Non-destructive testing - Ultrasonic examination - Specification for calibration block No. 1

This standard specifies requirements for the dimensions, material and manufacture of a steel block for calibrating ultrasonic flaw detection and inspection equipment used in manual testing. The calibration block dealt with in this standard is identified calibration block No.1 to distinguish it from other calibration blocks.

Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Kalibrierkörpers Nr 1

Diese Norm legt die Anforderungen an Abmessungen, Werkstoff und Herstellung eines Stahlkörpers bestimmter Bauart fest, der zur Justierung von Ultraschallprüfgeräten dient, die bei der Handprüfung verwendet werden. Der in dieser Norm behandelte Kalibrierkörper wird zur Unterscheidung von anderen Kalibrierkörpern "Kontrollkörper Nr 1" genannt.

Essais non destructifs - Contrôle par ultrasons - Spécifications relatives au bloc d'étalonnage n° 1

La présente norme fixe les prescriptions relatives aux dimensions, au matériau et à la fabrication de l'un des modèles de blocs d'acier qui servent à étalonner l'appareil de contrôle par ultrasons et ses équipements utilisés lors des contrôles manuels. Le bloc d'étalonnage dont il est question dans la présente norme, est appelé "bloc d'étalonnage n°1", pour le distinguer des autres blocs d'étalonnage.

Neporušitveno preskušanje - Ultrazvočne preiskave - Specifikacije za umeritveni vzorec št. 1

General Information

Status
Withdrawn
Publication Date
07-Dec-1999
Withdrawal Date
14-Sep-2012
ICS
19.100 - Non-destructive testing
Technical Committee
CEN/TC 138 - Non-destructive testing
Drafting Committee
CEN/TC 138/WG 2 - Ultrasonic testing
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
15-Sep-2012
Completion Date
15-Sep-2012
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 12223:2000 - Non-destructive testing - Ultrasonic examination - Specification for calibration block No. 1

Relations

Replaced By
EN ISO 2400:2012 - Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 1 (ISO 2400:2012)
Effective Date
08-Jun-2022
Referred By
EN ISO 5350-2:2006 - Pulps - Estimation of dirt and shives - Part 2: Inspection of mill sheeted pulp by transmitted light (ISO 5350-2:2006)
Effective Date
28-Jan-2026
Referred By
EN ISO 14453:1998 - Pulps - Determination of acetone-soluble matter (ISO 14453:1997)
Effective Date
28-Jan-2026
Referred By
EN ISO 5263-2:2004 - Pulps - Laboratory wet disintegration - Part 2: Disintegration of mechanical pulps at 20 degrees C (ISO 5263-2:2004)
Effective Date
28-Jan-2026
Referred By
EN ISO 5263-1:2004 - Pulps - Laboratory wet disintegration - Part 1: Disintegration of chemical pulps (ISO 5263-1:2004)
Effective Date
28-Jan-2026
Referred By
EN ISO 5263-3:2004 - Pulps - Laboratory wet disintegration - Part 3: Disintegration of mechanical pulps at > 85 degrees C (ISO 5263-3:2004)
Effective Date
28-Jan-2026
Referred By
EN ISO 5350-1:2006 - Pulps - Estimation of dirt and shives - Part 1: Inspection of laboratory sheets by transmitted light (ISO 5350-1:2006)
Effective Date
28-Jan-2026

Frequently Asked Questions

EN 12223:1999 is a standard published by the European Committee for Standardization (CEN). Its full title is "Non-destructive testing - Ultrasonic examination - Specification for calibration block No. 1". This standard covers: This standard specifies requirements for the dimensions, material and manufacture of a steel block for calibrating ultrasonic flaw detection and inspection equipment used in manual testing. The calibration block dealt with in this standard is identified calibration block No.1 to distinguish it from other calibration blocks.

This standard specifies requirements for the dimensions, material and manufacture of a steel block for calibrating ultrasonic flaw detection and inspection equipment used in manual testing. The calibration block dealt with in this standard is identified calibration block No.1 to distinguish it from other calibration blocks.

EN 12223:1999 is classified under the following ICS (International Classification for Standards) categories: 19.100 - Non-destructive testing. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 12223:1999 has the following relationships with other standards: It is inter standard links to EN ISO 2400:2012, EN ISO 5350-2:2006, EN ISO 14453:1998, EN ISO 5263-2:2004, EN ISO 5263-1:2004, EN ISO 5263-3:2004, EN ISO 5350-1:2006. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 12223:1999 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/071. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

EN 12223:1999 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Kalibrierkörpers Nr 1Essais non destructifs - Contrôle par ultrasons - Spécifications relatives au bloc d'étalonnage n° 1Non-destructive testing - Ultrasonic examination - Specification for calibration block No. 119.100Neporušitve
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...