EN 2602:2005

SLOVENSKI STANDARD
01-september-2006
$HURQDYWLND±9KRGL]DDGDSWHUMH]QDYRMHP]]DNOHSQLPREURþNRP±
*HRPHWULMVNLQDþUW
Aerospace series - Ports for adaptors, threaded, with lockring - Geometric configuration
Luft- und Raumfahrt - Einschraublöcher für gerade Einschraubverschraubungen mit
Sicherungsring - Konstruktionsblatt
Série aérospatiale - Orifices pour raccords droits, filetés, avec bague de sécurité -
Configuration géométrique
Ta slovenski standard je istoveten z: EN 2602:2005
ICS:
49.030.99
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 2602
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 49.030.99
English Version
Aerospace series - Ports for adaptors, threaded, with lockring -
Geometric configuration
Série aérospatiale - Implantation des raccords droits Luft- und Raumfahrt - Einschraublöcher für gerade
métriques avec bague de sécurité - Dimensions Einschraubverschraubungen mit Sicherungsring -
Konstruktionsblatt
This European Standard was approved by CEN on 28 October 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2602:2005: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Required characteristics .5
4 Designation .8

Foreword
This European Standard (EN 2602:2005) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-
ceived the approval of the National Associations and the Official Services of the member countries of AECMA,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the
latest by June 2006.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den-
mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem-
bourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the
United Kingdom.
1 Scope
This standard specifies the dimensional characteristics of ports for the adaptors, threaded, with lockring,
assembly with elastomer O-ring, for aerospace applications.
This standard applies to all adaptors with lockring whose port end is define
...