EN 13260:2009/FprA1

SLOVENSKI STANDARD
01-julij-2010
äHOH]QLãNHQDSUDYH.ROHVQHGYRMLFHLQSRGVWDYQLYR]LþNL.ROHVQHGYRMLFH
=DKWHYDQHODVWQRVWLSURL]YRGD'RSROQLOR$
Railway applications - Wheelsets and bogies - Wheelsets - Product requirements
Bahnanwendungen - Radsätze und Drehgestelle - Radsätze - Produktanforderungen
Applications ferroviaires - Essieux montés et bogies - Essieux montés - Prescriptions
pour le produit
Ta slovenski standard je istoveten z: EN 13260:2009/FprA1
ICS:
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 13260:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
May 2010
ICS 45.040
English Version
Railway applications - Wheelsets and bogies - Wheelsets -
Product requirements
Applications ferroviaires - Essieux montés et bogies - Bahnanwendungen - Radsätze und Drehgestelle -
Essieux montés - Prescriptions pour le produit Radsätze - Produktanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 256.
This draft amendment A1, if approved, will modify the European Standard EN 13260:2009. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13260:2009/FprA1:2010: E
worldwide for CEN national Members.

EN 13260:2009/prA1:2010 (E)
Contents Page
Foreword.3
1 Amendment of the Foreword.4
2 Amendment of Annex ZA.4
3 Deletion of Annex ZB .7

EN 13260:2009/prA1:2010 (E)
Foreword
This document (EN 13260:2009/prA1:2010) has been prepared by Technical Committee CEN/TC 256
“Railway applications”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2008/57/EC.
For relationship with the EU Directive, see informative Annex ZA, which is an integral part of this document.
EN 13260:2009/prA1:2010 (E)
1 Amendment of the Foreword
th
Delete the 5 paragraph of the Foreword and replace with:
"This document has been prepared under a mandate given to CEN/CENELEC/ETSI by the European
Commission and the European Free Trade Association, and supports essential requirements of EU Directive
2008/57/EC."
th
Delete the 6 paragraph and replace with:
"For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of this
document."
2 Amendment of Annex ZA
Replace Annex ZA with the following Annex ZA:
"
Annex ZA
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 2008/57/EC
This European Standard has been prepared under a mandate given to CEN/CENELEC/ETSI by the European
Commission to provide a means of conforming to Essential Requirements of the New Approach Directive
2008/57/EC .
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the clauses of this
standard given in Table ZA.1 for High Speed Rolling Stock, Table ZA.2 for Freight Wagons and Table ZA.3 for
Locomotives and Passenger Rolling Stock, co
...