EN 1715-4:2008
(Main)Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applications
Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applications
This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for welding applications.
The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1.
This European Standard does not apply to drawn wire.
Aluminium und Aluminiumlegierungen - Vordraht - Teil 4: Besondere Anforderungen für schweißtechnische Anwendungen
Diese Europäische Norm legt die besonderen Anforderungen an Vordraht aus Aluminium und
Aluminiumlegierungen für schweißtechnische Anwendungen fest.
Die allgemeinen Anforderungen und Technischen Lieferbedingungen sind in EN 1715-1 festgelegt.
Diese Europäische Norm gilt nicht für gezogenen Draht.
Aluminium et alliages d'aluminium - Fil machine - Partie 4: Exigences spécifiques relatives aux applications de soudage
La présente Norme européenne prescrit des exigences spécifiques applicables au fil machine en aluminium et
alliages d'aluminium pour les applications de soudage.
Les exigences générales et les conditions techniques de contrôle et de livraison sont spécifiées dans
l’EN 1715-1.
La présente Norme européenne ne s'applique pas au fil étiré.
Aluminij in aluminijeve zlitine - Vlečeni polizdelki - 4. del: Posebne zahteve za varjenje
General Information
- Status
- Published
- Publication Date
- 15-Apr-2008
- Technical Committee
- CEN/TC 132 - Aluminium and aluminium alloys
- Drafting Committee
- WG 35 - Extruded products
- Current Stage
- 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
- Start Date
- 02-Dec-2024
- Completion Date
- 02-Dec-2024
Relations
- Effective Date
- 22-Dec-2008
Overview
EN 1715-4:2008 - "Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applications" (CEN) defines the specific requirements for aluminium drawing stock intended for welding-related uses. It complements the general rules in EN 1715‑1 and explicitly excludes drawn wire. The standard specifies which alloys and tempers are appropriate, what chemical and mechanical information must be reported, and minimum inspection and delivery documentation for manufacturers and purchasers.
Key topics and requirements
- Scope and applicability
- Applies to drawing stock of aluminium and aluminium alloys used for brazing, welding and metal spraying; does not apply to drawn wire.
- Approved alloys
- Lists common welding alloys (examples: EN AW‑1080A, EN AW‑1050A, EN AW‑4043A, EN AW‑4047A, EN AW‑5154A, EN AW‑5356, EN AW‑5556A, EN AW‑5183, EN AW‑5087).
- Chemical composition
- Compositions must conform to EN ISO 18273 (and EN 573‑3 for certain alloys such as EN AW‑1050A and EN AW‑5154A).
- Elements to be reported in the certificate of mass and analysis include Si, Fe, Cu, Mn, Mg, Cr, Ni, Zn, Ti, Ga, V, Be; additional elements specified by referenced standards must also be reported.
- Temper for delivery
- Tempers indicated per EN 515. Typical tempers covered: F (as fabricated) and O3 (homogenised by high temperature treatment). Table 1 provides typical tensile strength ranges for these tempers.
- Inspection and testing
- Chemical composition checked for each cast.
- Mechanical properties measured at least once per coil (or by agreement between manufacturer and purchaser).
- Documentation, marking and packaging
- Delivery includes a certificate of mass and analysis and a test report with alloy ID, temper, diameter, coil IDs, mechanical test results, manufacture and heat‑treatment dates, and net mass.
- Marking and packaging follow EN 1715‑1.
Applications and users
- Useful for: manufacturers of aluminium drawing stock, welding consumable producers, fabricators, welding engineers, procurement officers and quality assurance teams who specify or accept wire feedstock for welding, brazing and thermal spraying.
- Practical applications: ensuring correct alloy selection and temper for weldability, traceability through certificates and test reports, and consistent inspection/testing for quality control of welding feedstock.
Related standards
- EN 1715‑1 - General requirements and technical conditions for inspection and delivery
- EN ISO 18273 - Classification and composition of wire electrodes, wires and rods for aluminium welding
- EN 515 - Temper designations for wrought products
- EN 573‑3 - Chemical composition of wrought aluminium products
EN 1715‑4:2008 is essential for specifying and verifying aluminium drawing stock for welding applications and for maintaining traceability and quality across the supply chain.
Frequently Asked Questions
EN 1715-4:2008 is a standard published by the European Committee for Standardization (CEN). Its full title is "Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applications". This standard covers: This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for welding applications. The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire.
This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for welding applications. The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire.
EN 1715-4:2008 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 1715-4:2008 has the following relationships with other standards: It is inter standard links to EN 1715-4:1997. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 1715-4:2008 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applicationsYDUMHQMHAluminium et alliages d'aluminium - Fil machine - Partie 4: Exigences spécifiques pour les applications soudageAluminium und Aluminiumlegierungen - Vordraht - Teil 4: Besondere Anforderungen für schweißtechnische Anwendungen77.150.10Aluminijski izdelkiAluminium productsICS:SIST EN 1715-4:2008en,fr,deTa slovenski standard je istoveten z:EN 1715-4:200801-julij-2008SIST EN 1715-4:2008SLOVENSKI
STANDARDSIST EN 1715-4:19981DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1715-4April 2008ICS 77.150.10Supersedes EN 1715-4:1997
English VersionAluminium and aluminium alloys - Drawing stock - Part 4:Specific requirements for welding applicationsAluminium et alliages d'aluminium - Fil machine - Partie 4:Exigences spécifiques relatives aux applications desoudageAluminium und Aluminiumlegierungen - Vordraht - Teil 4:Besondere Anforderungen für schweißtechnischeAnwendungenThis European Standard was approved by CEN on 14 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1715-4:2008: E
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...