EN ISO 12216:2022/A1:2022

SLOVENSKI STANDARD
SIST EN ISO 12216:2022/A1:2022
01-december-2022
Mala plovila - Okna, lopute, pokrovi in vrata - Zahteve za trdnost in odpornost proti
vodi - Dopolnilo A1 (ISO 12216:2020/Amd 1:2022)
Small craft - Windows, portlights, hatches, deadlights and doors - Strength and
watertightness requirements - Amendment 1 (ISO 12216:2020/Amd 1:2022)
Kleine Wasserfahrzeuge - Fenster, Bullaugen, Luken, Seeschlagblenden und Türen -
Anforderungen an die Festigkeit und Wasserdichtheit - Änderung 1 (ISO
12216:2020/Amd 1:2022)
Petits navires - Fenêtres, hublots, panneaux, tapes et portes - Exigences de résistance
et d'étanchéité - Amendement 1 (ISO 12216:2020/Amd 1:2022)
Ta slovenski standard je istoveten z: EN ISO 12216:2022/A1:2022
ICS:
47.080 Čolni Small craft
91.060.50 Vrata in okna Doors and windows
SIST EN ISO 12216:2022/A1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 12216:2022/A1:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 12216:2022/A1:2022


EN ISO 12216:2022/A1
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2022
EUROPÄISCHE NORM
ICS 47.080
English Version

Small craft - Windows, portlights, hatches, deadlights and
doors - Strength and watertightness requirements -
Amendment 1 (ISO 12216:2020/Amd 1:2022)
Petits navires - Fenêtres, hublots, panneaux, tapes et Kleine Wasserfahrzeuge - Fenster, Bullaugen, Luken,
portes - Exigences de résistance et d'étanchéité - Seeschlagblenden und Türen - Anforderungen an die
Amendement 1 (ISO 12216:2020/Amd 1:2022) Festigkeit und Wasserdichtheit - Änderung 1 (ISO
12216:2020/Amd 1:2022)
This amendment A1 modifies the European Standard EN ISO 12216:2022; it was approved by CEN on 2 August 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12216:2022/A1:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 12216:2022/A1:2022
EN ISO 12216:2022/A1:2022 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4

2

---------------------- Page: 4 ----------------------
SIST EN ISO 12216:2022/A1:2022
EN ISO 12216:2022/A1:2022 (E)
European foreword
This document (EN ISO 12216:2022/A1:2022) has been prepared by Technical Committee ISO/TC 188
"Small craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of
which is held by SIS.
This Amendment to the European Standard EN ISO 12216:2022 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by April 2023, and
conflicting national standards shall be withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any fee
...