Aerospace series - Holes for 100° countersunk head screws - Design standard

This standard specifies holes in common parts and sheet metal for 100° countersunk head screws with nominal diameters of 3 mm to 5 mm and head configuration according to EN standards for aerospace applications.

Luft- und Raumfahrt - Löcher für 100°-Senkschrauben - Konstruktionsnorm

Diese Norm legt die Löcher in üblichen Teilen und Blechteilen für 100° Senkschrauben mit 3 mm bis 5 mm Nenndurchmesser und Kopfausführung nach EN Normen zur Verwendung in der Luft- und Raumfahrt fest.

Série aérospatiale - Trous pour vis à tête fraisée 100° - Norme de conception

Aeronavtika - Luknje za vijake z ugrezno glavo (100°) - Standard za projektiranje

General Information

Status
Withdrawn
Publication Date
27-May-2008
Withdrawal Date
07-Nov-2023
Technical Committee
Drafting Committee
Current Stage

Buy Standard

Standard
EN 3782:2008
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2008
Aeronavtika - Luknje za vijake z ugrezno glavo (100°) - Standard za projektiranje
Aerospace series - Holes for 100° countersunk head screws - Design standard
Luft- und Raumfahrt - Löcher für 100°-Senkschrauben - Konstruktionsnorm
Série aérospatiale - Trous pour vis à tête fraisée 100° - Norme de conception
Ta slovenski standard je istoveten z: EN 3782:2008
ICS:
49.030.01 Vezni elementi na splošno Fasteners in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 3782
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2008
ICS 49.030.01
English Version
Aerospace series - Holes for 100° countersunk head screws -
Design standard
Série aérospatiale - Trous pour vis à tête fraisée 100° - Luft- und Raumfahrt - Löcher für 100° -Senkschrauben -
Norme de conception Konstruktionsnorm
This European Standard was approved by CEN on 3 November 2007.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3782:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope.4
2 Use.4
2.1 Normal application.4
2.2 Aerodynamic application.4
3 Required characteristics.4
4 Designation.6
5 Indication in drawings.6

Figures
Figure 1 — Countersunk holes in common parts . 4
Figure 2 — Countersunk holes in sheet metal . 5
Figure 3 — Indication in drawings .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.