EN 1009-4:2020

SLOVENSKI STANDARD
01-september-2020
Stroji za mehansko obdelavo mineralov in podobnih trdnih snovi - Varnost - 4. del:
Posebne zahteve za presejalne stroje
Machines for mechanical processing of minerals and similar solid materials - Safety -
Part 4: Specific requirements for screening machinery
Maschinen für die mechanische Aufbereitung von Mineralien und ähnlichen festen
Stoffen - Sicherheit - Teil 4: Spezifische Anforderungen für Klassiermaschinen
(Siebmaschinen)
Machines pour le traitement mécanique des minéraux et des matériaux solides similaires
- Sécurité - Partie 4 : Prescriptions spécifiques pour machines de criblage
Ta slovenski standard je istoveten z: EN 1009-4:2020
ICS:
13.110 Varnost strojev Safety of machinery
73.120 Oprema za predelavo rudnin Equipment for processing of
minerals
91.220 Gradbena oprema Construction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 1009-4
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 73.120; 91.220
English Version
Machines for mechanical processing of minerals and
similar solid materials - Safety - Part 4: Specific
requirements for screening machinery
Machines pour le traitement mécanique des minéraux Maschinen für die mechanische Aufbereitung von
et des matériaux solides similaires - Sécurité - Partie 4 : Mineralien und ähnlichen festen Stoffen - Sicherheit -
Prescriptions spécifiques pour machines de criblage Teil 4: Spezifische Anforderungen für
Klassiermaschinen (Siebmaschinen)
This European Standard was approved by CEN on 13 April 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1009-4:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Safety requirements and/or protective/risk reduction measures . 7
4.1 General . 7
4.2 Ergonomics requirements for screening machines maintenance . 8
4.3 Screen equipment (cross tensioned screening panels, sheets, blocks and other wear
parts) . 20
5 Verification of safety requirements and/or protective/risk reduction measures . 21
6 Information for use . 23
6.1 General . 23
6.2 Signals and warning devices . 23
6.3 Instruction handbook . 23
Annex A (informative) Example of screening machinery . 24
Annex B (informative) Trilingual terminology of screening machinery. 27
Annex C (informative) Calculation of the access dimensions . 28
Annex D (informative) List of significant hazards . 31
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC aimed to be covered . 35
Bibliography . 37

European foreword
This document (EN 1009-4:2020) has been prepared by Technical Committee CEN/TC 151 “Construction
equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards shall
be withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
This part of EN 1009 is intended to be used in conjunction with EN 1009-1:2020.
EN 1009 “Machines for mechanical processing of minerals and similar solid materials — Safety”
comprises the following parts:
— Part 1: Common requirements for machinery and processing plants
— Part 2: Specific requirements for feeding machinery and continuous handling equipment
— Part 3: Specific requirements for crushing and milling machinery
— Part 4: Specific requirements for screening machinery
— Part 5: Specific requirements for cleaning, recycling and mud treatment machinery
— Part 6: Specific requirements for mobile machinery (in preparation)
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
This document is a type-C standard as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
1 Scope
This document, to be used together with EN 1009-1:2020, specifies the safety requirements and their
verification for the design and construction of screening machinery for the mechanical processing in
quarrying, recycling and processing mineral and by-products as defined in 3.1.
In addition, it specifies the type of information on safe working practices (including residual risks) to be
provided by the manufacturer.
When requirements of this document are different from those which are stated in EN 1009-1:2020, the
requirements of this document take precedence over the requirements of EN 1009-1:2020 for machines
that have been designed and built according to the provisions of this document.
This document, together with EN 1009-1:2020, deals with all the significant hazards, hazardous
situations and events relevant to screening machinery when they are used as intended and under the
conditions foreseen by the manufacturer (see Annex C).
This document does not cover:
— design relating to road traffic regulations;
— hazards arising from the use of the machines in potentially explosive atmospheres as well as from
processing of explosive materials and risks related to electromagnetic compatibility;
— specific hazards related to mobile machinery.
NOTE 1 EN ISO 13766-1 and EN ISO 13766-2 specify test methods and acceptance criteria for evaluating the
electromagnetic compatibility of all kinds of mobile construction machinery.
NOTE 2 prEN 1009-6 “Specific requirements for mobile and semi mobile equipment” is under preparation to
cover specific requirements (e.g. mobility, braking, access, frequent transportation), including exceptions and
additional requirements for mobile and semi mobile equipment. This means that mobile machines are not covered
as long as EN 1009-6 is not published by CEN.
This document is not applicable to screening machinery which are manufactured before the date of
publication of this document by CEN.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 547-1:1996+A1:2008, Safety of machinery — Human body measurements — Part 1: Principles for
determining the dimensions required for openings for whole body access into machinery
EN 547-2:1996+A1:2008, Safety of machinery — Human body measurements — Part 2: Principles for
determining the dimensions required for access openings
EN 1009-1:2020, Machines for mechanical processing of minerals and similar solid materials — Safety —
Part 1: Common requirements for machinery and processing plants
EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk
reduction (ISO 12100:2010)
EN ISO 13854:2019, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
(ISO 13854:2017)
EN ISO 14122-1:2016, Safety of machinery — Permanent means of access to machinery — Part 1: Choice
of fixed means and general requirements of access (ISO 14122-1:2016)
EN ISO 14122-2:2016, Safety of machinery — Permanent means of access to machinery — Part 2: Working
platforms and walkways (ISO 14122-2:2016)
EN ISO 14122-3:2016, Safety of machinery — Permanent means of access to machinery — Part 3: Stairs,
stepladders and guard-rails (ISO 14122-3:2016)
EN ISO 14122-4:2016, Safety of machinery — Permanent means of access to machinery — Part 4: Fixed
ladders (ISO 14122-4:2016)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010,
EN 1009-1:2020 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/ui
— IEC Electropedia: available at http://www.electropedia.org/
NOTE Annex A shows examples of screening machinery.
3.1
screening machinery
stationary or mobile machinery that separates industrial mineral by-products into two or more fractions
by dry or wet process through use of a screen (3.2)
Note 1 to entry: Screening machinery can be installed in a plant, a modular machinery or a mobile machine, as
defined in EN 1009 1:2020, 3.1 to 3.3 and illustrated in Annex B.
3.2
screen
on
...