EN ISO 11611:2007
(Main)Protective clothing for use in welding and allied processes (ISO 11611:2007)
Protective clothing for use in welding and allied processes (ISO 11611:2007)
ISO 11611:2007 specifies minimum basic safety requirements and test methods for protective clothing including hoods, aprons, sleeves and gaiters that are designed to protect the wearer's body including head (hoods) and feet (gaiters) and that are to be worn during welding and allied processes with comparable risks. For the protection of the wearer's head and feet, ISO 11611:2007 is only applicable to hoods and gaiters. ISO 11611:2007 does not cover requirements for hand protection.
This type of protective clothing is intended to protect the wearer against spatter (small splashes of molten metal), short contact time with flame, radiant heat from the arc, and minimizes the possibility of electrical shock by short-term, accidental contact with live electrical conductors at voltages up to approximately 100 V d.c. in normal conditions of welding. Sweat, soiling or other contaminants can affect the level of protection provided against short-term accidental contact with live electric conductors at these voltages.
ISO 11611:2007 specifies two classes with specific performance requirements, i.e. Class 1 being the lower level and Class 2 the higher level.
Class 1 is protection against less hazardous welding techniques and situations, causing lower levels of spatter and radiant heat.
Class 2 is protection against more hazardous welding techniques and situations, causing higher levels of spatter and radiant heat.
For adequate overall protection against the risks to which welders are likely to be exposed, personal protective equipment (PPE) covered by other standards should additionally be worn to protect the head, face, hands and feet.
Schutzkleidung für Schweißen und verwandte Verfahren (ISO 11611:2007)
Diese Internationale Norm legt die grundlegenden Mindestanforderungen an die Sicherheit und die Prüfverfahren für Schutzkleidung fest einschließlich Hauben, Schürzen, Überziehärmel und Gamaschen, die dafür vorgesehen ist, den Träger einschließlich Kopf (Haube) und Füße (Gamaschen) beim Schweißen und verwandten Prozessen mit vergleichbaren Risiken zu schützen. Der Anwendungsbereich dieser Inter¬nationalen Norm umfasst zum Schutz des Kopfes und der Füße des Schweißers nur Gamaschen und Hauben. Diese Internationale Norm legt keine Anforderungen an Handschutz fest.
Diese Art Schutzkleidung ist dazu vorgesehen, den Träger gegen Schweißspritzer (kleine Spritzer geschmol¬zenen Metalls), kurzzeitigen Kontakt mit Flammen sowie Strahlungswärme aus dem Lichtbogen zu schützen und sie bietet unter üblichen Schweißbedingungen in begrenztem Maße elektrische Isolation gegenüber unter Gleichspannung bis ungefähr 100 V stehenden elektrischen Leitern. Schweiß, Verschmutzung oder andere Verunreinigungen können den Schutz gegen kurzzeitiges unbeabsichtigtes Berühren von spannungs¬führenden elektrischen Leitern bis zu dieser Spannung beeinträchtigen.
Diese Internationale Norm legt zwei Klassen mit spezifischen Leistungsanforderungen fest (siehe Anhang A), wobei Klasse 1 die niedrigere Klasse und Klasse 2 die höhere Klasse ist.
Klasse 1 (niedrigere Klasse) bietet Schutz gegen weniger gefährdende Schweißverfahren und Arbeits¬platz¬situationen mit weniger Schweißspritzern und niedrigerer Strahlungswärme.
Klasse 2 (höhere Klasse) bietet Schutz gegen stärker gefährdende Schweißverfahren und Arbeits¬platzsituationen mit mehr Schweißspritzern und stärkerer Strahlungswärme.
Einzelheiten sind in Tabelle 1 und Anhang B angegeben.
Für angemessenen Schutz gegen Risiken, denen Schweißer üblicherweise ausgesetzt sind, sollte Persönliche Schutzausrüstung (PSA) für Kopf, Gesicht, Hände und Füße entsprechend anderen Normen getragen werden.
Vêtements de protection utilisés pendant le soudage et les techniques connexes (ISO 11611:2007)
L'ISO 11611:2007 spécifie les exigences essentielles de sécurité minimales et les méthodes d'essai des vêtements de protection, comprenant les cagoules, les tabliers, les manches et les guêtres, destinés à protéger le corps y compris la tête (cagoules) et les pieds (guêtres) et qui doivent être portés durant des opérations de soudage et autres procédés techniques ayant des risques comparables. Pour la protection de la tête et des pieds, l'ISO 11611:2007 s'applique seulement pour les cagoules et les guêtres. L'ISO 11611:2007 ne couvre pas les exigences pour la protection de la main.
Ce type de vêtement de protection est destiné à protéger celui qui le porte contre les projections (petites projections de métal en fusion), contre le contact de courte durée avec une flamme, contre la chaleur radiante provenant de l'arc et à fournir un certain degré d'isolation électrique en cas de contact accidentel avec un conducteur électrique à un voltage supérieur à approximativement 100 V en courant continu dans des conditions normales de soudage. La sueur, des salissures ou d'autres polluants peuvent affecter le niveau de protection apporté contre un contact accidentel avec un conducteur électrique à ces voltages.
L'ISO 11611:2007 spécifie deux classes avec des exigences de performance, la Classe 1 étant la plus faible et la Classe 2 la plus élevée.
