EN 14353:2007/FprA1

SLOVENSKI STANDARD
01-oktober-2009
3RPRåQLLQGRGDWQLNRYLQVNLSURILOL]DPDYþQHSORãþH'HILQLFLMH]DKWHYHLQ
SUHVNXVQHPHWRGH
Metal beads and feature profiles for use with gypsum plasterboards - Definitions,
requirements and test methods
Hilfs- und Zusatzprofile aus Metall zur Verwendung mit Gipsplatten - Begriffe,
Anforderungen und Prüfverfahren
Cornières et profilés métalliques pour plaques de plâtres - Définitions, spécifications et
méthodes
Ta slovenski standard je istoveten z: EN 14353:2007/FprA1
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 14353:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2009
ICS 91.100.10
English Version
Metal beads and feature profiles for use with gypsum
plasterboards - Definitions, requirements and test methods
Cornières et profilés métalliques pour plaques de plâtres - Hilfs- und Zusatzprofile aus Metall zur Verwendung mit
Définitions, spécifications et méthodes Gipsplatten - Begriffe, Anforderungen und Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 241.
This draft amendment A1, if approved, will modify the European Standard EN 14353:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14353:2007/FprA1:2009: E
worldwide for CEN national Members.

Foreword
This document (EN 14353:2007/FprA1:2009) has been prepared by Technical Committee CEN/TC 241
“Gypsum and gypsum based products”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
1 Modifications to Clause 2
Add the following references:
"EN 10139, Cold rolled uncoated mild steel narrow strip for cold forming - Technical delivery conditions",
"EN 10152, Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery
conditions",
"EN ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2006)",
"EN 10346, Continuously hot-dip coated steel flat products – Technical delivery conditions".
Delete the following references:
"EN 10326, Continuously hot-dip coated strip and sheet of structural steels — Technical delivery conditions
EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming — Technical
delivery conditions".
Replace the references to prEN 15283-1 and prEN 15283-2 with EN 15283-1 and EN 15283-2 in Clause 2
and throughout the document.
Replace the reference to EN ISO 1924-2 with the following:
"EN ISO 1924-2, Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation
method (20 mm/min) (ISO 1924-2:2008)".
2 Addition of 3.1, General terms
Insert the following new sub-clause 3.1 after the standard paragraph:
"3.1 General terms".
3 Modification to 3.1 – 3.14
Replace numbering of clauses 3.1 – 3.14 with 3.1.1 – 3.1.14.
4 Addition of 3.2, Symbols and abbreviations
Insert the following new sub-clause 3.2 after 3.1.14:
"3.2 Symbols and abbreviations
For the purpose of simplification in product marking and performance information characteristics may be
identified through the symbols and abbreviations given in Table 1.
...