EN ISO 5774:2023

SLOVENSKI STANDARD
01-julij-2023
Polimerne cevi - S tekstilom ojačene cevi za zrak pod tlakom - Specifikacija (ISO
5774:2023)
Plastics hoses - Textile-reinforced types for compressed-air applications - Specification
(ISO 5774:2023)
Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Anforderung
(ISO 5774:2023)
Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé -
Spécifications (ISO 5774:2023)
Ta slovenski standard je istoveten z: EN ISO 5774:2023
ICS:
83.120 Ojačani polimeri Reinforced plastics
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 5774
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2023
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 5774:2016
English Version
Plastics hoses - Textile-reinforced types for compressed-
air applications - Specification (ISO 5774:2023)
Tuyaux en plastique - Types armés de textile pour Kunststoffschläuche - Textilverstärkte Typen für
applications avec de l'air comprimé - Spécifications Druckluftanwendungen - Anforderung (ISO
(ISO 5774:2023) 5774:2023)
This European Standard was approved by CEN on 29 April 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5774:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 5774:2023) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2023, and conflicting national standards
shall be withdrawn at the latest by November 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 5774:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 5774:2023 has been approved by CEN as EN ISO 5774:2023 without any modification.

INTERNATIONAL ISO
STANDARD 5774
Fifth edition
2023-04
Plastics hoses — Textile-reinforced
types for compressed-air applications
— Specification
Tuyaux en plastique — Types armés de textile pour applications avec
de l'air comprimé — Spécifications
Reference number
ISO 5774:2023(E)
ISO 5774:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 5774:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Couplings and end fittings .2
6 Materials and construction . 2
7 Dimensions and tolerances .2
7.1 Inside diameter, tolerances and minimum wall thickness . 2
7.2 Concentricity . 3
7.3 Tolerances on length. 3
8 Physical properties .4
8.1 Plastic compounds . 4
8.1.1 Tensile strength and elongation at break of lining and cover . 4
8.1.2 Resistance to ageing . 4
8.1.3 Loss in mass on heating . 4
8.1.4 Resistance to liquids . 4
8.1.5 Hydrolysis test. 4
8.2 Performance requirements on finished hoses . 5
8.2.1 Hydrostatic requirements . 5
8.2.2 Adhesion . 5
8.2.3 Exposure to a xenon arc lamp . 5
8.2.4 Bending test . 5
8.2.5 Low-temperature flexibility. 6
9 Frequency of testing . .6
10 Marking . . 6
11 Recommendations for packaging and storage . 7
12 Test report . 7
Annex A (normative) Hydrolysis test .8
Annex B (normative) Type and routine tests .10
Annex C (informative) Production acceptance tests .11
Annex D (informative) Couplings and end fittings .12
Bibliography .13
iii
ISO 5774:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Org
...