC Primitives .125
ASHRAE 135-2001 i
© ISO 2003 – All rights reserved 5
---------------------- Page: 11 ----------------------
ISO 16484-5:2003(E)
11.3 Mapping the LLC Services to the LonTalk Application Layer .125
11.4 Parameters Required by the Application Layer Primitives.125
11.5 Physical Media .126
12 MODELING CONTROL DEVICES AS A COLLECTION OF OBJECTS.127
12.1 Analog Input Object Type .130
12.2 Analog Output Object Type.135
12.3 Analog Value Object Type .140
12.4 Averaging Object Type.145
12.5 Binary Input Object Type .148
12.6 Binary Output Object Type.153
12.7 Binary Value Object Type .159
12.8 Calendar Object Type.164
12.9 Command Object type .166
12.10 Device Object Type .169
12.11 Event Enrollment Object Type .175
12.12 File Object Type .180
12.13 Group Object Type .182
12.14 Life Safety Point Object Type .184
12.15 Life Safety Zone Object Type .190
12.16 Loop Object Type.196
12.17 Multi-state Input Object Type.203
12.18 Multi-state Output Object Type.207
12.19 Multi-state Value Object Type .211
12.20 Notification Class Object type.216
12.21 Program Object Type.219
12.22 Schedule Object Type.224
12.23 Trend Log Object Type .227
13 ALARM AND EVENT SERVICES.233
13.1 Change of Value Reporting .234
13.2 Intrinsic Reporting.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.