La Classe 1 est la protection contre des techniques de soudage et les situations provoquant le moins de projections et une chaleur radiante faible.
La Classe 2 est la protection contre les techniques de soudage et les situations provoquant plus de projections et une chaleur radiante plus élevée.
Pour une protection complète adéquate contre les risques rencontrés par les soudeurs, il convient que des EPI couverts par d'autres normes soient portés en complément afin de protéger la tête, le visage, les mains et les pieds.
Varovalna obleka za uporabo pri varjenju in sorodnih postopkih (ISO 11611:2007)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Protective clothing for use in welding and allied processes (ISO 11611:2007)Varovalna obleka za uporabo pri varjenju in sorodnih postopkih (ISO 11611:2007)Vetements de protection utilisés pendant le soudage et les techniques connexes (ISO 11611:2007)Schutzkleidung für Schweißen und verwandte Verfahren (ISO 11611:2007)Ta slovenski standard je istoveten z:EN ISO 11611:2007SIST EN ISO 11611:2007en,fr25.160.01Varjenje, trdo in mehko spajkanje na splošnoWelding, brazing and soldering in general13.340.10Varovalna oblekaProtective clothingICS:SIST EN 470-1:1996/A1:1999SIST EN 470-1:19961DGRPHãþDSLOVENSKI
STANDARDSIST EN ISO 11611:200701-december-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 11611October 2007ICS 25.160.01; 13.340.10Supersedes EN 470-1:1995
English VersionProtective clothing for use in welding and allied processes (ISO11611:2007)Vêtements de protection utilisés pendant le soudage et lestechniques connexes (ISO 11611:2007)Schutzkleidung für Schweißen und verwandte Verfahren(ISO 11611:2007)This European Standard was approved by CEN on 20 July 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 11611:2007: E
(informative)
Relationship between this International Standard and the Essential Requirements of EU Directive 89/686/EEC.4
Annex ZA (informative)
Relationship between this International Standard and the Essential Requirements of EU Directive 89/686/EEC
This International Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide one means of conforming to Essential Requirements of the New Approach Directive 89/686/EEC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this International Standard and Directive 89/686/EEC
Clauses/subclauses of this International Standard Essential requirements (ERs) of EU Directive 89/686/EEC, Annex II Qualifying remarks/Notes 4.1 1.2.1 Absence of risks and other inherent nuisance factors
4.2 1.2.1 Absence of risks and other inherent nuisance factors
4.3 1.2.1 Absence of risks and other inherent nuisance factors
4.4 1.2.1 Absence of risks and other inherent nuisance factors
4.2 1.3.1 Adaptation of PPE to user morphology
5.2 1.4 Information supplied by the manufacturer
5.2.3 2.4 PPE subject to ageing
6.1 1.3.2 Lightness and design strength
6.2 1.3.2 Lightness and design strength
6.3 1.3.2 Lightness and design strength
Clauses/subclauses of this International Standard Essential requirements (ERs) of EU Directive 89/686/EEC, Annex II Qualifying remarks/Notes 6.4 1.2.1 Absence of risks and other inherent nuisance factors
6.7 3.6.1 Protection against heat and fire PPE constituent materials and other components
6.7 3.6.2 Protection against heat and fire Complete PPE ready for use
6.8 1.1.2.2 Classes of protection appropriate to different levels of risk
6.8 3.6.1 Protection against heat and fire PPE constituent materials and other components
6.8 3.6.2 Protection against heat and fire Complete PPE ready for use
6.9 3.6.1 Protection against heat and fire PPE constituent materials and other components
6.9 3.6.2 Protection against heat and fire Complete PPE ready for use
6.11 1.2.1.1 Suitable constituent materials
7 1.4 Information supplied by the manufacturer
7 2.12 PPE bearing identification marks relating to health and safety
8 1.4 Information supplied by the manufacturer
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this International Standard.
Reference numberISO 11611:2007(E)© ISO 2007
INTERNATIONAL STANDARD ISO11611First edition2007-10-15Protective clothing for use in welding and allied processes Vêtements de protection utilisés pendant le soudage et les techniques connexes
ISO 11611:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 11611:2007(E) © ISO 2007 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Design.4 4.1 General.4 4.2 Sizes.4 4.3 Pockets.4 4.4 Closures and seams.5 5 Sampling and pre-treatment.5 5.1 Sampling.5 5.2 Pre-treatment of material.5 5.3 Conditioning.5 6 General safety requirements.6 6.1 Tensile strength.6 6.2 Tear strength.6 6.3 Burst strength of knitted materials.6 6.4 Seam strength.6 6.5 Dimensional change of textile materials.6 6.6 Requirements for leather.6 6.7 Flame spread.6 6.8 Impact of spatter.7 6.9 Heat transfer (radiation).7 6.10 Electrical resistance.7 6.11 Innocuousness.8 6.12 Summary of general safety requirements.8 7 Marking.9 8 Information supplied by the manufacturer.9 8.1 General.9 8.2 Intended use.9 8.3 Improper use.10 8.4 Care and maintenance.10 Annex A (informative)
Guidance for the selection of the type of welders' clothing (Class 1/Class 2).11 Annex B (informative)
Information on UV radiation hazards.12 Annex C (informative)
Uncertainty of measurement.13 Bibliography.14
ISO 11611:2007(E) iv © ISO 2007 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical sta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.