EN ISO 60:2023

SLOVENSKI STANDARD
01-december-2023
Polimerni materiali - Določanje nasipne mase materiala, ki se lahko nasipa skozi lij
določenih mer (ISO 60:2023)
Plastics - Determination of apparent density of material that can be poured from a
specified funnel (ISO 60:2023)
Kunststoffe - Bestimmung der scheinbaren Dichte von Formmassen, die durch einen
genormten Trichter abfließen können (Schüttdichte) (ISO 60:2023)
Plastiques - Détermination de la masse volumique apparente des matières susceptibles
de s'écouler à travers un entonnoir donné (ISO 60:2023)
Ta slovenski standard je istoveten z: EN ISO 60:2023
ICS:
83.080.10 Duromeri Thermosetting materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 60
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2023
EUROPÄISCHE NORM
ICS 83.080.10 Supersedes EN ISO 60:1999
English Version
Plastics - Determination of apparent density of material
that can be poured from a specified funnel (ISO 60:2023)
Plastiques - Détermination de la masse volumique Kunststoffe - Bestimmung der scheinbaren Dichte von
apparente des matières susceptibles de s'écouler à Formmassen, die durch einen genormten Trichter
travers un entonnoir donné (ISO 60:2023) abfließen können (Schüttdichte) (ISO 60:2023)
This European Standard was approved by CEN on 30 September 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 60:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 60:2023) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2024, and conflicting national standards shall be
withdrawn at the latest by April 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 60:1999.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 60:2023 has been approved by CEN as EN ISO 60:2023 without any modification.

INTERNATIONAL ISO
STANDARD 60
Third edition
2023-09
Plastics — Determination of apparent
density of material that can be poured
from a specified funnel
Plastiques — Détermination de la masse volumique apparente des
matières susceptibles de s'écouler à travers un entonnoir donné
Reference number
ISO 60:2023(E)
ISO 60:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 60:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 1
5 Procedure .2
6 Expression of results . 3
7 Test report . 3
Bibliography .
...